Question about 1996 Audi A4

1 Answer

Waay onrning lights

I changed the c.v.joints and now the abs and emergency lights st

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,129 Answers

You may have an issue with the pick up abs signal sensor located on the outer end of the cvu joint shaft right where it goes into the spindle carrier it may not be located close enough or it may have been bumped out of alignment during install or it may be to close to its pick up, inspect it I think it should be about .025" feeler gauge air gap between sensor pick up and magnetic delivery ring.

Posted on Jul 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What would cause the Emergency Brake light to not go off when the emergency light is released? What causes the ABS warning light to come on?


When I had that problem with the emergency light it was the sensor for emergency brake
The abs and brakes sounds like you are loosing pressure in the system

Apr 18, 2015 | 2004 Toyota Prius

1 Answer

Where is the fuse for the 2002 highlander ABS


The fuse for the ABS in a 2002 Highlander is in the black plastic covered box under the hood. If you take the fuse out, the ABS warning light and the emergency brake warning light will illuminate on your dashboard. The brakes will work as if you never had ABS, and the car will chime when you first start off if the emergency brakes are on.

Aug 23, 2012 | 2002 Toyota Highlander

1 Answer

2001 kia optima lurches and emergency brake light and abs light go on


you must go to the repair shop for test with the computer and Scanner.

God bless you

Jun 22, 2012 | Cars & Trucks

1 Answer

Anti-lock ABS light came one after ball joint replacement.. Codes?


Did the spindle hang down and rip the wires into. Need to hook up a scanner to see which abs sensor it is.

Jun 16, 2012 | 1996 Chevrolet Blazer

2 Answers

Abs light on in my ford ranger 1999


ABS light tells you that there is some problem with the brake system like you have forgot to release the emergency brake or its time for you to change the brake fluid. Ford recommends to change the brake fluid every year.If you have recently refilled the brake fluid , check for any leaks.Abs light indicates that your braking system needs to be serviced.

Feb 15, 2011 | Ford Ranger Cars & Trucks

2 Answers

I,m tired to figure out the lihts ABS and Brake on some times and the abs system dont respond and emergencies cases,I replace the shocks front and rear, also i change the master cilynder and the brake...


check out the abs sensor, it is located on the rear axle of the truck, bolted to the 'pumpkin'-they commonly fail and exhibit all the symptoms you are describing.

Jan 26, 2011 | 1999 Dodge Durango

2 Answers

My brake lights won't go off and I'm getting a message on the dashboard that has trackoff and a yellow antilock light


Your car may be low on Brake fluid. Pop the hood and check the brake fluid reservoir. There is usually a line that shows how much fluid should be in the reservoir. It should be pretty full, so add fluid if needed. Perhaps you have some sort of brake fluid leak?

I would take a calculated guess that it is strictly a saftey factor (in an emergancy on the highway if your foot is on the brake you are less likely to be rear ended) and if this is indead true, than it is wired to the battery independant of your starter switch

If the brake lights are staying on even with your foot off the brake, it may be that the switch controlling the brake lights is broken. Beware; this can drain the battery, think in wire shortage.

Keep us updated.

Jan 13, 2011 | 2000 Buick Century

1 Answer

How to install abs ring?


ABS ring at front fits on CV joint and should come fitted on a new joint. if not fitted, can be tapped on lightly and evenly using a hammer and punch. rear ABS ring fits inside brake drum. when changing discs/drums ring must be tapped off with punch placed through wheel bolt holes to back of ring. to refit tap on to inside of drum.

May 23, 2010 | 1997 Audi A4

1 Answer

EBCM


No, absolutely not, although the EBCM might possibly be the problem, it is a costly item and 95% of the time is replaced for nothing. Make sure to get the system diagnosed properly, if he can't get a reading from the diagnostic machine, check the abs (EBS) fuse(s), it (they) might be burnt. Then check for fluid level and fluid leaks in the brake system. If these are OK, get the wiring checked to the EBCM for powers, grounds, and data (diagnostics).

Aug 27, 2008 | 2002 GMC Yukon XL

Not finding what you are looking for?
1996 Audi A4 Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

Marvin
Marvin

Level 3 Expert

81400 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14423 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...