Question about 2000 Oldsmobile Intrigue

1 Answer

Washer pump won't stop - 2000 Oldsmobile Intrigue

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,596 Answers

Disconnect the motor and Connect A Test light to POS Terminal @ Motor Plug If Still Power there Wiper Switch is Bad, If NO POWER there The Washer Motor is STUCK so Replace it.
Hope this Helps

Posted on Jul 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Washer won't pump water to rear wiper


One reservoir, two separate pumps. First, listen if you can hear the pumps running. If they each are, something may be blocking the flow. Look in the reservoir and see if there is any debris blocking the intake at the bottom. Also check for kinks in the lines. Finally see if the nozzles are blocked. Good luck

Jan 25, 2013 | 1998 Plymouth Grand Voyager

1 Answer

2009 nissan frontier windshield washer pump won't work


Check fuse in fuse box inside vehicle,if good,then go to windshield washer pump and disconnect wiring,get meter and check if power is going to pump,if so then pump is at fault,if no power,thenwiring could be short somewhere to fuse box.Also check your washer hoses,that they are not kinked or came loose.Pump could just be loose.

Jan 04, 2013 | 2009 Nissan Frontier

1 Answer

1984 gmc vandura 3500 windshield washer -no power


it would be easier to remove the washer pump use two pieces of wire and jump it to the battery to make sure the pump even works. if you give it a direct power supply just for a moment to see if it even engages it won't hurt a thing. sure beats crawling all over the place trying to find the problem when it may be the washer motor itself

Jul 14, 2012 | Cars & Trucks

1 Answer

Window washer does not work


the pump is located on the bottom of the washer bottle that you filll with washer fluid.look at the bottom of the washer bottle there should be an electrical plug and a rubber/plastic hose this is the pump they are attached too.disconnect the electrical connector and the hose.if you have fluid in the bottle have it drain into a container or remove the bottle from the truck and turn the bottle so the fluid won`t run out it.then change the pump.and reassemble.

Jan 08, 2012 | 2006 Dodge Dakota

1 Answer

Why won't the windshield washer motor and fluid pump work on my 2005 Magnum SE? Turn signals work fine, but no washers. #18 fuse is good, too. Please help


could be the washer motor. have someone hit the switch while you listen at the pump to see if it is making noise. also check to see if you have voltage at pump. it could be stuck or corroded.

Jan 02, 2012 | 2005 Dodge Magnum

1 Answer

I have a 2000 Jeep Cherokee Sport that I beleive needs the washer fluid pump replaced and am seeking advice on where it is located and how to replace it.


the washer pump is located in the bottom of the washer bottle.if you remove the bottle disconnect the washer hose and electrical plug.most of the pumps you just pull it out of the rubber o ring that seals the pump so the fluid won`t run out and holds the pump in place.

Oct 25, 2011 | 2000 Jeep Cherokee

1 Answer

Winshield washer pump has stopped pumping on 1996


Sounds like pump alright Unbolt tank from car and pump should be screwed to bottom of tank Another way is fit a universal inline washer pump Up to you whether you want to keep your car original

Oct 22, 2009 | 1996 Audi A4

1 Answer

I have a 2001 626 4-clinder with a windshield washer pump that won,t work. I don,t know where to find it.


the pump is located inside the washer fluid reservoir.it is easy to service with the plastic inner fender removed.

Jul 29, 2009 | 1999 Mazda 626

Not finding what you are looking for?
2000 Oldsmobile Intrigue Logo

Related Topics:

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

Marvin
Marvin

Level 3 Expert

81424 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...