Question about 2002 Chrysler Sebring

2 Answers

Tie rod end replacement on sebring 2002 any special tools

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Chrysler Master
  • 3,433 Answers

No, but yes. a tie rod end pickle fork.

Posted on Jul 12, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 414 Answers

Nope just wrenches.

Posted on Jul 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I tighten screw on inner tie rod?


The inner tie rod requires a special tool and you have to separate the outer tie rod end off the tie rod. My suggestion is buy a repair manual for your vehicle at the parts store and read this section it is well explained. If there is play on the inner tie rod it needs to be replaced.

Nov 07, 2015 | 1997 Chevrolet Suburban

1 Answer

Inner tie rod removal with tool


One end of the tie rod is a left hand thread
make sure that you are turning it the right way

Apr 12, 2015 | 2005 Hyundai Tucson GLS

2 Answers

How to replace tie rod ends on an Xterra


Special tools are necessary to replace tie rod ends. After the tie rod ends are replaced, it is mandatory to have an alignment done.

Sep 29, 2014 | 2002 Nissan Xterra

1 Answer

2002 FORD TAURUS INNER TIE ROD END


They screw on & then are cripped with a special tool

Dec 24, 2012 | 2002 Ford Taurus

1 Answer

How to replace tie tods on a 2001 and should both tie rods have a grese fighting or just one. and how to get the bands off to remove the boot .


ok, Tie rods don't have boots. The only thing up front with a boot is the CV joint. You have to use a cutter to remove the bands from a CV joint however, unless your trying to repair the joint you don't want to do that. There is no lubrication point inside the boot you need to reach. If for some reason you need to remove that boot you need to get a CV joint Boot Repair kit to do this as it will have replacement bands to use in the repair. Because of the nature of a CV joint and it's importance to operating correctly I don't recommend trying to do a Joint repair on your own. On the Tie Rod typically you will replace the out end. You need to have a tie Rod puller to remove the tie rod end off the "A" frame after you have released the lock nut in the center then simply unscrew the tie rod end. You'll want to make sure you mark the old tie rod somehow so you can put beside the new part and mark it so you know how far to screw that in so the Alignment matches, as close as possible. The tie rod puller is a special tool you can get from Auto Zone to remove the Tie rod end from the "A" frame.

Oct 27, 2010 | 2002 Chrysler PT Cruiser

1 Answer

Impact bent the right front tie rod. how can it be removed for straightening or replacing?


First loosen the jam nut with a 21mm wrench. Then use vise grips or whatever you have to make sure the rod can be turned that goes into the outer tie rod. Then remove the cotter pin and 17mm castle nut. Strike the hub where the tie rod goes through with a hammer repeatedly until the tie rod pops out of the hole.

Then simply unscrew the tie rod end and replace it. If the inner tie rod end is also damaged, or the rod is damaged you will need to replace them as well. Inner tie rods have a special tool to remove them, see your local auto parts store.

Remember, replacing an outer tie rod end changes your cars toe (alignment). You will require an alignment after replacing it, even if you think the car drives straight.

Good luck!

Nov 30, 2009 | 2002 Hyundai Accent

1 Answer

Do i need special tools to replace the inner tie rod ends on my 02 monte carlo thx larry


nothing special just a socket set a hammer and large cresent wrench should do it and youll prob need to get it aligned after there replace

Nov 11, 2009 | 2002 Chevrolet Monte Carlo

4 Answers

How do I replace the upper ball joints in my 2002 Ford Explorer?


The upper ball joints are replaceable without replacing the control arms. Use Moog K80008 ball joints and a ball joint press.

Jun 25, 2009 | 2002 Ford Explorer

1 Answer

How to replace left inner tirerod (Special tools?)


To make it easier, when you stop at autoparts store, ask for a "crowsfoot wrench'" to fit the new inner tie rod. Should be able to get it in 3/8' or 1/2 " drive to fit ratchet. It's basically the end of an open end wrench, with square drive for ratchet to fit into.

Apr 23, 2009 | 2002 Chrysler Town & Country

2 Answers

Tie rod problem 98 Dodge


There is a tool that you can use that will make it easier for you. To get to the tie rod end, remove the wheel and take the outer tie rod end loose from the hub. You will have to use a hammer and hit the socket where the end goes into the hub to free it up. Once you have the tie rod loose from the hub, loosen the nut behind the outer tie rod end. Count the revolutions as you unscrew the outer end off and write te number down so you will know how far to put it back on. This will save your alignment. Now, the end that is still there is your inner tie rod end. You will have to undo the bellows boot to get to the nut. The tool will slide over the end and secure onto the nut. Now you just unscrew this and replace with you new inner tie rod end.
Please remember to rate this fix.

Feb 16, 2009 | 1998 Dodge Grand Caravan

Not finding what you are looking for?
2002 Chrysler Sebring Logo

Related Topics:

262 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...