Question about 1998 Mercury Sable

1 Answer

Crank shaft puley removal

Not that easy is there a special way to remove it?

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 36 Answers

You can rent pullers from napa

Posted on Jul 12, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Replacement right rear passenger hand operated window have broken window can't get window handle off

U need a special tool to remove handle. There is a clip and this needs a tool that will push the clip off and allowing u to remove handle.

May 10, 2018 | Cars & Trucks

1 Answer

Removing crankshaft timing pulley bolt

a/t or m/t? stick or slush pump.?
with a wrench and deep socket
if all this is unknown to you? this job
why not RTM

alldata dot com
its all there. every step.

if your question was really, how do I hold the crank shaft still
while i remove that huge bolt , that is a different matter
there are 5 ways or more.
with a STICK , select 5th gear, and turn the bolt CCW.
easy huh? mines at 100ft../lbs but my take 150 to pop it loose.
Automatics slush pumps. tranny
well the slush dont hold any crank.

so see all these ways. fsm shows a special too , not sold today.
a RWD car is more easy so FWD , way less.

some use a chain wrench on FWD cars.
or a factory tool

Jan 23, 2013 | Geo Storm Cars & Trucks

1 Answer

Crank shaft

You must remove the engine from the car and then pull it apart to replace the crank, this is a very time intensive job that requires lots of skill and special tools, it is not for the home mech.

Oct 08, 2012 | 1998 Dodge Intrepid

1 Answer

How to replace a timing gear

Remove the bolt in the center of the crank shaft damper pulley

Use a special puller to remove the pulley

Remove the timing cover & use a puller if doing the
crank gear,most likely your doing the top cam gear
because it has plastic teeth or used to have teeth.

May have to remove water pump as well to get cover off

Sep 24, 2011 | 1991 Buick Riviera

1 Answer

Change a crankshaft position sensor on a 2000 eclipse

Is this a V6 or 4cyl???>>>(V6) This requires removing the Harmonic balancer (crankshaft pulley). Remove (R) front wheel, remove engine splash Guard, Remove crank pulley, remove lower timing belt cover. The Crank sensor is located behind the crank shaft pulley!! I highly recommend having this done by a certified tech, requires special tools. Hopefully this helps!!

Mar 11, 2010 | 2000 Mitsubishi Eclipse

1 Answer

Is there a special tool needed to take off the crank shaft pulley on a 1990 honda accord

If your having issues removing the crank pulley bolt you can get a special tool from snap on tools.It slides inside the pulley and holds it in place so you can break the bolt loose.Once the bolt is removed the pulley will slide off.

Feb 07, 2010 | 1990 Honda Accord

1 Answer

How do you remove the window knob on a 1994 buick skylark-manual window

there is a special tool that can be purchased that slides between the crank and the door panel. It is used to remove the retaining clip that holds the crank on the shaft.
On some older cars I have fashioned a small hook that I slide between the crank and the panel to grab and remove the retaining clip. Once the clip is removed the crank slides off the shaft.

Oct 10, 2009 | 1994 Buick Skylark

1 Answer

How to remove crank shaft bolt gmc s 15

you need an air impact gun to get retaining bolt out/off, then a pulley puller special tool to remove the pulley once the bolt is out, the pulley is pressed on.

Sep 15, 2009 | 1988 GMC S-15

1 Answer

Focus timing belt replacement.

This is a very very easy timing belt setup. first off you have to remove the valve cover. Then you have to remove the serp belt. Then remove anything thats in your way of the front cover. after you remove the crank pulley re-install the crank bolt. DO NOT LOSEN THE BOLT FOR THE TENSIONER!!!! now spin the crankshaft until the sproket aligns with the timing mark. now at this point the two camshafts should be aligned. now there is a special tool from ford that holds the cam shafts in place. all it is is a 1/4" peice of metal that goes on the left side of the cam shafts to hold them into place. if you mark the cams you wont need the tool. or if you can find something to fit in the left side of the cams that will work too. anyways after that its just the same steps in reverse. very easy to do.

Aug 29, 2009 | 2002 Ford SVT Focus

Not finding what you are looking for?
1998 Mercury Sable Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts


Level 3 Expert

80339 Answers


Level 3 Expert

5687 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides