Question about 2007 Hyundai Sonata Limited Sedan

1 Answer

I need to remove front r/side studs on 2005 hyundai elentra 4 dsd?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 382 Answers

Dear friend-replacing the stud is a fairly intensive job,the hub must be removed,so you might have to replace the wheel bearing,you will need special tools to attemp this job.

Posted on Jul 21, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hyundai elentra bent frame and door handle


No way to tell without looking at it and taking measurements.
It may be cheaper to replace the doors than to spend the time on repairs.

Sep 05, 2012 | 2010 Hyundai Elantra

1 Answer

How to change the p2251 o2 sensor on 2005 hyundai elentra


I've supplied a generic tutorial on how to replace an oxygen sensor. It should take you from 15-30 minutes even less if there is little or no rust.

May 30, 2012 | 2005 Hyundai Elantra

2 Answers

I have broken lugs on my 2004 Hyundia Santa Fe. I am trying to pull the front left hub off using a puller (3 jaw). The puller is pushing the axel back. I called the local dealer. The Mechanic said I...


You should be able to hammer out the wheel studs
if you have clearance
You shouldn't have to pull the entire bearing assy

Look on YOU TUBE there are all kinds
of videos of hub replacements

You remove the axle nut & 3 or 4 bolts
holding the bearing assy,that is all
The axle stays in place
There is no puller involved

Mar 10, 2011 | Hyundai Santa Fe Cars & Trucks

2 Answers

Location of fuel filter on 2005 hyundai elantra


check right under the rear end of your vehicle body near the fuel lines

Dec 07, 2009 | 2005 Hyundai Elantra

1 Answer

The front drivers side window on my 2005 Hyundai Elentra was working fine last night i rolled it down on my way to church and it got stuck and will not roll up. It appears to be off the track. Could you...


Sounds like the window regulator has malfunctioned. Best solution: Take your vehicle to an authorized Hyundai dealership and pay the diagnostic fee... they will tell you exactly what the problem is and the cost of parts/labor to fix it... at least this way you'll know what the problem is and what's required to fix it.

Oct 25, 2009 | 2005 Hyundai Elantra

2 Answers

Need to replace wheel stud on hyundai sonata, how?


have a 2005 hyudai tucson can't remove the front studs even though we pulled off the brakes and caliper but still not enough room to put in new studs and i can't dissasemble it any further

Aug 15, 2009 | 2002 Hyundai XG350

1 Answer

Front wheel stud broke off


Knuckle needs to be removed and the center hub 'pressed out' using a hydraulic press (accepted procedure). You can avoid this by using an air hammer and disk cutting tool to remove the old stud, then trim the 'stop flange' on the new stud (1/4 moon cut) in order to install it.... however, you gotta know what you're doing so you don't compromise the integrity of the new stud.

Jul 04, 2009 | 2002 Hyundai XG350

1 Answer

PETROL FILTER LOCATION


Hi,

I am assuming you would want to know the placement of the fuel filter. It actually depends if your Elentra is a Sedan or Wagon.
To my knowledge a 99 Hyundai Elentra has an inline fuel filter. It is located in the engine bay right against the firewall. It could either be on the driver side or the passenger side. It looks like a small canister with tubing connectors at the top and bottom. It is normally held by a clamp.. It maybe necessary to remove the air filter box to have easy access on removal of the fuel filter. It is a sound practice to relieve the fuel pressure prior to fuel filter removal.

If on the other hand, you are seeking locations where you can purchase a fuel filter for your 1999 Elentra, pls try here, here, here or even eBay for a start.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.

Thank you for using FixYa.

Jul 11, 2008 | Hyundai Motor 1999 Elantra

Not finding what you are looking for?
2007 Hyundai Sonata Limited Sedan Logo

213 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...