Question about 2000 Nissan Quest

1 Answer

Cruise control vacumm hose not connected

Cannot find where to connect vacuum hose to engine

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 35 Answers

Check around the intake area, The cruise control vacuum should be connected near the intake of the engine.

http://store.payloadz.com/str-asp-i.148379-n.2005_NISSAN_QUEST_WORKSHOP_SERVICE_REPAIR_MANUAL_eBooks_-end-detail.html is a link to purchase the manual for the vacuum line routing

Posted on Jul 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

On/off button for cruise control quit working. Fuse is good, what else could be the problem?


Some of these cruise control devices rely on vacuum pressure from a small hose connected between the engine intake (vacuum source) and a cup-like vacuum enclosure and diaphragm with a connection to hold / adjust the throttle position to maintain vehicle speed. A cracked hose is all that is needed to cause the system to fail. This is especially true if your have a newer car and the "check engine" or "service engine soon" light is on.

Oct 20, 2015 | Cars & Trucks

2 Answers

The cruise control in my 1989 305 v-8 pontiac firebird doesn't stay engaged. it will hold cruise , but after a few miles , it disengages.


The older vehicles used vacuum to control the Cruise. Check for a leak in the vacuum system. Using a can of starting fluid, spray the vacuum lines and fittings lightly. If the engine revs up after a spray, it'e most likely the leak.

Aug 24, 2011 | 1989 Pontiac Firebird

1 Answer

My cruise control will not maintain a stady speed


Cruise controls use Vacuum from the engine inlet manifold to operate the throttle linkage when cruising is engaged. If the hose that supplies the vacuum is not tight on the connections at either end, due to getting hard and/or splitting, the unit will not have enough vacuum to operate the linkage or in your case not maintain set speed. Check the hose that supplies vacuum to the cruise control, as well as all the hoses used for pollution control where they attach to the various pipes in the engine bay, for poor connections. They should be tight, not hard or split and not be able to be removed easily.

Nov 14, 2010 | 1997 Toyota T100

1 Answer

The cruise control doesn't work but the light cruise is on in the panel and the actuator have been change. The fuse is also looking good but i'm wondering if any relay or other switch could be in cause?...


Cruise controls use Vacuum from the inlet manifold to operate the throttle linkage for cruising. If the hose that supplies the vacuum is not tight on the connections at either end, due to getting hard and/or splitting, the unit will not have enough vacuum to operate the linkage. Check the hose that supplies the cruise control, as well as all the hoses used for pollution control in the engine bay for poor connections. They should be tight, not hard or split and not be able to be removed easily.

Sep 23, 2010 | 2003 Toyota Highlander

1 Answer

My cruise controll has stopped working and my dashboard lights have stopped working also. All of my idiot lights work including the turn signals. I just cant see the speed at night! Please help


The Dashboard light dimmer control is probably stopped working because one of the tiny eletronic bits inside it has died. A temporary fix is to remove the connecting plug on the rear of the unit and put a bridging wire across the terminals. The cruise control problem could have several causes. They operate on engine vacuum so check the hose going to the cruise control unit in the engin bay from the inlet manifold. If the hose is cracked or hard there will not be enough vacuum to operate the cruise control.

Aug 18, 2010 | 1999 Ford Crown Victoria

1 Answer

1994 jaguar xjs 4.0----need to know where the vacumm line that feeds vac to cruise control eminates from--yea i know, from the engine----but where ,specifically, on the engine ?????


On my 90 and 92, I have a vacuum line from the driver side intake manifold at about inline with the # cylinder. It travels to the firewall between engine and firewall to a connection underneath the battery.That line goes through the firewall and connects to other lines roughly above your feet if you are sitting in the passenger side of the car.

Jun 10, 2010 | 1994 Jaguar XJ6

1 Answer

My 2004 jetta cruise control is not working. I have changed both the brake switch and the clutch switch and I checked all the fuses. What else could it be?


Engine vacuum does the work for most cruises. Check the vacuum hose that goes to the cruise control servo and ensure it has no cracks and is connected well. Also check the hose that connects up under your air filter.

Apr 09, 2010 | 2004 Volkswagen Jetta

2 Answers

I have a 2001 ford escape and the cruise control does not work the indicator light comes on but it will not set


I had the exact same problem on my 2002 Escape. If you remove the engine cover (3 bolts), you will see where the cruise control links to the the throttle body. If your problem is the same as mine, you will see that it is not connected. I believe it is intended to snap on, but it just doesn't stay. I temporarily snapped it in and wrapped electrical tape to prevent it from unsnapping. Worked like a charm.
Hope this helps.

Jul 16, 2009 | 2001 Ford Escape

3 Answers

2003 jeep grand cherokee cruise control not working.


Ok, the '03 Jeep Grand Cherokee uses a small vacuum line to control the servos. Since your light comes on, it's obviously getting power. 9 out of 10 times it's the vacuum hose.
Pop the hood and look on the passenger side towards the back for the engine coolant reservoir. It's most likely underneath it so you may have to remove the res. Check the vacuum hose and all vac. connections then check the electrical connections. If that's not the problem, check the cruise control connection to the throttle linkage.
If that still doesn't do it, you may need use scan tools and diagnostic procedures that are out of the scope of home mechanics.
Wish ya luck!

Jun 18, 2009 | 2003 Jeep Grand Cherokee

1 Answer

I have a 1997 cherokee country 6 cyl. 4.0L, and my cruise control will not work I dont know what it is?


Cruise control works from engine vacuum. Check for leaks where vacuum hoses connect to inlet manifold and vacuum canister behind front bumper for damage or leaks.

Feb 14, 2009 | 1997 Jeep Cherokee Country

Not finding what you are looking for?
2000 Nissan Quest Logo

Related Topics:

206 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

Marvin
Marvin

Level 3 Expert

81342 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...