I couldn't find my spare key to my Subaru I so I figured I would just drill out the ignition because I still have my key fob but i finally found my key and nownmy ignition won't turn. please help asap

Have a key fob? if so, lock it down. Open it with the fob. This should disable security.

Could be the battery in the key fob is flat? try a new battery.

This model year comes equipped with Keyless Enter-N-Go, which uses an electronic transmitter in the key fob to communicate with the car. The vehicle's doors will not unlock and the vehicle will not start if the key fob is not matched to the vehicle or if the commonly-available watch battery in the key fob has been depleted. The EVIC will flash a message upon vehicle startup if it determines that the battery in your key fob is low on charge and should be replaced.

To open the doors, try the following:

1. Use the spare key fob that came with the vehicle. If the battery in your main key fob is depleted, the spare key fob's battery may still retain charge due to its much more occasional use.

2. The key fob comes with an emergency key inside of it. To remove the emergency key, slide the mechanical latch on the back of the key fob sideways with your thumb and then pull the key out with your other hand. This key will allow you to unlock the driver's side door and glove compartment. It will not start the vehicle.

To start the car with a severely-depleted key fob battery, try the following:

1. In case the ignition switch does not change with the push of a button, the RKE transmitter (Key Fob) may have a low or dead battery. In this situation a back-up method can be used to operate the ignition switch. Put the nose side (side opposite of the emergency key) of the Key Fob against the ENGINE START/STOP button and push to operate the ignition switch.

To replace the battery in your key fob, try the following:

1. Remove the emergency key from the key fob following the directions above.

2. Using a vinyl spudger tool or a flat-bladed screwdriver, gently pry the two halves of the key fob apart at the indented slot above the slot for the emergency key.

3. Replace the depleted battery with a new battery. Use the depleted battery to visually match the size. The battery is usually available wherever watch or hearing-aid batteries are sold.

4. Snap the key fob back together and replace the emergency key. If the issue is a depleted battery, your key fob should operate normally.

If the issue is not related to the state of the battery, you will probably need to contact your local dealer for service.

Source: Owner's Manual, pages 12-17

http://justgivemethedamnmanual.com/dodge/dodge-charger-owners-manual/

in what way do you mean. is the remotes not working or are they another set? original set you turn key in ignition to number 2 and press the fob. (remote) then the doors should lock press again to unlock and turn key back to 0 and try fob again do this for both. make sure the batteries are new in the fob's. leave ignition off for 3 min before doing the other one.

If you are talking about the Key FOB, most Autozone, Advance, and Oreilys have a remote tester and batteries for the FOB.

Please rate my info.

Your key is the kill switch. If you don't have a fob you can just put the key in the ignition and turn it back and forth several times (without starting the car) to turn alarm system off.

Close the doors. Lock the doors using the buttons on the key fob. Use the fob to again unlock the doors. The key should then work the ignition. If this will not work, you will have to tow your vehicle to the dealer and buy a new key and/or fob and have it programmed to the vehicle.

You do not change the battery as it is re-chargeable. It is charged in the key fob unit while it is in the car's ignition and while you are driving the vehicle.

If you have a spare key that has low battery power then it needs to be used in the vehicle to charge the battery.

If you have been using the key fob and it has suddenly failed this is probably due to a faulty circuit board. You will need to replace the key fob with a new one from the dealer. It needs to be programmed for your car by the dealer.

Always have a spare key for this vehicle and keep the battery charged by using it occasionally.

Programming a new Key
Replacing a missing master key is quite expensive from Land Rover, try not to get sucked into the extra cost of "Dealer coding" You can do this yourself in 2 minutes by following the simple process below.
1) Get in and close all doors. Turn ignition on and off quickly and remove the key (all within about 5 seconds).

2) Within 30 seconds of turning the ignition off, while holding down the "unlock" button, press the "lock" button three times. Release the "unlock" button. (You may or may not get the confirmation from the door locks.) Holding the key at your head level provides best results as the key sensor is in the side window pillar.

3) Repeat for each key you want to initialize within 30 seconds after the last one you initialized (if you have more).

4) Right after doing the last key, quickly put the key back in the ignition and turn it on/off again to finalize.

The sensor is not in your key. It is in the Key Fob, unless your car is not equipped with keyless entry. If there is no key fob than your car is not equipped with vehicle immobilization.