Question about 2004 Chrysler Pacifica

1 Answer

How to change the spark plugs in a 2004 Chrysler

Steps needed to change the spark plugs in a 2004 Chrysler Pacifica? What has to be removed to access the plugs?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 3 Answers

Get a haynes manual for a charger it has steps for the v6 to remove the **** to get to your spark plugs

Posted on Jul 29, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change the spark plugs on a 2007 Chrysler Pacifica?


the upper plenum will need to be removed on the 4.0 liter. Once the plenum is out of the way the coils can be removed and the plugs replaced.

on the 3.8 liter remove the plug wires from the plugs one at a time and replace that spark plug. Place the wire back on the plug as soon as it is installed and move on to the next.

Oct 08, 2016 | 2007 Chrysler Pacifica Touring

1 Answer

P0305 2004 chrysler pacifica


Engine misfire could be anything spark plugs, bad coil, fuel pump or filter in tank, pressure regulator,ASD relay, injector or computer

Apr 02, 2014 | 2004 Chrysler Pacifica

1 Answer

Free diagram for a 2004 chrysler pacifica need to know how to change spark plugs need to know how to fix a manifold leak


You are in luck you can fix both at the same time. Disconnect battery Pull off engine cover. Remove air cleaner housing and tube. Remove speed control and accelerator cables remove every bracket from the intake manifold. Remove the ten or so screws holding the intake on Remove dipstick tube bolt. Remove any wires and hoses. Lift it off and that is where the front 3 spark plugs are. Unbolt coils on top of each spark plug and 1/2 turn and pull off. Blow or vacuum everything from the spark plug tubes. Spray penetrating oil down by the plugs and let it soak. Turn the plug a 1/2 turn then turn it back down then out then in so the threads clean themselves remember they were in there for 100,000 miles. Make sure you replace them with platinum or iridium plugs

Aug 26, 2011 | 2004 Chrysler Pacifica

1 Answer

Diagram where are spark plugs in 2004 Chrysler Pacifica and how to replace them


They are under the coil packs. The rear three can be replaced easily with a male 25 torx socket and a 5/8 plug socket. However, the front 3 require removing the air intake plenum first. There are several sensors that need to be unplugged. Also the throttle linkage needs to be unhooked. Several bolts around the edge of the plenum that hold the oil fill, dipstick, support bracket, etc. Also the intake hose clamp needs to be removed. Finally there are seven bolts that hold the plenum to the intake. These 7 bolts have loctite on them that needs to be cleaned off and new applied during installation. Take your time and the plenum comes off easily. Be especially careful not to drop anything down the intake once the plenum is removed. The good news, Chrysler says 70,000 between changes so you don't have to do it very often.

Here is a link to dl the manual as I was unable to find a diagram. Hope this helps some.
http://carservicemanuals.blogspot.com/2010/05/chrysler-pacifica-2004-service-manual.html
Good luck.

May 09, 2011 | Chrysler Pacifica Cars & Trucks

1 Answer

Where are the spark plugs located on a 2006 pacifica 24 valve 3.5 l


HI. Your spark plugs are located and inserted into each cylinder location, just under the respective ignition coil. This engine is designed for a Coil on Plug setup. The ignition coils are attached to each plug in the engine. Once you have removed each plugs respective coil,which is located directly on top of each plug, Then will you notice the plug. When removing the front plugs, be sure to remove the intake manifold to gain full access.

NOTE- Always remove the ignition coil assembly by grasping at the spark plug boot, turning the assembly 1/2 turn and pulling straight back in a steady motion. Only then will you gain access to the plug that is placed in that particular cylinder.

Nov 21, 2010 | 2006 Chrysler Pacifica

1 Answer

Car overheating! Its a 2004 Pacifica. Gauge doesn't change while in park but shoots up while driving.


Hello mayaponce and thank you for asking your question, on Fixya.

Here is a simple process that will walk you through a few steps that will pinpoint the overheating problem on your 2004 Chrysler Pacifica, without even using any tools. It has helped millions of people, and I am certain that it will help you, because I wrote it for people like you. So here is the link to:
How to diagnose your overheating 2004 Chrysler Pacifica

Anyways if that helps you any little bit, then feel free to follow me on Twitter. That one is at: twitter.com/acoates23234

Thanks for the vote, and good luck!

Nov 08, 2010 | 2004 Chrysler Pacifica

1 Answer

I'm trying to change my sparks plugs on a 2004 chysler pacifica. I wanted to how many spark plugs does my car have.


Your Pacifica 2004 has a 3.5L engine 6 cylinder, you will need six spark plug's, the spark plug gap is .050", make sure you gap the spark plug's before you install them, hope this was very helpful.

Aug 26, 2010 | 2004 Chrysler Pacifica

1 Answer

How do you change Spark plugs for an 05 Chrysler Pacifica and where is it located?


is it a DOHC V6 if so ur in luck their is probably a plastic cover on the engine remove that to gain access to the valve cover on the front bank. The spark plugs should be right in the center of the valve cover you'll need to get a 6" or so extension to reach down into the cylinder head to remove them the same steps for the spark plugs on the back bank (closest to the fire wall).

Oct 13, 2009 | 2005 Chrysler Pacifica

1 Answer

Changing my spark plugs


you can do this at home without a lift because your spark plugs are on the top of your motor, but it is a pain. i have an 05. you need to go and get yourself a manual from autozone or advance auto for a 2004 and up charger. it has the 3.5l v6 in there as well and breaks it down on what you ahve to do to change them.

Jun 04, 2009 | 2004 Chrysler Pacifica

3 Answers

Where are the spark plugs located in a 2005 Chrysler Pacifica?


Jay from Ma,
You have it backwards the rear three are accessable with the front three being under the intake. To remove the intake simply remove throttle body and aproxamently 15 other bolts.

Dec 16, 2008 | 2005 Chrysler Pacifica

Not finding what you are looking for?
2004 Chrysler Pacifica Logo

840 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...