Question about 1995 Mercury Tracer

1 Answer

How do you align the camshaft & crankshaft timing marks 1.9

How can I align these two cam & crankshafts on a 1995 mercury tracer 1.9 The tensioner came loose and now the timing is off ! now, I do not know how to set the timing back. I do have the CHILTON repair manual but it ONLY shows how to put the timing belt back on the pulley. It says to ALIGN THE TIMING MARK ON THE CYLINDER HEAD, so do I just turn the camshaft sprocket and line-up the arrow with the hole on the cylinder head? and if so, what tool is needed to turn the cam and the crankshafts. Also, do I need to keep the belt on the pulleys when I turn the shafts? please help me out

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 23 Answers

This is the same as a Ford Escort 1.9, the #1 cylinder should be all the way up. To confirm- the crak shift mark should be on zero which is Crank Shift Center- THe camshift sproket should align with the headmark. Make sure both marks don't move. Align the belt- not too tight , not to loose

Posted on Jul 12, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

03 Saturn vue 160 lb compression on 1/3/5 no compression on 2/4/6 timing marks are lined up.


You have 2/4/6 timing marks 180 degress out on exhaust or intake cam .

Did your special tool ?
Rotate the crankshaft using the J 42098 until the #1 cylinder is at 60 degrees before top dead center (BTDC).
Install theJ 42069 Crankshaft Locking Tool.
Rotate the crankshaft in the engine rotational direction (clockwise) using the J 42098 until the #1 cylinder is at top dead center (TDC) and tighten the lever arm to the water pump pulley flange.
Important: Ensure that the alignment of the crankshaft is not 180 degrees off. The alignment mark must align with the corresponding notches on the rear timing belt cover.
Install the 1-2 and 3-4 camshaft locks, the J42069-1 Timing Belt Alignment Kit and the J42069-2.
Important: Do not rotate the crankshaft if the camshafts are not locked in place with the 1-2 and 3-4 camshaft locks (J42069-1 and J42069-2).
Important: Do not rotate the camshafts unless the crankshaft is at 60 degrees BTDC or the valves may contact the crankshaft.
Loosen the tensioner pulley.
Remove the timing belt.

Jan 09, 2017 | Saturn Vue Cars & Trucks

1 Answer

How to aliane marks on cam shaft pulley on mazda protege 2002


1. Remove all spark plugs so that the crank shaft could be rotated easily.
2. Rotate the crankshaft to align the timing mark of the crankshaft gear with the index mark on the engine cover.
3.Rotate the crankshaft +/- 30 degrees to ensure that the valve could not hit the pistons when aligning the camshaft gears.
4. Align the camshafts as described below.
5. Align the crankshaft timing gear with the index mark.
6. Loose and lock the timing bearing at its farther position. Install a timing belt starting from the crankshaft gear, then right cam, then left cam, and at last the timing bearing.
7. Press and hold the timing belt to keep it firm on the gears and loosen the timing bearing. It will get adjusted by itself with the help of spring attached to it. Do not put extra force on the bearing to adjust it more.
8. Confirm the timing marks.
25659142-ts5vql1j3jwqenesgxdwpnsg-5-0.png

Apr 22, 2015 | 2002 Mazda Protege

1 Answer

Como poner la banda de tienpo de un toyota camery


Installation
1.Install No. 2 idler pulley (if removed). Install and tighten bolt to specification. See TORQUE SPECIFICATIONS . Ensure idler pulley is clean and rotates smoothly. 2.Install No. 1 idler pulley and tension spring (if removed). Pry No. 1 idler pulley away from timing belt area as far as possible. Temporarily tighten No. 1 idler pulley bolt. Ensure idler pulley is clean and rotates smoothly. 3.Using crankshaft pulley bolt, rotate crankshaft so timing mark on crankshaft sprocket aligns with timing mark on oil pump housing. See. This will position keyway in crankshaft sprocket at 12 o'clock position.

CAUTION:If reusing timing belt, ensure reference marks on timing belt align with reference marks placed on crankshaft and camshaft sprockets. Ensure timing belt is installed in original direction of rotation.
4.Ensure all sprockets and idler pulleys are clean. Install timing belt on crankshaft sprocket, oil pump sprocket, No. 1 idler pulley, and then No. 2 idler pulley in sequence. 5.Install timing belt guide with cupped side away from crankshaft sprocket and flat side toward timing belt. Install No. 1 timing belt cover and new gasket. 6.Align crankshaft pulley key groove with key in crankshaft. Install crankshaft pulley. Install and tighten crankshaft pulley bolt to specification. 7.Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover. If reusing timing belt, ensure reference mark on timing belt aligns with upper edge of No. 1 timing belt cover. 8.Rotate camshaft, and align hole in camshaft sprocket with alignment mark on camshaft bearing cap. See Fig. 2 . Install timing belt on camshaft sprocket. If reusing timing belt, ensure reference mark on timing belt aligns with the reference mark on camshaft sprocket. Ensure tension exists on timing belt between the crankshaft and camshaft sprockets.
CAUTION:DO NOT rotate crankshaft counterclockwise, as viewed from timing belt end of engine.
9.Loosen No. 1 idler pulley bolt 1/2 turn. Rotate crankshaft pulley 2 full revolutions clockwise from TDC to TDC. 10.Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover, and hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. See Fig. 2 . If timing marks are not aligned, remove timing belt and reinstall. 11.Rotate crankshaft clockwise 1 and 7/8 revolutions and align crankshaft pulley "0" mark with 45-degree Before Top Dead Center (BTDC) mark on No. 1 timing belt cover. See Fig. 5 . 12.Tighten No. 1 idler pulley bolt to specification. See TORQUE SPECIFICATIONS . Install No. 2 timing belt cover and gaskets. Install and tighten spark plugs to specification. 13.To install remaining components, reverse removal procedure. Install all bolts/nuts on right (timing belt side) engine mount before tightening to specification. 14.On Camry, when installing control rod and bracket on strut tower and right (timing belt side engine mount, tighten bolts to specification in sequence.

Dec 23, 2010 | 1993 Toyota Camry V6

1 Answer

How do you set the timming on a 2.3 when your putting the new timming belt on


The IGNITION timing on your Ranger is computer-controlled and is not adjustable.


Should the camshaft drive belt/timing belt jump timing by a tooth or two, the engine could still run; but very poorly. To visually check for correct timing of the crankshaft, auxiliary shaft, and the camshaft follow this procedure:
There is an access plug provided in the cam drive belt cover so that the camshaft timing cam be checked without moving the drive belt cover.
  1. Remove the access plug.
  2. Turn the crankshaft until the timing marks on the crankshaft indicate TDC.
  3. Make sure that the timing mark on the camshaft drive sprocket is aligned with the pointer on the inner belt cover.

Never turn the crankshaft of any of the overhead cam engines in the opposite direction of normal rotation. Backward rotation of the crankshaft may cause the timing belt to slip and alter the timing.
REMOVAL & INSTALLATION

See Figures 1, 2 and 3


0996b43f80211842.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 1: Timing belt cover on the 2.3L and 2.5L engine


0996b43f80211843.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 2: Timing belt assembly on the 2.3L and 2.5L engine


0996b43f80211844.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 3: Releasing the timing belt tensioner using a special tool

  1. Rotate the engine so that No. 1 cylinder is at TDC on the compression stroke. Check that the timing marks are aligned on the camshaft and crankshaft pulleys. An access plug is provided in the cam belt cover so that the camshaft timing can be checked without removal of the cover or any other parts. Set the crankshaft to TDC by aligning the timing mark on the crank pulley with the TDC mark on the belt cover. Look through the access hole in the belt cover to make sure that the timing mark on the cam drive sprocket is lined up with the pointer on the inner belt cover.

Always turn the engine in the normal direction of rotation. Backward rotation may cause the timing belt to jump time, due to the arrangement of the belt tensioner.
  1. Drain cooling system. Remove the upper radiator hose as necessary. Remove the fan blade and water pump pulley bolts.


Dec 11, 2010 | 1995 Ford Ranger Supercab

1 Answer

After timing car will not start 1998 Mercury Tracer 2.0 Not ZETEC


Sound like you have camshaft where it should be at, align crankshaft pulley key way up, should have a mark or cut on crank gear there will be a mark on housing 12 o'clock align there. 2.0L engine code (p).Hope this was very helpful.Good luck.

Dec 26, 2009 | 1998 Mercury Tracer

1 Answer

How do i set the timing on the balancing shaft(just replaced the belt) of a 1995 misubishi rvr 2.0L sports gear


1- Take off all spark plug so you can turn the crankshaft easily to align Top Dead Center (TDC) . 2- Take off the engine cover to see the notch mark on the cam shaft. 3- Turn the crankshaft until the mark on the pulley match with the 0 on the timing mark. At this point if the mark on the camshaft all align then you are good. If it is not then you have to take off the timing belt to do the correct alignment as following items # 4 to 7. 4- Turn the crankshaft until the Piston # 1 is at top. Put in a screw driver to make sure it is at the top. Make sure the Crank shaft at 0 mark. If not, keep turning until it is at desired position. 5- Turn the camshaft to align at the mark in the straight line with the crankshaft mark. 6- Make sure the camshaft lobe is not pressing to open the intake or exhaust valve for piston # 1. This is to ensure it is at ignition stage: Piston is up, all valves closed. 7- Once everything is aligned at TDC, put the timing belt on. Tighten the tension adjuster, then you are good to go.

Nov 11, 2009 | 1987 Mitsubishi Passenger

1 Answer

How to set timming belt,cant find mark for crankshaft 3.0L


Timing belt removed, static timing was not set before removing timing belt.

[Set Static Timing:
No.1 piston is brought up to TDC before removing timing belt.

Cam gear has a punchmark on face of gear, and this mark aligns with one single tooth. There is a matching punchmark on the Timing Belt Rear Upper Cover.

Facing the cam gear, the mark is to the upper right. There is an 'egg shape' of the timing belt upper rear cover, in this spot. This punchmark is in that 'egg shape', and is close to a bolt hole. The cam gear mark lines up with the Timing Belt Rear Upper Cover, mark.

The crankshaft gear has a punchmark on the face. It lines up with one single tooth. There is a corresponding punchmark on the lower right side. An alignment mark)

Should be a round punchmark on the face of the crankshaft gear. It lines up with a single tooth. Wipe the gear clean, use a little carb cleaner. (NO flames, or sparks nearby, well ventilated area)

Barring you cannot find the crankshaft mark, find the camshaft alignment marks, make sure they are aligned with the alignment, (Punchmark), on the Timing Upper Rear Cover.

Count the teeth in the timing belt. There should be 133 teeth on the belt.

There is 43 teeth in-between the timing mark of the camshaft, and the timing mark on the crankshaft.

(43 teeth in-between the Right Side Camshaft mark to crankshaft mark, 43 teeth in-between the Left Side Camshaft mark to crankshaft mark)

There should be 40 teeth in-between the two cam gears.




Oct 24, 2009 | 1989 Nissan Pathfinder

1 Answer

Timing belt timing marks, 1997 ford escort where are they?


Ford Escort/Tracer 1991-1999 Repair Guide

REMOVAL & INSTALLATION 1.8L Engine

(see Figures 1, 2, 3 and 4)
  1. Disconnect the negative battery cable.
  2. Remove the timing belt covers.
  3. Rotate the crankshaft and align the timing marks located on the camshaft pulleys and the seal plate.
  4. Remove the crankshaft pulley and hub.
  5. If the timing belt is to be reused, mark an arrow on the belt to indicate its rotational direction to enable correct re-installation.
  6. Loosen the timing belt tensioner lockbolt and remove the timing belt.
To install:
  1. Temporarily secure the timing belt tensioner in the far left position with the spring fully extended, then tighten the lockbolt.
  2. Make sure the timing marks on the timing belt pulley (crankshaft sprocket) and the engine block (oil pump housing) are aligned.
  3. Make sure the timing marks on the camshaft pulleys and the seal plate are aligned.
  4. Install the timing belt.
  5. Loosen the tensioner lockbolt. Using a suitable prying tool, position the timing belt tensioner so the timing belt is taut, then tighten the tensioner lockbolt.
  6. Turn the crankshaft two turns clockwise and align the timing belt pulley mark with the mark on the engine block.

fbe49f2.jpg
Fig. 1: Timing marks are located on the camshaft pulleys as shown-1.8L engines

5bb74d0.jpg

Fig. 2: Make sure that the crankshaft sprocket (timing belt pulley) and oil pump timing marks are aligned-1.8L engines

9cafc26.jpg

Fig. 3: Align the timing belt pulley mark with the tension set mark, at approximately the 10 o'clock position-1.8L engines

72dc9cd.jpg
Fig. 4: Check the timing belt deflection at the location shown-1.8L engines

  1. Make sure the camshaft pulley marks are aligned with the seal plate marks.
If the timing marks are not aligned, remove the belt and repeat the procedure.


I hope help you with this; remember rated this help. Good luck.

Sep 11, 2009 | 1997 Ford Escort

1 Answer

Timing for tropper 6cly and 4 camshafts and 24 valves model 2000


Timing Belt
Removal
1. Disconnect battery ground cable.
2. Remove air cleaner assembly.
3. Remove radiator upper fan shroud from radiator.
4. Move drive belt tensioner to loose side using wrench
then remove drive belt.
850RW001
Legend
(1) Crankshaft Pulley
(2) Cooling Fan Pulley
(3) Tensioner
(4) Generator
(5) Air Conditioner Compressor
(6) Power Steering Oil Pump
(7) Drive Belt
5. Remove cooling fan assembly four nuts, then the
cooling fan assembly.
6. Remove cooling fan drive pulley assembly.
7. Remove idle pulley assembly.
8. Remove serpentine belt tensioner assembly.
9. Remove power steering pump assembly.
10.Remove crankshaft pulley assembly using
5–8840–0133–0 crankshaft holder, hold crankshaft
pulley remove center bolt, then the pulley.
11. Remove right side timing belt cover then left side
timing belt cover.
12. Remove lower timing belt cover
13. Remove pusher.
CAUTION: The pusher prevents air from entering
the oil chamber. Its rod must always be facing
upward.
014RW011
Legend
(1) Up Side
(2) Down Side
(3) Direction For Installation
(4) Locking Pin
14. Remove timing belt.
CAUTION:
1. Do not bend or twist the belt, otherwise its core
could be damaged. The belt should not be bent at
a radius less than 30 mm.
2. Do not allow oil or other chemical substances to
come in contact with the belt. They will shorten
the life.
3. Do not attempt to pry or stretch the belt with a
screw driver or any other tool during installation.
4. Store timing belt in a cool and dark place. Never
expose the belt direct sunlight or heat.
6A–30 ENGINE MECHANICAL
Installation
NOTE: For correct belt installation, the letter on the belt
must be able to be read as viewed from the front of the
vehicle.
014RY00042
Legend
(1) Crankshaft Timing Pulley
(2) RH Bank Camshaft Drive Gear Pulley
(3) Water Pump Pulley
(4) Idle Pulley
(5) LH Bank Camshaft Drive Gear Pulley
(6) Tension Pulley
014RY00043
Legend
(7) Alignment Mark on Oil Pump.
(8) Alignment Mark on Timing Belt
(9) Alignment Mark (notch) on Crankshaft Timing
Pulley.
(10) Alignment Mark (groove) on Crankshaft Timing
Pulley.
014RW006
Legend
(1) Timing Belt
(2) Engine Rotation Direction
(3) Cylinder Head Side
1. Install timing belt.
1. Align the mark (notch) of crankshaft timing pulley
(2) with mark on oil pump (1).
Align the mark (groove) on the crankshaft timing
pulley (3) with alignment mark (white dots line) on
the timing belt (4).
NOTE: When timing marks are aligned, No.2 piston will
be on Top Dead Center.
014RW003
Legend
(1) Alignment Mark on Oil Pump
(2) Groove on Crankshaft Timing Pulley
(3) Alignment Mark on Crankshaft Timing Pulley
(4) Alignment Mark on Timing Belt
ENGINE MECHANICAL 6A–31
2. Align the alignment mark on the RH bank
camshaft drive gear pulley (2) to the alignment
mark of the cylinder head cover RH (3).
3. Align the alignment mark (white line) on the timing
belt (1) with alignment mark on the RH bank
camshaft drive gear pulley (2) (on the left side as
viewed from the front of the vehicle) and put the
timing belt on the camshaft drive gear pulley.
Secure the belt with a double clip or equivalent
clip.
014RW00004
Legend
(1) Alignment Mark on Timing Belt (White line).
(2) Alignment Mark on Camshaft Drive Gear
Pulley.
(3) Alignemnt Mark on Cylinder Head Cover RH.
4. Align the alignment mark on the LH bank
camshaft drive gear pulley (2) to the alignment
mark of the cylinder head cover LH (3).
5. Align the alignment mark (white line) on the timing
belt (1) with the alignment mark on the LH bank
camshaft drive gear pulley (2).
When aligning the timing marks, use a wrench to
turn the camshaft drive gear pulley, then set the
timing mark between timing belt and camshaft
drive gear pulley and put the timing belt on the
camshaft drive gear pulley.
Secure the belt with a double clip or equivalent
clip.
NOTE: It is recommended for easy installation that the
belt be secured with a double clip or equivalent clip after
it is installed the timing belt to each pulley.
014RW00005
Legend
(1) Alignment Mark on Timing Belt (White line).
(2) Alignment Mark on Camshaft Drive Gear
Pulley.
(3) Alignemnt Mark on Cylinder Head Cover LH.
6. Install crankshaft pulley temporarily and tighten
center bolt by hand (do not use a wrench).
Turn the crankshaft pulley clockwise to give some
belt slack between the crankshaft timing pulley
and the RH bank camshaft drive gear pulley.
2. Install pusher and tighten bolt to the specified torque.
Torque : 25 N·m (2.5 Kg·m/18 lb ft)
1. Install the pusher while pushing the tension pulley
to the belt.
2. Pull out pin from the pusher.
NOTE: When reusing the pusher, press the pusher with
approximately 100Kg to retract the rod, and insert a pin
(1.4 mm piano wire).
014RW011

Mar 18, 2009 | 2000 Isuzu Trooper

2 Answers

Need instructions to replace 1993 Toyota Camry Timing Belt


Hi Kmcarroll77

TIMING BELT REPLACEMENT - 2.2L -1993 Toyota Camry

Installation
1.Install No. 2 idler pulley (if removed). Install and tighten bolt to specification. See TORQUE SPECIFICATIONS . Ensure idler pulley is clean and rotates smoothly. 2.Install No. 1 idler pulley and tension spring (if removed). Pry No. 1 idler pulley away from timing belt area as far as possible. Temporarily tighten No. 1 idler pulley bolt. Ensure idler pulley is clean and rotates smoothly. 3.Using crankshaft pulley bolt, rotate crankshaft so timing mark on crankshaft sprocket aligns with timing mark on oil pump housing. See. This will position keyway in crankshaft sprocket at 12 o'clock position.

CAUTION:If reusing timing belt, ensure reference marks on timing belt align with reference marks placed on crankshaft and camshaft sprockets. Ensure timing belt is installed in original direction of rotation.
4.Ensure all sprockets and idler pulleys are clean. Install timing belt on crankshaft sprocket, oil pump sprocket, No. 1 idler pulley, and then No. 2 idler pulley in sequence. 5.Install timing belt guide with cupped side away from crankshaft sprocket and flat side toward timing belt. Install No. 1 timing belt cover and new gasket. 6.Align crankshaft pulley key groove with key in crankshaft. Install crankshaft pulley. Install and tighten crankshaft pulley bolt to specification. 7.Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover. If reusing timing belt, ensure reference mark on timing belt aligns with upper edge of No. 1 timing belt cover. 8.Rotate camshaft, and align hole in camshaft sprocket with alignment mark on camshaft bearing cap. See Fig. 2 . Install timing belt on camshaft sprocket. If reusing timing belt, ensure reference mark on timing belt aligns with the reference mark on camshaft sprocket. Ensure tension exists on timing belt between the crankshaft and camshaft sprockets.
CAUTION:DO NOT rotate crankshaft counterclockwise, as viewed from timing belt end of engine.
9.Loosen No. 1 idler pulley bolt 1/2 turn. Rotate crankshaft pulley 2 full revolutions clockwise from TDC to TDC. 10.Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover, and hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. See Fig. 2 . If timing marks are not aligned, remove timing belt and reinstall. 11.Rotate crankshaft clockwise 1 and 7/8 revolutions and align crankshaft pulley "0" mark with 45-degree Before Top Dead Center (BTDC) mark on No. 1 timing belt cover. See Fig. 5 . 12.Tighten No. 1 idler pulley bolt to specification. See TORQUE SPECIFICATIONS . Install No. 2 timing belt cover and gaskets. Install and tighten spark plugs to specification. 13.To install remaining components, reverse removal procedure. Install all bolts/nuts on right (timing belt side) engine mount before tightening to specification. 14.On Camry, when installing control rod and bracket on strut tower and right (timing belt side engine mount, tighten bolts to specification in sequence. See Fig. 6 . On MR2, tighten engine
b7619be.jpg
92cabaf.jpg
Hope this helps, don't forget to rate.

Lazaruselite

Feb 25, 2009 | 1993 Toyota Camry V6

Not finding what you are looking for?
1995 Mercury Tracer Logo

716 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

fordexpert

Level 3 Expert

5501 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...