Question about 1996 Honda Civic

1 Answer

Clutch noise In the morning when all engine components are completely cold, the clutch will squeak while pushing the pedal to the floor. The clutch also seems slightly jerky while the engine is warming up. I have no clue as to what it is.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

Sounds like it is the throwout bearing . They sometime will last a long time like that, but to replace it will have to remove trans

Posted on Jul 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 honda accord 5 speed.Drove it home parked .When I tried to go the next morning I could not shift to any gear If I turn off the engine I can shift ??


Any noises when you engage the clutch or shift? Could be several things. If it is hydraulic clutch, check the master cylinder level. It will be on the firewall just outside where pedals fasten to floor. Use dot 3 brake fluid to fill it if necessary. If it is full may have trouble with pressure plate and trowout bearing binding up.

Mar 08, 2013 | 2002 Honda Accord

1 Answer

2000 Camry clutch


Check the fluid in your slave cylinder. you have a master cylinder for the brakes and a slave cylinder for the clutch. It should have a screw on lid and if it's full, you probably need a new one.

Sep 27, 2017 | Cars & Trucks

2 Answers

There are few problems mentioned below: 1. In morning when engine is cold, it produces too much noise, when pressing clutch and it increases, when lifting the pedal (Half Clutch), when engine is hot, this...


from the description , the noise is a failing throw out bearing
the gear scratching is the fact that the clutch is not fully disengaging and there is still excessive torque in the input shaft for the syncro rings to work properly
fit a new clutch kit ( including new throwout bearing) before you have to rebuild the transmissionas well

Apr 01, 2017 | 2011 Mahindra Scorpio

1 Answer

1998 Ford Taurus SE, Problem Transmissions wont Shift, Took it to the Shop and they Said it Had to be a Electracal Problem?? But they did not Know what, Some times Works Fine Other Times Check Engine Comes...


TRY THIS I BET IT'S YOUR PROBLEM

Neutral Safety Switch
  • Put the selector in the park position.
  • Loosen the screws on the neutral safety switch.
  • Remove the switch.
  • Reverse the procedures to complete the installation.
Clutch Start Switch
CAUTION
Before replacing the clutch switch or any component connected to the vehicle's control computer, disconnect the negative cable from the battery.
  • After replacing the switch, slowly work the clutch pedal and note any unusual noises or interferences with pedal movement.
  • If the switch is adjustable, make sure the clutch pedal height and push rod (free) play are correct.
  • Then check the release point of the clutch.
  • Begin by engaging the parking brake and installing wheel chocks.
  • Start the engine and allow it to idle.
  • Without depressing the clutch pedal, slowly shift the shift lever into reverse until the gears contact.
  • Gradually depress the clutch pedal and measure the stroke distance from the point the gear noise stops (this is the release point) up to the full stroke end position.
  • If the distance is not within specifications, check the pedal height, push rod play, and pedal free play.
  • If the distance is correct, check the clearance between the switch and the pedal assembly when the clutch is fully depressed.
f_mt_tps9.26.jpg Clutch switch to pedal assembly clearance. Courtesy of Toyota Motor Company.
  • Loosen the switch and adjust its position to provide for the specified clearance.

May 22, 2010 | 1998 Ford Taurus

2 Answers

Clutch pedal went to the floor but did not come back up. Heard something 'pop' when pushing in clutch last night. Got home, then tried to start car this morning and clutch made a 'pop' sound again when...


there is a plastic clip that connects the clutch pedal to the rod that goes to the master cylinder, chances are that it let go. Bad thing is that it is only available from GM along with the rod. It is around 50

Oct 16, 2009 | 2003 Oldsmobile Alero

1 Answer

1994 S 10 Clutch problem


up under the dash where your peddle is mounted there is a bushing try a little spray lube to quiet the problem

Aug 23, 2009 | Chevrolet Blazer Cars & Trucks

1 Answer

No pressure clutch pedal goes straight to the floor 1988 holden r


If hydraulic actuated mechanism, loss of fluid, defective master cylinder or slave cylinder at the clutch. Missing pin or other part between slave cylinder and clutch arm. Loose or broken slave cylinder mounting. Missing pin or broken part between pedal and master cylinder. If mechanical linkage, look for broken components or missing pins at moving joints. If you tried to shift into gear with engine running, you may have damaged the transmission gears.

Aug 11, 2009 | 1993 Isuzu Rodeo

1 Answer

2003 toyota mr2 spyder 5 speed transmission grinding noise


Here is what is going on. When you push in the clutch pedal you remove the connection between the engine and the transmission. At this time all the parts in the transmission stop rotating.Since the only parts in the transmission that can rotate without moving the car are the input parts we can safely assume that the noise can only be from there.This can be a transmission input bearing. Worn Synchro mechanism (allows the transmission to shift without grinding the gears)Low fluid in the tranny. Or a bad clutch component. Top off or change the fluid. If it still makes the noise you need to take it to a tranny shop.

Nov 30, 2008 | 2002 Toyota MR2 Spyder

2 Answers

Clutch check


you have civic SI type R with the K20A engine and 6sp transmission? correct?

yes the clutch is adjustable.

  1. loosen the clutch pedal position switch(lower of the 2 switches) locknut and back off the clutch pedal position switch.
  2. loosen the clutch push-rod locknut and turn the push-rod in or out to get the desired height and stroke of the pedal.
  3. tighten the push-rod locknut
  4. with the clutch pedal released, turn the clutch pedal position switch in until it contacts the clutch pedal.
  5. turn the clutch pedal position switch in an additional 3/4 to 1 turn.
  6. tighten the clutch pedal position switch locknut.
  7. loosen the clutch interlock switch(the upper switch) locknut and then the interlock switch.
  8. press the clutch pedal to the floor.
  9. release the pedal about 1/2 in. from the fully depressed position, and hold it there. adjust the position of the interlock switch so that the engine will start with the clutch pedal in this position.
  10. tighten the interlock switch locknut.
clutch pedal stroke should be: 5.1 - 5.5 in
clutch pedal height should be: 7.76 in

if adjusting the clutch doesn't help with the transmission feeling notchy, may be the syncros.




Jul 09, 2008 | 2002 Honda Civic

Not finding what you are looking for?
1996 Honda Civic Logo

Related Topics:

123 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Marvin
Marvin

Level 3 Expert

81285 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...