Question about GMC Jimmy

1 Answer

How do i put on the serpintine belts - Jimmy GMC Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 218 Answers

You will have to locate the belt tensioner ( if this has a serpentine belt setup) just put a wrench on the bolt where the pulley is and turn until you release the slack on the belt (this is spring loaded) remove the belt (be sure to note how the old belt was on before removing it) position the new belt in place, turn the tensioner once again and position the new belt, the release the tensioner. Hope this helps

Posted on Jul 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000cadilac devile just replaced serpintine belt now car wont start ,just clicks..take off serpintine belt and will start r i ght u 0 what could it be???


Most likely one of the things that the belt drives is frozen. Check that your water pump, power steering pump, alternator, etc all turn without the belt.

Apr 02, 2018 | Cars & Trucks

1 Answer

Hw to put on a serpintine belt on a 2002 crown vic


there is a hole in the tensioner that you can put a ratchet in and take the tension off of the belt ,You can than easily replace the belt

Sep 04, 2014 | 2002 Ford Crown Victoria

1 Answer

Volvo s80 t6 after putting my serpintine belt back on when i started the car a good size of the belt ripped of and wrapped around my harmonic balncer to the timming belt and shut my car right down


Did the piece of serpentine belt actually make contact with the timing belt ? The timing belt should have been behind the timing cover.
And does the engine crank normally ? Normal compression ?

Jan 24, 2014 | 1999 Volvo S80

1 Answer

Replace serpintine belts on 2002 mazda millenia 2.5l


is it the one belt or does it have the 3 belts

Dec 28, 2012 | 2002 Mazda Millenia

1 Answer

Cant put serpintine belt on


You don't take anything off

You just put a long 1/2" ratchet in the hole on
the tensioner & Pull against the spring tension until
you have the belt over the final pulley

Oct 12, 2012 | 2000 Buick LeSabre

1 Answer

Alternator


First you need to remove the serpintine belt or alternator belt. If it is a serpintine locate the tension pully(the one that doesn't look like it does anything) place a wrench over the pully bolt and pull while removing the belt. Most generaly all alternators have two bolts holding them in. Remove both bolts. and remove alternator on some vehicles you need to remove the top engine mounts to remove the acctual alternator. make sure you if you do this you put a jack under the bngine block. NEVER ON THE OIL PAN. After that simply remove the old alternator and replace it with the new one reinstall the serpintine belt as instructed on either the underside of your hood or where the hood latch is.

Apr 10, 2010 | 1993 Toyota Corolla

1 Answer

1990 v6 serpintine belt diagram


for the most part there is a diagram under the hood showing you how the belt goes back on what i do is draw me a diagram before i take the old off and if you have a autozone near you they will print you one off for free if you do not have one under the hood.

Apr 17, 2009 | 1994 Chrysler LeBaron

1 Answer

Diagram instalation for serpintine belt


you can go to www.autozone.com and on the main page click on repair manuals and go from there and should show you in there.

Dec 20, 2008 | 1993 Lincoln Continental

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

185 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...