Coil light doesn't come on it takes up to ten turns of the key before it comes on

be more specific.... if theres no dash lights when u turn key in on then its the main fuse under hood. if it turns over and wants to start could be ur ecm/ ignition module , ( if theres coils pretty sure its feul injected ur ecm,/or ignition module would be ur coil packs). when u turn the key in on u hear any kind of noise under trunk might take two people for that if not ur feul pump

look for security light when you turn on key if it lights and doesn't go off leave key on for ten minutes then turn key off and then try to start

turn the igntion on, don't start, let it set for ten minutes Turn it off for 5 seconds then try to start it. If it lost memory for some reason and doesn't start . then do this three times , after the third time start it. that is the relearn procedure. Have a charger on it for the 30 minute relearn. Relearn is on for ten m off five s on ten off five on ten off five then start

you can get a new key from a dealer and program it yourself by leaving the key on for ten minutes and the security light turns of then you turn the key to off for ten seconds and turn it back on and the security light will come back on for ten more minutes you do the turn it on and wait process 3 times and the light will go out the 3rd time and you can turn the key off for 30 seconds and it should start after that. some times they will work after the first ten minutes.

CHARGE BATTERY / TURN KEY TO RUN POSITION FOR TEN MINUTES
SECURITY LIGHT SHOULD GO OUT / TURN KEY OFF FOR 3-5 SECONDS
TURN BACK TO RUN FOR TEN MINUTES / REPETE / USALLY TAKES
3 TEN MINUTE CYCLES / THAN TURN OFF / TURN ON SECURITY LIGHT
SHOULD GO OUT AND ENGINE START AND RUN

did your old cylinder have wires coming out of it ? did your old key have a chip in it is your security light on? if so the vechicle will not start

the process takes about thirty minutes. in three ten minute key cycles. here is how you do it . make sure that the battery is fully charged. step on parking brake pedal and leave it down this will keep the head lights off. turn the key and try to start it then leave it in the on position. you have to leave the key in the on position for ten minutes. you will see the security light on. after the ten minutes the light will go off then turn the key to the start position. turn the key all the way back to the off position and count to three. then try to start it and leave the key in the on position for another ten minutes till the security light goes out. you have to do this same process three times to reset the security system. sometimes you get lucky and it will start after the first ten minute cycle.

TRY THE RELEARN PROCEDURE.....INSERT KEY IN IGNITION, AND TURN TO THE RUN POSITION,,DO NOT CRANK THE ENGINE..LET CAR SET WITH KEY ON FOR TEN MINUTES.. THEN TURN KEY OFF AND THEN BACK ON FOR ANOTHER TEN MINUTES... AGAIN TURN OFF THEN BACK ON FOR THE LAST TEN MINUTES... AFTER TIME IS UP TURN OFF REMOVE KEY AND REINSERT AND ATTEMPT TO START CAR.. IF STILL NO GOOD TRY A SPARE KEY IF YOU HAVE ONE IF STILL NO GOOD TAKE YOUR KEY TO DEALER FOR REPRORAMMING

Turn the key on and wait for the security light to stop blinking (may take about ten minutes). Then turn the key off and wait for at least one minute. Then try to start. That should program the key chip.

1. Turn the key to “Run,” but don’t start
2. Press “ENG MET” on the Trip
the engine.
Monitor. Then, within five seconds,
press it again.
3. Within five seconds, press and hold
“GAUGES” on the Trip Monitor. The
“CHANGE OIL” light should flash.
4. Hold the “GAUGES” button until the
“CHANGE OIL” light stops flashing
and goes out. This should take about
ten seconds.
When the light goes out, the monitoirs
reset. If the monitor doesn’tr eset, turn the
ignition off, then try again.