Question about 1991 Ford F150

1 Answer

How do I remove the electrical connectors from the alternator

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 41 Answers

There should be one plug in type and one nut type. on the plug type push in on the back side of the plug and pull. You may need to use a flat head screwdriver. the nut type just use the right size tool.

Posted on Jul 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change the alternator on a 1991 amigo


Here are some steps that you need to do.
  • Disconnect battery ground cable at battery.
  • Remove drive belt.
  • Disconnect alternator electrical connector.
  • Disconnect battery positive cable nut on alternator.
  • Remove alternator
  • Put the new alternator
  • Connect the positive cable nut and electrical connector
  • Connect the battery ground cable
  • Start the car then check if its giving enough charge to your battery

Jan 02, 2011 | 1991 Isuzu Amigo

1 Answer

Alternator replace



Removal & Installation


NOTE There is a trend among manufacturers today to refer to the source of belt-driven electrical power as a -generator-; however, by virtue of the method in which the -generator- produces electrical current the device is actually an -alternator-. The two terms may be used interchangeably.

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:

    Negative battery cable Accessory drive belt Alternator upper mounting bolt Engine splash shield Radiator support access panel Rear alternator bracket from the engine Alternator mounting bolts Duct on the back of the alternator Electrical connectors Front alternator-to-A/C bracket Alternator

To install:
  1. Install or connect the following:

    Alternator Front alternator-to-A/C bracket. Torque the bolt to 37 ft. lbs. (50 Nm). Electrical connectors. Torque the battery connection nut to 115 inch lbs. (13 Nm). Duct on the back of the alternator Alternator mounting bolts. Torque the bolts to 37 ft. lbs. (50 Nm). Upper front bolt. Torque the bolt to 35 ft. lbs. (47 Nm). Rear bracket to the engine. Torque the bolt to 37 ft. lbs. (50 Nm). Radiator support access panel Engine splash shield Accessory drive belt Negative battery cable
  2. Refill the cooling system. 4 DeVille
    NOTE There is a trend among manufacturers today to refer to the source of belt-driven electrical power as a -generator-; however, by virtue of the method in which the -generator- produces electrical current the device is actually an -alternator-. The two terms may be used interchangeably.
  3. Before servicing the vehicle, refer to the Precautions Section.
  4. Drain the cooling system.
  5. Remove or disconnect the following:

    Negative battery cable Accessory drive belt Radiator Electrical connectors Alternator mounting bolts Alternator

To install:
  1. Install or connect the following:

    Alternator Alternator mounting bolts. Torque the bolts to 37 ft. lbs. (50 Nm). Electrical connectors. Torque the battery connection nut to 111 inch lbs. (12 Nm). Radiator Accessory drive belt Negative battery cable
  2. Refill the cooling system.


Dec 30, 2010 | 2004 Cadillac Deville

1 Answer

How do i remove an alternator on a 2000 caddilac seville sts


FIRST TURN OFF RADIO.REMOVE NEGATIVE BATTERY CABLE. REMOVE ACCESSORY DRIVE BELT.REMOVE THE COOLING FANS.REMOVE ALTERNATOR COOLER OUTLET HOSE.REMOVE ALTERNATOR COOLER INLET HOSE.REMOVE ELECTRICAL CONNECTORS.REMOVE ALTERNATOR MOUNTING BOLTS.REMOVE ALTERNATOR.PUT EVERYTHING BACK VISA VERSA TORQUE ALTERNATOR BOLTS 37 FT LBS.TORQUE ELECTRICAL CONNECTORS + BATTERY CONNECTION 115 INCH POUND,ALTERNATOR COOLER HOSE TORQUE 80 INCH POUNDS.

Aug 15, 2010 | 2000 Cadillac Seville

1 Answer

The battery and the alternator, need replacing on a 2006 6cyclinder, Taurus. I have the parts, and tools, I just never worked on a newer car before. I need a print out of instructions, please!!


Removal & Installation 3.0L (2V) To Remove:
  1. Disconnect the battery ground cable
  2. Remove the accessory drive belt
  3. Remove the fasteners and move the degas bottle aside.
  4. Disconnect the wiring from the alternator.
  5. Remove the brace and the alternator mounting bolt.
  6. Remove the alternator from the engine.
To Install:
  1. Install the alternator on the engine. Tighten the lower and right brace bolt to 18 lb-ft. (25 Nm) and the left brace bolt to 35 lb-ft. (48 Nm).
  2. Connect the wiring to the alternator.
  3. Install the degas bottle in the original position.
  4. Install the drive belt.
  5. Connect the negative battery cable.
3.0L (4V) To Remove:
  1. Disconnect the battery ground cable.
  2. Remove the accessory drive belt.
  3. Remove the power steering hose bracket nut from the alternator mounting bolt.
  4. Remove the upper alternator mounting bolts. NOTE: The left side bolt will come out with the alternator.
  5. Raise and safely support the vehicle.
  6. Remove the right front wheel.
  7. Remove the right inner fender splash shield.
  8. Remove the screws and the alternator splash shield
  9. Remove the torque converter inspection cover.
  10. Install the flywheel holding tool. holdingtool.gif
  11. Remove the bolt and the crankshaft pulley. NOTE: The crankshaft pulley bolt has a reverse thread. The crankshaft pulley and bolt are a molded composite and are one piece.
  12. Lower the alternator to allow access to the electrical connectors.
  13. Disconnect the crankshaft sensor.
  14. Release the oxygen sensor connector locator from the bracket.
  15. Remove the lower alternator bolt.
  16. Disconnect the regulator electrical connector.
  17. Disconnect the remaining wiring from the alternator and remove the alternator
To Install:
  1. Position the alternator on the engine while making the necessary electrical connections.
  2. Connect the voltage regulator electrical connector.
  3. Install oxygen sensor connector locator in bracket.
  4. Connect crankshaft sensor.
  5. Raise alternator and install upper alternator bolts (left side bolt is installed with alternator). Torque upper and lower bolts to 18 lb-ft. (25Nm).
  6. Position the wiring harness locator and install nut.
  7. Install the alternator splash shield and the screws.
  8. Position crankshaft pulley and install bolt (reverse thread). Torque to 74 lb-ft. (100Nm)
  9. Remove the flywheel holding tool.
  10. Install the inner fender splash shield.
  11. Install the right front wheel.
  12. Install the torque converter inspection cover.
  13. Lower the vehicle.
  14. Install the power steering hose bracket nut from the alternator mounting bolt.
  15. Install accessory drive belt.
  16. Connect the battery ground cable.
prev.gif next.gif

Jul 18, 2010 | 2006 Ford Taurus

1 Answer

I need a diagram on how to replace a 2001 chevy metro alternator.


2001 Chevrolet Metro 1.3L MFI SOHC 4cyl

Alternator - Removal & Installation
  1. Before servicing the vehicle, refer to the precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Air cleaner assembly Alternator electrical connectors Accessory drive belt Upper and lower mounting bolts Alternator
To install:
  1. Install or connect the following:
    Alternator and the bolts, do not tighten the bolts at this time
  2. Install the alternator belt and adjust the tension until a deflection of 0.24-0.31 inch (6-8mm) deflection with 22 lbs. (10 kg) of pressure exerted when installing a used belt. On a new belt the belt deflection should be 0.20-0.27 inch (5-7mm) with 22 lbs. (10 kg) of pressure exerted.
    Alternator electrical connectors, then torque the alternator bolts to 17 ft. lbs. (23 Nm) Air cleaner assembly Negative battery cable
  1. Before servicing the vehicle, refer to the precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Accessory drive belt Alternator electrical connectors Alternator
To install:
  1. Install the alternator and hand-tighten the bolts.
  2. Install the alternator belt and adjust the tension until a deflection of 0.24-0.31 inch (6-8mm) deflection with 22 lbs. (10 kg) of pressure exerted when installing a used belt. On a new belt the belt deflection should be 0.20-0.27 inch (5-7mm) with 22 lbs. (10 kg) of pressure exerted.
  3. Install or connect the following: Upper alternator bolt to 18 ft. lbs. (25 Nm) Lower alternator bolt to 40 ft. lbs. (54 Nm) Alternator electrical connectors Accessory drive belt Negative battery cable

    459fdba.jpg
    Fig. Exploded view of the alternator-Metro and Prizm models
Hope thats help (remember rated this).

Feb 18, 2010 | 2001 Chevrolet Metro

1 Answer

Remove and replace alternator


2000 Ford Truck Expedition 4WD 4.6L EFI 8cyl

Alternator - REMOVAL & INSTALLATION

4.2L Engine

  1. Disconnect the negative battery cable.
  2. Disconnect 2 alternator and voltage regulator electrical harness connectors at the alternator. To disconnect push-on type terminals, depress the lock tab and pull straight off.
  3. Remove the positive battery cable nut and remove the positive battery cable at the alternator.
  4. Rotate the drive belt tensioner away from the drive belt and remove the drive belt from the alternator pulley.
  5. Remove 3 alternator retaining bolts and remove the alternator.
To install:
  1. Place the alternator on the engine and install 3 alternator retaining bolts. Tighten the bolts to 18-22 ft. lbs. (20-30 Nm).
  2. Rotate the drive belt tensioner away from the drive belt and install the drive belt on the alternator pulley.
  3. Connect 2 alternator and voltage regulator electrical harness connectors.
  4. Connect the positive battery cable to the alternator and install the nut and washer. Tighten the nut to 84 inch lbs. (10 Nm).
  5. Connect the negative battery cable.
  6. Start the engine and check for proper charging system operation.
4.6L, 5.4L and 6.8L Engines

f52fc60.jpg

Fig. 1 Detach the connectors from the alternator

ffe1937.jpg

Fig. 2 Remove the nut and the battery cable from the post on the rear of the alternator

6ce39ae.jpg

Fig. 3 Remove the 2 front alternator mounting bolts and ...

45a032e.jpg

Fig. 4 Remove the alternator from the engine by carefully lifting it up and...

6513790.jpg

Fig. 5 ... out of the engine compartment
  1. Disconnect the negative battery cable.
  2. Rotate the drive belt tensioner away from the drive belt and remove the drive belt from the alternator pulley.
  3. Detach the electrical harness connectors at the alternator assembly.
  4. Disconnect the positive battery cable and remove the nut and washer.
  5. Remove 2 front alternator bolts.
  6. Remove the rear alternator support bracket retaining bolts and the support bracket.
  7. Remove the alternator from the vehicle.
To install:
  1. Place the alternator in position and loosely install 2 front alternator retaining bolts.
  2. Install the alternator bracket and 3 alternator bracket bolts. Tighten to 84 inch lbs. (10 Nm).
  3. Tighten 2 front alternator retaining bolts to 19 ft. lbs. (26 Nm).
  4. Connect 2 electrical harness connectors to the alternator assembly.
  5. Connect the positive battery cable and install the nut and washer. Tighten the nut to 72 inch lbs. (8 Nm).
  6. Rotate the drive belt tensioner away from the drive belt and install the drive belt on the alternator pulley.
  7. Connect the negative battery cable.
  8. Start the engine and check for proper charging system operation.
5.8L and 7.5L Gasoline Engines and 7.3L Diesel Engine
  1. Disconnect the battery ground cable.
  2. Label and detach the connectors from the alternator.
  3. Release the tensioner and remove the drive belt from the alternator pulley.
  4. Remove the alternator retaining bolts.
  5. Remove the alternator from the vehicle.
To install:
  1. Position the alternator and install the retaining bolts. Tighten the retaining bolts to 15-21 ft. lbs. (21-29 Nm).
  2. Install the drive belt.
  3. Attach the alternator connectors.
  4. Connect the battery ground cable.

I really hope help you with this (remember rated this help) Good luck.

Oct 13, 2009 | 2000 Ford Expedition

2 Answers

How do I change a 2005 mustang alternator? NOT gt


2005 Ford Mustang 4.0L SFI SOHC 6cyl
Ford Mustang 1999-2005
Alternator - Removal & Installation

3.8L And 4.0L Engines
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Disconnect the negative battery cable.
  3. Remove the accessory drive belt.
  4. Disconnect the alternator electrical connectors.
  5. Remove the alternator shield (4.0L engine).
  6. Remove the alternator mounting bolts.
  7. Remove the alternator from the vehicle.
  8. Installation is the reverse of the removal procedure.
To install:
  1. Position the alternator onto engine. Tighten the lower bolt to 35 ft. lbs. (47 Nm) and the upper bolt to 18 ft. lbs. (25 Nm).
  2. Install the alternator shield (4.0L engine).
  3. Connect the alternator electrical connectors.
  4. Install the accessory drive belt.
  5. Connect the negative battery cable.

4.6L Engines (Non-Supercharged)
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Disconnect the negative battery cable.
  3. Remove the air intake scoop bracket, if equipped.
  4. Remove the accessory drive belt.
  5. Remove the upper alternator bracket.
  6. Disconnect the alternator electrical connectors.
  7. Remove the alternator bolts.
  8. Remove the alternator from the vehicle.
  9. Installation is the reverse of the removal procedure.
To install:
  1. Position the alternator onto engine. Tighten the mounting bolts to 18 ft. lbs. (25 Nm).
  2. Connect the alternator electrical connectors.
  3. Install the upper alternator bracket. Tighten the bolts to 89 inch lbs. (10 Nm).
  4. Install the accessory drive belt.
  5. Install the air intake scoop bracket, if equipped.
  6. Connect the negative battery cable.
4.6L Engines (Supercharged)
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Disconnect the negative battery cable.
  3. Remove the accessory drive belt.
  4. Raise the vehicle.
  5. Disconnect the alternator electrical connectors.
  6. Remove the alternator bolts.
  7. Remove the alternator from the vehicle.
  8. Installation is the reverse of the removal procedure.
To install:
  1. Position the alternator onto engine. Tighten the lower bolt to 18 ft. lbs. (25 Nm) and the upper bolt to 37 ft. lbs. (50 Nm).
  2. Connect the alternator electrical connectors.
  3. Lower the vehicle.
  4. Install the accessory drive belt.
  5. Connect the negative battery cable.
  6. Installation is the reverse of the removal procedure.

More details about this model in Autozone.com (free register).

I hope help you with this (remember rated this help). Good luck.

Sep 17, 2009 | 2005 Ford Mustang

1 Answer

Alternator removel on a 95 mitsubishi diamante


3.0 SOHC. TURN OFF RADIO. THEN DISCONNECT BATTERY NEGATIVE CABLE.REMOVE AIR CLEANER ASSEMBLY.LOOSEN THE TENSIONER PULLEY.REMOVE ALTERNATOR DRIVE BELT .REMOVE ACCELERATOR CABLE.REMOVE.BRAKE BOOSTER VACUUM HOSE.REMOVE EGR VALVE.REMOVE ALTERNATOR ELECTRICAL CONNECTORS. THEN REMOVE MOUNTING BOLTS THEN REMOVE ALTERNATOR. THE 3.0 DOHC DISCONNECT NEGATIVE BATTERY CABLE.REMOVE SURGE TANK.REMOVE AIR DELIVERY HOSES TO GAIN ACCESS TO THE ALTERNATOR .IF YOU HAVE AIR CONDITIONER .REMOVE THE CLAMP .RAISE THE SUCTION HOSE.USE SOMETHING TO HOLD IT OUT OF THE WAY.LOOSEN TENSIONER PULLEY .AND REMOVE THE ALTERNATOR DRIVE BELT .DISCONNECT THE OXYGEN SENSOR CONNECTOR .DISCONNECT THE ALTERNATOR ELECTRICAL CONNECTORS.REMOVE ALTERNATOR BRACKETS AND MOUNTING BOLTS .REMOVE THE BRACKET AND ALTERNATOR AS A ASSEMBLY.SEPARATE THEM ON A WORK TABLE.

Jul 05, 2009 | 1992 Mitsubishi Diamante

2 Answers

How do i remove the alternator in a 2001 sebring convertible?


2.7L Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:

    Negative battery cable from the shock tower Accessory belt splash shield and loosen the belt Alternator electrical connectors A/C pressure switch and clutch electrical connectors Engine oil dipstick Alternator

To install:
  1. Install or connect the following:

    Alternator and torque the bolts to 40 ft. lbs. (54 Nm) Engine oil dipstick tube A/C pressure switch and clutch electrical connectors Alternator electrical connectors Drive belt and splash shield Negative battery cable

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Raise vehicle and support.
  3. Remove the accessory drive belt splash shield.
  4. Loosen the accessory drive belt.
  5. Remove the lower mounting bolt.
  6. Lower the vehicle.
  7. Remove the electrical connections from the alternator.
  8. Disconnect the electrical connector to the A/C pressure switch and A/C clutch.
  9. Remove the engine oil dip stick.
  10. Remove the 2 upper mounting bolts.
  11. Remove the alternator.

To install:
  1. Install the alternator.
  2. Install the 2 upper bolts, but do not tighten.
  3. Install the engine dip stick tube.
  4. Connect the A/C pressure switch and A/C clutch electrical connectors.
  5. Connect the electrical connections to the alternator.
  6. Raise vehicle and support.
  7. Install the lower bolt. Tighten bolt to 40 ft. lbs. (54 Nm).
  8. Install the accessory drive belt.
  9. Install the accessory drive belt splash shield.
  10. Lower the vehicle.
  11. Install the 2 upper mounting bolts. Tighten bolts to 40 ft. lbs. (54 Nm).
  12. Connect the negative battery cable.

Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

Apr 28, 2009 | 2001 Chrysler Sebring

Not finding what you are looking for?
1991 Ford F150 Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...