Question about Subaru Outback

1 Answer

Hi my subaru out back have ben miss firing start when I change the front catalitic the catalitic bloo op and the engene start to roning rely bad lather I change the ignairer is lokeired on the fire woll of the car now I replace the coil pack and estill no roning olso y put to new oxigen sensors and secont cat I spent to mush mony and not result. are no wat ?I can do now please if you can help me aout I ben reale please tanks Omar Note : SUBARU OUT BACK 1998 2.5L for cams

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Check your


exhaust pipe not proper tight or have hole

Posted on Jul 12, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

1999 chevy silverado miss firing

When you change the crank sensor you need a scan tool to set them.The distributor has to be turned using a scan tool to get the crank sensor dialed in.

Jan 09, 2012 | 1999 Chevrolet Silverado 1500

1 Answer

2001 Legacy Wagon Idles rough and has no power when in gear. Changed all the plugs, changed the exaust sensor. Check engine light still on after all that.

1 you need to get the code. 2 sounds like the catalitic converter is bad. If the code was for the exhaust sensor, the catalitic converter will pop this code.

May 24, 2011 | 2001 Subaru Legacy

1 Answer

Engine hestitation, 2000 subaru forester

I think these codes are indicating a fault with your catalytic converter. The 02 sensors are each not returning the correct values to the ECM, causing a "suspect the 02 sensors" fault code.

Apr 01, 2010 | 2000 Subaru Forester

1 Answer

Missing while idel

It is probably a bad coil, have someone put it on a computer and see what cylinder is missing. The coils go bad all the time on the 5.4's

Dec 22, 2008 | 2007 Ford F-250 Super Duty Lariat

1 Answer

My check engine light blinks 12 times

not sure about the 12 times one but i know the blinking then staying on and missing then shut it off and changing the sensor and it running ok when you start it.... thats because your catalitic converter is cloged, usually from miss fires or bad/old plugs/wires you need to replace your cat cause its beyond repair and make sure to change your plugs and wires (and i would do my fuel filter and air filter while i was at it if it were me) or else you will have the same problem right around the corner. I know this due to the fact it happened to both my parents cars and when i bought my truck with 103000 miles the guy before me NEVER changed his stuff, (supposed to do plugs and wires at 12000 mile intervales) and it was all factory, Hope this helps.

Jul 25, 2008 | Jeep Cherokee Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

194 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts


Level 3 Expert

83850 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22413 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides