Question about 1987 Peugeot Liberte

1 Answer

Carnt get the grub screws out of my rear break drums on my peugeot 406 tds estcan i drill them out

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Peugeot Master
  • 6,982 Answers

Never heard of a grub screw but if you mean the screws that attach the drum to the axle flange, try an impact driver (bit fits on end, you hit the rear with a hammer and it shocks and turns screw at the same time) If that does not work, yes...drill them out. the screws are'nt "special" and can be easily replaced (the wheel actually holds the drum on when installed)

Posted on Jul 12, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Hi I have a peugeot 406, I HAVE REPLACE THE FRONT BREAK DISC AND THE BREAK PADS BUT IT STILL GIVE THAT HORABLE NOIOSE WHEN I BREAK. Its realy iritating and i take good care of my car,

Remove the brake pads from the car and smear small amount of high melting point silicone grease e.g. Carlube, at the back of the brake pads. Be careful do not put on too much and never has it touch the pad material and the disc rotor. if you do, remove it with brake clearner immediately. The squeaks noise shall disappear if you fix it properly.

Sep 07, 2013 | 1999 Peugeot 406

1 Answer

Peugeot 406 where is the emmissions filter

try lookin under car in rear follow the hvac hose should be a black box around it some have hose in and out try that

Jul 11, 2012 | Peugeot 406 Cars & Trucks

1 Answer

What size bolts is neede to fit a towbar to a peugeot 406

there all the same unless u have pre drilled holes under the car,which means u can use the deals fiting kit

Jan 20, 2012 | 1999 Peugeot 406

1 Answer

I have a pug 406 2l hdi i have had a problem with the breaks

That sounds like a bad brake rotor or drum. If the brake rotor or drum is thick in one spot and normal on the rest that will cause the pedal to pulsate every time the the rotor or drum reaches that part of its rotation. The solution to this problem is to remove the front and rear rotors or drums and take them to a machine shop so they can be smoothed out, bear in mind you may need to replace them if the thick spot is too great.

Oct 22, 2009 | 2005 Peugeot 405

2 Answers

Peugeot 406 estate 2l hdi, anti polution light on

it would never be 1000 euros!!!!!!!!!!!! it will be part of the exhaust system it cuts out because its causing pollution

Sep 15, 2009 | 2005 Peugeot 405

1 Answer

Peugeot 406 2.0 HDI 99th,if i breake wit engine its go of

does it return to idle when at 900, this is programmed to shut off fuel injectors when car is pushing engine to save you fuel for when going down a hill, u push clutch and a signal tells it u have which returns back to idle.

Jul 04, 2009 | 1989 Peugeot 405

1 Answer

Hand break no good,??? big job ??? or D I Y ??? sorry on Peugeot 406 diesel estate

If fitted with rear discs, the handbrake shoes inside the disc will probably need adjusting as these tend to be ignored during service.

Mar 17, 2009 | 1987 Peugeot Liberte

2 Answers

Rear drum will not come off of 01 ford focus

There are no grub screws on focus drums,you have to undo the four bolts behind the drum to release it,it then comes off wheel bearing and all.

Mar 04, 2009 | 2001 Ford Focus

1 Answer

Peugeot 406 hdi 2000 [Wreg] front @rear fog

Send me your car chaisses number to get the wiring diagrem for helping

Mar 02, 2009 | 1991 Peugeot 405

1 Answer

Peugeot 406 SV rear seat removal

take it you have done it------- two brackets at front of seat

Oct 12, 2008 | 1991 Peugeot 405

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22413 Answers


Level 3 Expert

83850 Answers

xxxxxx xxx

Level 3 Expert

5013 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides