Question about 1995 Jeep Wrangler

3 Answers

HELLO EXPERTS I have a 1995 jeep wrangler with 2.5 engine and five speed trans. I've put about 1000 miles on a new clutch, pressure-plat, throw-out bearing and slave cylinder. I am experencing the following problems: 1. With the clutch pedal fully depressed the clutch remains engaged and jeep wants to move forward. The engine has died at stop signs when the clutch and brake are fully applied. 2. When moving the trans refuses to shift and has to be stronged armed into the next gear. With resulting grinding of gears I might add. 3. Sometimes I cannot shift out of gear. 4. Sometimes the clutch shifts as in the good old days. 5. Sometimes the trans remains locked in a gear and I've turned off the motor and was able to shift again after starting the engine again. If I recall correctly these same problems occurred previous to replacing the above parts although to a lesser degree. Thank you for any help anyone can provide. Marco

Posted by on

Ad

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 6,982 Answers

Check all your hydraulic connections for seepage . If you find nothing leaking, check where the rod goes into the master cylinder under the dashboard...If still nothing, I'd change the master cyl, as it is likely internally bypassing and permitting the clutch to release. PS it takesa a special "touch" to shift gears without using the clutch, if you cannot do that don't drive it Till you get it fixed...you will damage synchros and will need to have trans removed and rebuilt. $$$you don't want to spend!!!

Posted on Jul 12, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

If you had spline wear on input shaft of trans. sometimes the new clutch disc will hang up on the wear spot in the spline if the wear is bad enough

Posted on Oct 04, 2011

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I replaced three slave cylinders before I found out that you are suppose to replace the seal behind it too. There is a service bulitine on that, the original slave cylinder was defective about half went bad. When you put the new and improved model on you had to change the seal also. My dealer did not know about this. My jeep is a 1992 and did the same things yours is. n1rur@yahoo.com

Posted on Aug 24, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1995 Toyota Tacoma 3.4L 5-speed manual feels like 4x4 is not fully engaging.


check that the clutch is fully engaging by checking if there is free play at the throw out lever and clutch push rod . If you cannot push the rod back into the cylinder then the slipping is because the clutch is only partially engaged. Replace the clutch master cylinder if that is the case. If it is right then the fault will be in the pressure plat/ cutch plate and it may require a clutch kit.

Feb 05, 2014 | Cars & Trucks

2 Answers

I have a 2004 Jeep Wrangler 4 cyl. The CEL came on. Had no power for a little bit. Went to autozone and it pulled code P0870. Any suggestions.


po 870 refers to transmission fluid pressure- check fluid level of trans while parked with engine running and the jeep level.- if level is ok- might be time to have filter and fluid changed

Sep 15, 2011 | 2004 Jeep Wrangler

1 Answer

I have a 97 jeep wrangler with I-4 manual trans. Rattle in trans at a stop with clutch in and out. at one time there was a whine also but now that is gone. I dont drive this much. only 52,000 miles on her....


Rember when you press the clutch in, the pressure plate releices the clutch disc and input shaft in the transmission. If you still have noise, It can only be either a broken spring on the pressure plate or the throw out berring. Neither can be serviced. There is a fill plug on the side, It takes ATF

Jun 18, 2010 | 2004 Jeep Wrangler

2 Answers

The clutch slips in first gear when it is hot.


You need a new clutch again. Sorry to give ya the bad news. This time make sure they put a new transmission seal in so fluid can not leak onto the clutch plate and ruin it.

Apr 25, 2010 | 1999 Jeep Wrangler

1 Answer

95 wrangler yj. has no power at high speeds


Have you had fuel pressure tested, and/or filter changed. Have you checked for plugged exhaust, such as catalytic converter? Quite often engine will also run a little hotter than normal when exhaust is plugged.

Nov 05, 2009 | 1995 Jeep Wrangler

1 Answer

I have a 90 jeep wrangler, 4cyl and 5 speed transmission, when i accelerate in any of the gears, it makes a popping noise and the second it makes that noise it seems like the jeep stops pulling, if you...


It sounds like it is the throw out bearing. From your description of the vehicle not pulling its weight, it is going to need a clutch. The throw out bearing will come in most clutch kits, so when you replace the clutch you can replace the throw out bearing, pressure plate, and pilot bushing.

Oct 18, 2009 | 1990 Jeep Wrangler

1 Answer

How do I change out the clutch in my 1995 Jeep Wranger 4x4?


support the engine, drop the drive lines, pull trans and tranfer case, un bolt clutch, have fly wheel turned and put back together

Oct 01, 2009 | 1995 Jeep Wrangler

2 Answers

Second tinme throw out bearing has to be replaced.


This is a weird one. Unless there is a TSB on bad bearings from the dealer, the only thing I could GUESS is a bad pressure plate, but you said you are replacing the whole thing.

Nov 22, 2008 | 2008 Jeep Wrangler

1 Answer

Jeep Troubles


sounds like the clutch is failing before changing the clutch check the trans fluid for metal hunks or sliver fluid if that is present u might have an internal trans failure

Jun 19, 2008 | 2000 Jeep Wrangler

Not finding what you are looking for?
1995 Jeep Wrangler Logo

475 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...