Question about 1991 Isuzu Trooper

1 Answer

How i get the Alternator bolt off that sits behind the belt tensioner on a 1991 2.8l v6 w/air

Posted by on

  • paul_scowcro Jul 12, 2009

    I typed too fast, its the Alternator Bracket that i cant get off

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 108 Answers

I have a 91 Rodeo, I use a 10mm wrench to get it off, unless its a 13mm bolt. I think the belt should run the same as mine, seems like the tensioner is upside down. I've never had problems getting my alternator out.

Posted on Jul 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I release the tension in the belt that drives the alternator in a 2007 Toyota Highlander V6?


most have a long bolt behind and you loosen of the centre nut so that the bolt behind can move the shaft
ON some v6 engines the tensioner is spring mounted and there is a 1/2 square drive in the front or the bracket
get a long handled 1/2 " strong bar, put the square in the hole and lift the pulley off the belt

May 29, 2015 | 2007 Toyota Highlander

1 Answer

How do you replace an alternator from 2002 Mazda 626 V6 engine?


FIRST TURN OFF RADIO.REMOVE NEGATIVE BATTERY CABLE.REMOVE FRESH AIR DUCT.REMOVE RADIATOR UPPER BRACKET.REMOVE CONDENSOR FAN IF EQUIPPED.REMOVE ELECTRICAL CONNECTORS FROM THE ALTERNATOR.LOOSEN THE BELT TENSIONER LOCK NUT AND TENSION ADJUSTING BOLT.REMOVE ALTERNATOR UPPER MOUNTING BOLT.REMOVE RIGHT SPLASH SHIELD. REMOVE DRIVE BELT FROM THE ALTERNATOR PULLEY.REMOVE AC COMPRESSOR AND SUPPORT IT ASIDE LEAVING THE REFRIGERANT LINES CONNECTED.REMOVE ALTERNATOR THROUGH BOLT.THEN REMOVE ALTERNATOR.

Mar 01, 2011 | 2003 Mazda Mazda6

1 Answer

I want to know how to remove the alternator kia optima 2003


  1. Disconnect the negative battery cable.
  2. Temporarily loosen the water pump pulley bolts, 1.6L (VIN 3) engine only.
  3. Remove the front air intake inlet pipe bolts, 1.8L engine only.
  4. Remove the top hose from the air intake inlet pipe, 1.8L engine only.
  5. Remove the air intake inlet pipe clamp and the pipe, 1.8L engine only.
  6. Remove the power steering pump, 2.0L engine only.
  7. Remove the power steering pump bracket, 2.0L engine only.
  8. Remove the alternator B terminal cover cap.
  9. Disconnect the alternator electrical connections.
  10. Loosen, but do not remove the alternator pivot bolt and the tensioner mounting bolt.
  11. Remove the drive belt(s); relieve tension on the belt by rotating the adjustment bolt.
  12. Remove the water pump pulley, 1.6L (VIN 3) engine only.
  13. Remove the power steering pump, 1.6L (VIN 3) engine only.
  14. Remove the power steering pump bracket, 1.6L (VIN 3) engine only.
  15. Remove the alternator tensioner mounting bolt and the belt tensioner.
  16. Remove the alternator pivot bolt.
  17. Loosen the bolt at the base of the adjusting bracket and rotate the bracket up.
  18. Remove the alternator.

    0996b43f80207fa4.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Alternator mounting-1.5L and 1.6L (VIN 5) engine shown


    0996b43f80207fa5.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Alternator mounting-2.0L and 1.6L (VIN 3) engines shown


    0996b43f80231908.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Alternator mounting-2.4L and 2.7L engine


To install:
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Install the alternator.
  3. Install the alternator pivot bolt and hand-tighten at this time.
  4. Rotate the adjusting bracket into position, place the belt tensioner into position. Hand-tighten the mounting bolt.
  5. Install the drive belt.
  6. Adjust the belt tension by rotating the adjustment bolt.
  7. The belt deflection for 1.5L, 1.6L (VIN 5), 2.4L and 2.7L engines, is as follows:
    1. New belt: 0.22-0.28 in. (5.5-7mm).
    2. Used belt: 0.24-0.28 in. (6-7mm).

  8. The belt deflection for 1.6L (VIN 3) engine is as follows :
    1. New belt: 0.13-0.15 in. (3.3-3.7mm).
    2. Used belt: 0.17-0.19 in. (4.2-4.7mm).

  9. The belt deflection for the 2.0L engine, is as follows:
    1. New belt: 0.22-0.31 in. (5.5-8mm).
    2. Used belt: 0.33-0.45 in. (8.5-11.5mm).

  10. The belt deflection for the 1.8L engine, is as follows:
    1. New belt: 0.23-0.31 in. (6-8mm).
    2. Used belt: 0.28-0.35 in. (7-9mm).

  11. Tighten the tensioner bolt to 14-19 ft. lbs. (19-26 Nm) and the pivot bolt to 28-38 ft. lbs. (38-51 Nm).
  12. Connect the alternator electrical connections.
  13. Install the alternator B terminal cover cap.
  14. Install the power steering pump and adjust the power steering belt tension, 2.0L and 1.6L (VIN 3) engines only.
  15. Install the water pump pulley, 2006 1.6L engine only.
  16. Install the air intake inlet pipe and fasten the clamp, 1.8L engine only.
  17. Install the top hose to the air intake inlet pipe, 1.8L engine only.
  18. Install the front air intake inlet pipe bolts, 1.8L engine only.
  19. Connect the negative battery cable.

Feb 09, 2011 | 2003 Kia Optima

2 Answers

I would like instructions to remove and replace the alternator in a 2004 FORD EXPLORER XLS with a 4.0L V6


Disconnect the battery

Remove the air snorkel and upper half of the air box. You may have to remove the engine cover to get at the clamp for the air snorkel at the throttle body.

You will see the serp belt tensioner on the drivers side of the engine. In the center of the pulley will be a bolt head. use the appropriate sized socket and ratchet to rotate the tensioner using the bolt head. Once the tension is off the belt it can be removed from the alternator pulley. You do not need to remove the entire belt.

Remove the three bolts holding the alternator to the bracket. A 15mm socket and possible a swivel should to the trick.

Remove the plug in connector from the alternator and remove the nut holding the battery cable to the backside of the alternator.

Make sure the new alternator is the same amperage, has the same mounting brackets and the same pulley size and the same number of groove. Essentially make sure it looks identical to the old one.

Then reinstall. It should take you about an hour tops. Good luck!

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Oct 14, 2010 | 2004 Ford Explorer

1 Answer

How do i replace the altenator


1. Remove the plastic air intake system which includes the air filter, 1 vacuum hose, the tube that runs to the carb, the tube that runs off to the left. There are three bolts that hold the bottom of the air filter housing on. Most of this system is a snap together assembly. Just pull it apart.

2. The alternator will have two bolts on the front bottom. The left one is a double sided bolt and the right one is a pass through bolt with a nut on the back. Stick a wrench or a short socket wrench on the nut behind the alternator and remove the pass through bolt from the front. Then remove the double sided bolt from the left side.

3. This leaves the alternator loose and being held by the belt. remove the belt from the alternator and wiggle and jiggle the alternator out of the mounting area (very tight squeeze to get it out). You can put a larger size can of fruit or something in the place of the alternator to hold the belt in place so you can remember how it looks.

4. You will need to loosen the belt tensioner to put the belt on the new alternator. Remove the can of fruit if you chose to do that but be careful to not accidentally remove the belt from the 5 or 6 different places it passes through. Place the new alternator, put in the bolts and tighten. Loosen the tensioner and put the belt on. Tighten the tensioner and adjust as needed. Replace the entire air intake system by snapping it all back together and bolting it in one piece at a time.

Aug 26, 2010 | 1994 GMC Safari

1 Answer

What are the steps to replace a 1999 Mazda 626 V6 alternator? Thanks


Remove cables from alternator. Loosen tensioner bolt. Remove belt. Replace alternator. Replace belt. Tighten tensioner bolt. Replace cables and done. Mike. Rate 100% please.

Sep 22, 2009 | 1999 Mazda 626

1 Answer

How to check alternator, and how to replace it.



Removal & Installation

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Disconnect the negative battery cable.
  3. Temporarily loosen the water pump pulley bolts, 1.6L (VIN 3) engine only.
  4. Remove the front air intake inlet pipe bolts, 1.8L engine only.
  5. Remove the top hose from the air intake inlet pipe, 1.8L engine only.
  6. Remove the air intake inlet pipe clamp and the pipe, 1.8L engine only.
  7. Remove the power steering pump, 2.0L engine only.
  8. Remove the power steering pump bracket, 2.0L engine only.
  9. Remove the alternator B terminal cover cap.
  10. Disconnect the alternator electrical connections.
  11. Loosen, but do not remove the alternator pivot bolt and the tensioner mounting bolt.
  12. Remove the drive belt(s); relieve tension on the belt by rotating the adjustment bolt.
  13. Remove the water pump pulley, 1.6L (VIN 3) engine only.
  14. Remove the power steering pump, 1.6L (VIN 3) engine only.
  15. Remove the power steering pump bracket, 1.6L (VIN 3) engine only.
  16. Remove the alternator tensioner mounting bolt and the belt tensioner.
  17. Remove the alternator pivot bolt.
  18. Loosen the bolt at the base of the adjusting bracket and rotate the bracket up.
  19. Remove the alternator.

    0900c15280028419.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Alternator mounting-1.5L and 1.6L (VIN 5) engine shown


    0900c1528002841a.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Alternator mounting-2.0L and 1.6L (VIN 3) engines shown


    0900c1528002841b.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Alternator mounting-2.4L and 2.7L engine

To install:
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Install the alternator.
  3. Install the alternator pivot bolt and hand-tighten at this time.
  4. Rotate the adjusting bracket into position, place the belt tensioner into position. Hand-tighten the mounting bolt.
  5. Install the drive belt.
  6. Adjust the belt tension by rotating the adjustment bolt.
  7. The belt deflection for 1.5L, 1.6L (VIN 5), 2.4L and 2.7L engines, is as follows:
    1. New belt: 0.22-0.28 in. (5.5-7mm).
    2. Used belt: 0.24-0.28 in. (6-7mm).

  8. The belt deflection for 1.6L (VIN 3) engine is as follows :
    1. New belt: 0.13-0.15 in. (3.3-3.7mm).
    2. Used belt: 0.17-0.19 in. (4.2-4.7mm).

  9. The belt deflection for the 2.0L engine, is as follows:
    1. New belt: 0.22-0.31 in. (5.5-8mm).
    2. Used belt: 0.33-0.45 in. (8.5-11.5mm).

  10. The belt deflection for the 1.8L engine, is as follows:
    1. New belt: 0.23-0.31 in. (6-8mm).
    2. Used belt: 0.28-0.35 in. (7-9mm).

  11. Tighten the tensioner bolt to 14-19 ft. lbs. (19-26 Nm) and the pivot bolt to 28-38 ft. lbs. (38-51 Nm).
  12. Connect the alternator electrical connections.
  13. Install the alternator B terminal cover cap.
  14. Install the power steering pump and adjust the power steering belt tension, 2.0L and 1.6L (VIN 3) engines only.
  15. Install the water pump pulley, 2006 1.6L engine only.
  16. Install the air intake inlet pipe and fasten the clamp, 1.8L engine only.
  17. Install the top hose to the air intake inlet pipe, 1.8L engine only.
  18. Install the front air intake inlet pipe bolts, 1.8L engine only.
  19. Connect the negative battery cable.

Jul 29, 2009 | 2002 Kia Spectra

1 Answer

HOW HARD IS IT TO REMOVE AN ALTERNATOR


Yes, very easy...here is the steps to do it:

To Remove:
  1. Disconnect battery negative cable.
  2. Remove air cleaner inlet pipe.
  3. Disconnect alternator electrical connections.
  4. Loosen (but do not remove) pivot bolt and tensioner mounting bolt.
  5. Remove drive belt form alternator pulley.
  6. Remove tensioner mounting bolt and belt tensioner.
  7. Remove pivot bolt, loosen adjusting bracket bolt and rotate bracket up.
  8. Remove alternator.

To Install:

  1. Place alternator on engine.
  2. Install (but do not tighten) pivot bolt.
  3. Rotate bracket down on top of alternator.
  4. Install belt tensioner and install bolt loosely.
  5. Install drive belt on alternator pulley.
  6. Tighten tensioner bolt to 14-19 ft lb (19-26 Nm).
  7. Tighten pivot bolt and bracket bolt to 28-38 ft lb (38-51 Nm).
  8. Connect alternator electrical connections.
  9. Install air cleaner inlet pipe.
  10. Connect battery negative cable.

120f25e.gif

Jul 13, 2009 | 1999 Kia Sportage

1 Answer

Changing the alternator on 1999 miata


The alternator is held on by two bolts. The top bolt is part of the tensioner, which uses, thankfully, an old style bolt system to tension a separate alternator belt. Once you remove the top bolt the tensioner can be removed by sliding it towards the rear of the car through the slot it sits in. The bottom bolt has fallen prey to what I consider an engineering oversite. The bolt threads out towards the back of the engine, and because of this, you have to remove the stiffening arm that sits right behind this bolt. Fortunately, the stiffening arm is held on by three bolts, all of which are easy to get to. Once this arm is out of the way you can remove the bottom bolt.

Apr 17, 2009 | 1999 Mazda MX-5 Miata

1 Answer

How to remove and install alternator on 2001 kia sephia


    1. Remove or disconnect the following:
    2. Negative battery cable
    • Front air intake inlet pipe bolts
    • Top hose from the air intake inlet pipe
    • Air intake inlet pipe clamp and the pipe
    • Alternator B terminal cover cap
    • Alternator B terminal nut and the B terminal lead
    • Alternator L and S electrical connections
    • Alternator pivot bolt and the tensioner mounting bolt, loosen but do not remove
    • Drive belt(s); relieve tension on the belt by rotating the adjustment bolt
    • Alternator tensioner mounting bolt and the belt tensioner
    • Alternator pivot bolt
    1. Loosen the bolt at the base of the adjusting bracket and rotate the bracket up.
    2. Remove or disconnect the following:
      • Alternator

    Apr 02, 2009 | 2004 Suzuki Aerio

    Not finding what you are looking for?
    1991 Isuzu Trooper Logo

    Related Topics:

    86 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Isuzu Experts

    Marvin
    Marvin

    Level 3 Expert

    81423 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22359 Answers

    Thomas Perkins
    Thomas Perkins

    Level 3 Expert

    14423 Answers

    Are you an Isuzu Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...