Question about 1999 Honda Accord

1 Answer

Indicator lights saty on.

My battery, brake, all 4 doors, truck, and brake lamp lights stay on. They started flashing on and off while driving trough really bad rain storms for hours last last, and then just stayed on. I let the car sit over night, and checked the fuses. That did not help. Do you think it could be a belt?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 218 Answers

A belt wouldn't cause all those lights to come on, If you were driving through a lot of water like you stated, it might have shorted out the Body Control Module, would recommend taking to a repair shop or the dealer to have this repaired. Hope this helps

Posted on Jul 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2010 eqinox, abs warning lamp came on and all wheel drive off indicator came on.


Get the trouble codes read. That's ALWAYS the starting point.

Aug 26, 2017 | Cars & Trucks

1 Answer

How do I fix my 99 blazer the dome lights won't turn on and the 4 who drive won't light up or work


In the instrument panel fuse box fuse # 8 CTSY LP 10A ,that's for the dome lights, fuse panel is left side of IP. What are you talking about 4 who drive won't light up or work ? 4 wheel drive ? Do you have two speed automatic or two speed selectable ?
Switch Indicator Lamps Do Not Light - One or More ? Check fuse #15 IP fuse box 10A 4WD . This is for two speed auto !

Circuit Description

The indicator lamps circuits consist of 5 individual lamps contained inside the mode/range switch assembly, they are AUTO, 4WD, 2HI, 4HI, 4LO and NEUTRAL. The AUTO, 4WD, 2HI, 4HI, and 4LO lamps are contained inside their respective range button. When the ignition is ON, the transfer case shift control module illuminates the indicator lamp that corresponds to the current ATC gear position by providing a ground through a current limiting driver.
The transfer case shift control module flashes each indicator lamp after a shift has been requested and will continue to flash until the transfer case shift control module can complete the shift. After a shift to AUTO, 4WD, 2HI, 4HI, or 4LO is made, the transfer case shift control module will flash that indicator lamp until the transfer case shift control module receives a high voltage signal on CKT 1695 from the front axle switch.
A solid state circuit located inside the switch supplies ignition voltage to the lamps. The solid state circuit also receives voltage whenever the headlamp switch is in park or headlamp position. When the solid state circuit receives voltage from the headlamp switch it will reduce the voltage that it supplies to the indicator lamps, dimming the lamps when the headlamps are ON.

Feb 07, 2015 | Cars & Trucks

1 Answer

How do i fix cruise control on 2000 ford excursion


TRY THIS Self-Test Diagnostics - Excursion.
[img src="file:///E:/FORD/ELECTRICAL/Speed%20Control%20Workshop%20Manual_files/SYOusenfileani_caut.gif" border="0"> WARNING: This test is a key on engine off (KOEO) test only that is conducted in park only with emergency brake fully engaged.

  1. Enter Self-Test Diagnostics by depressing the speed control OFF switch while turning the ignition key ON, making sure the engine does not start and is not running. The speed control indicator on the instrument panel will flash once to indicate that speed control module entered the diagnostic mode. FIVE ADDITIONAL FLASHES AT THIS POINT INDICATE A DEFECTIVE SPEED CONTROL SERVO. Release the OFF switch.
  2. Press the remaining switches in this sequence: ON, RESUME, COAST and SET/ACCEL.
    IF THE "ON" SWITCH IS NOT DEPRESSED WITHIN FIVE SECONDS AFTER ENTERING THE DIAGNOSTICS MODE, THE MODULE TIMES OUT AND THE PROCEDURE MUST BE STARTED OVER.
    The speed control indicator lamp will flash as each switch is depressed. Press each switch in the sequence immediately after the indicator light goes out for the previous switch.
  3. A lamp flash with the last button (SET/ACCEL) indicates that the STATIC test passed. If the lamp does not flash with the last button and there are no additional flashes of the lamp, the switch is defective.
    If the lamp does not flash with the last button, and additional flashes occur, follow the chart below for trouble codes:
    * 2 Flashes - BPP defective, circuit is defective, brake applied, CPP switch or jumper (if equipped).
    * 3 Flashes - Deactivator switch is open or circuit defective.
    * 4 Flashes - Vehicle speed signal is out of range or circuit is defective.

  4. Immediately after the STATIC test, the speed control servo does a DYNAMIC test by automatically actuating the throttle lever from 8 mm (0.315 in) to 12 mm (0.472 in) of travel from the idle position. During the DYNAMIC throttle pull, observe throttle movement to witness any binding or sticking of the speed control cable and correct connection of speed control cable to throttle lever. Make sure the THROTTLE RETURNS BACK TO IDLE POSITION.
  5. Return ignition switch to the OFF position

NOTE:
I had it replaced by ford dealer free of charge CHECK FACTORY RECALLS USING YOUR VIN if u don't know how send it to me and i will check it for you it is located at the inner side of the driver door frame.

Apr 26, 2014 | 2000 Ford Excursion

1 Answer

Abs light stays on and the esc indicator light also but when you start it it shows it off


the operators guide shows what these mean and what to do.
lost that>? i have one, and 08 JK.
pages 105 to 116
it resets each drive. the opr guide says that, and does.
its a very complex system, you should RTM.

ill quote your missing pages.
ABS:
If the light remains on after start-up or comes on and
stays on at road speeds, it may indicate that the ABS has
detected a malfunction or has become inoperative. The
system reverts to standard non-anti-lock brakes.
ESP:/TCS
The ESP/TCS Indicator Light (located in the instrument
cluster), starts to flash as soon as the tires lose traction
and the ESP system becomes active. The ESP/TCS Indicator
Light also flashes when TCS is active. If the
ESP/TCS Indicator Light begins to flash during acceleration,
ease up on the accelerator and apply as little throttle
as possible. Be sure to adapt your speed and driving to
the prevailing road conditions


is this clear? if not ask more, questions , more specific and we can peel the onion deep as you want.
also wiki this topic, to understand it ...

Mar 08, 2014 | 2007 Jeep Wrangler Unlimited Rubicon 2...

1 Answer

2004 Dodge Durango electrical issue


the problem started because the battery was disconnected
try using a scan tool to reset the ECM program

Apr 29, 2017 | 2004 Dodge Durango

1 Answer

4x4 indicator flashing all the time wnen not engaged


2001 Mitsubishi MONTERO 01 - Transfer Case > POWER TRAIN : TRANSFER CASE (4-WHEEL DRIVE) [Part 104000 ]
TSB No: 0223007 NHTSA ID: , November 01, 2002 : Replacement:
Summary: 4wd indicator lamp flashing / diagnostic trouble code (dtc) 33.

2001-02 Montero
A flashing 4WD indicator lamp and/or DTC 33 may be caused by corroded transfer case shift position switches. The original switches are susceptible to water damage, and new revised switches are available to prevent the problem.

PROCEDURE

1. Replace the five transfer switches

2. Clear the DTC, using the scan tool.

3. Test drive the vehicle to confirm the 4WD indicator lamp does not flash and DTC 33 does not reset.

Apr 08, 2009 | 2001 Mitsubishi Montero

1 Answer

Maintenance light and brake lamp light what does it mean


The Maint Req Light is only a reminder light to get the Oil changed and fluids checked and what nots.. Its on a timer that must be reset.. Its no big deal if ya had it seviced recently.. Heres how to turn it off: 1) Make sure Key is Off 2) Press and Hold Mileage reset button. 3) While Holding Milelage Reset button, swicth car to run, but dont crank..4) Continue to hold button until light flashes and goes off.. then switch it off .. Start the engine to make sure it worked.. Sometimes ya gotta do it twice.. NOW.. And ur Lamp indicator.. Means you probably have a brake light or turn signal bulb out on the rear.. Get someone to help ya look for that.. Lemmie know if this works.. and Take care.. Thanx

Mar 11, 2009 | 2001 Acura 3.2TL

1 Answer

Battery and brake indicator light stays on after start


When the lights are on check the battery voltage. Should be 13.0 to 14.5. If you unplug the connector on the alternator when the lights are on, do they go off?

Mar 11, 2009 | 1994 Nissan Pickup

2 Answers

Emergency brake pedal will not stay down when i press it.


The parking brake actuator (the mechanism you press with your foot) works like a ratchet wrench. The pedal has a cresent shaped plate with teeth on it. It pivots on a mounting plate. There is a pawl with a small spring also on the backing plate. This pawl engages the teeth on the pedal assembly to hold the brake engaged (against the large return spring).
Stick your head under the dash and look carefully at the parking brake actuator mechanism. See why the pawl is not engaging the teeth on the pedal assembly. Most likely causes are that the release mechanism is jammed "on" or that the light spring which attaches to the pawl is missing (usually from being kicked by some one with large feet) View this mechanism on another GM vehicle with the same style parking brake if you suspect that parts are missing.
Charlie

Dec 07, 2008 | 2002 Chevrolet Blazer

Not finding what you are looking for?
1999 Honda Accord Logo

172 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...