Question about 1989 Toyota Camry

1 Answer

Where is the oxygen sensor on a 1996 infiniti , how many are there? how much should they cost and how would i replace them.

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 58 Answers

Well you didn't say which engine you have so I selected a typical V6 from that year. See below. There is one sensor between each exhaust manifold and Catalytic converter, Many vehicles also have an additional O2 sensor afret the Catalytic converter.

They are removed & replaced with special deep set slotted socket wrenches. These tools can usually be borrowed from the local chain supply stores.

where is the oxygen sensor on a 1996 infiniti - o2%20infin.jpg46b2982.jpg

Posted on Sep 04, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

1998 Infiniti I30 trouble code P0134 were are the oxygen sensors?

code p 0134 refers to heated oxygen sensor(HO2S) 1 bank 1--no activity detected ===causes ---wiring open circuit--heating inoperative---HO2S sensor
it also refers to oxygen sensor (O2S) 1 bank 1 --no activity===causes wiring -- oxygen sensor
HEATED oxygen sensors are in the exhaust manifold or exhaust pipe before the cat converter
oxygen sensors are in the exhaust pipe after the cat converter
bank one is the side closest to the radiator on a cross fitted engine or on the lhs with you facing the fan

Aug 10, 2016 | Infiniti Cars & Trucks

1 Answer

Oxygen sensor wiring

You return it and buy the correct one to fit your car

Feb 13, 2018 | Cars & Trucks

1 Answer

Check engine light flashing

This is part of your computer system to tell you that you have to take it back to the dealer for servicing. Usually it means that the oxygen sensor, mounted somewhere in your exhaust system is indicating that the ratio of oxygen to burned gas is not exactly right.

In the cases that I have seen, it was the sensor itself that had failed and replacing that sensor cured the problem. The sensor sells for 50-100 bucks and cost another 50 bucks to have it replaced.

Dec 14, 2010 | 1996 Toyota T100

1 Answer

Where is the oxygen sensor located on a lincoln town car 96

My 96 has 4 cat converters, 2 (upstream and down stream) on each side. There are 2 oxygen sensors on each side, before upstream converter and after upstream converter. But make sure they are bad before you replace them (4 of them will cost you about $200), and my 1996 with 175K has 3 original still running. Other sensors (air flow, coolant temp) might be the problem as well.

Sep 27, 2010 | 1996 Lincoln Town Car

1 Answer

P 0734 -gear 4 incorrect ratio and P 0150 oxin sensor circut ( band 2 sensor 1\r\n and car will not pass smog what do we do a 1996 i30 infiniti

The first code could be due to a shift solenoid in the transmission. you can have a transmission shop use a scanner to observe the shift patterns while driving it, some will do free diagnostics if you shop around. the second code is for your oxygen sensor, you will need to replace it because if bad it can cause the engine computer to make the car run lean or rich and will make it fail said smog tests. the sensor the code is referring to is your upper sensor, if it is a v6 model it will be on the passenger side upper or if it is a 4 cylinder model it will be the only upper sensor.

May 18, 2010 | Infiniti J30 Cars & Trucks

1 Answer

Code says all 4 o2 sensors bad.

The Oxygen sensor is bad and your car is telling you this. The sensor measures the amoung of Oxygen in the burned gasses. Replace it for about $125.00 or have it done for around $150 - $200.

Warning, if you don't have experience and the special tool, you will probably break the first one ... doubbling the cost of parts.

Thanks for your interest in

Jan 20, 2010 | 2003 Nissan Maxima

1 Answer

I'm getting four different fault codes for my 2000 infiniti i30. I have canceled all the codes several times but they always come back within a month or two. The i30 runs fine in every respect. The codes...

Sensor 2(s) are those aft of the catalytic converter(s).
The pre-cat sensors typically fail more frequently than those post-cat.
The codes you cite are related to all sensors.
It is worth running a test of the sensors. Most garages can do the tests without any disassembly and for less than the cost of replacing any one of the four. Then you can replace the faulty unit with confidence.

Aug 27, 2009 | Infiniti I35 Cars & Trucks

1 Answer

Oxygen sensor

you need to borrow the oxygen sensor wrench from autozone or whereever you bought the sensor. Section 03-14: Engine Controls, Electronic 1996 Taurus, Sable Workshop Manual REMOVAL AND INSTALLATION -------------------------------------------------------------------------------- Heated Oxygen Sensor (HO2S) SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Oxygen Sensor Wrench T94P-9472-A Removal and Installation Disconnect battery ground cable (14301). Refer to Section 14-01 . On 3.0L (4V) engine remove cowl extension and right side of leaf screen. Disconnect engine control sensor wiring (12A581) from heated oxygen sensors (HO2S) (9F472). Do not remove harness connectors from the brackets. Raise vehicle on hoist. Refer to Section 00-02 . NOTE: If excessive force is needed to remove a heated oxygen sensor, lubricate the heated oxygen sensor with penetrating oil prior to removal. Remove heated oxygen sensors from exhaust manifolds (9430) using Oxygen Sensor Wrench T94P-9472-A. To install, reverse Removal procedure. Apply a coating of anti-sieze compound to threads of heated oxygen sensor. Tighten heated oxygen sensors to 34-46 Nm (26-34 lb-ft).

Jun 13, 2009 | 1996 Ford Taurus

2 Answers

Oxygen sensors, knock sensor

it under intake goood luck

Aug 11, 2008 | 2008 Infiniti FX35

Not finding what you are looking for?
1989 Toyota Camry Logo

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

80531 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides