Question about 1989 Mazda 626

1 Answer

High beams stick on when i use the turn signal

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Turn signal/high beam switch is bad

Posted on Jul 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 chev sub head lights wont turn on


Do you know anything about automotive electronics ? Electronic control modules .
Headlamp ON/OFF control is determined by the body control module (BCM) by a signal on the headlamp switch on input circuit when the headlamp switch is in the HEAD position. When the headlamp switch is in the AUTO position, the BCM determines headlamps ON/OFF by the voltage from the ambient light sensor.
If the headlight switch is left in the ON position, the inadvertent power control feature will turn OFF the headlights approximately 10 minutes after the ignition switch is turned to the OFF position. If the driver places the headlight switch in the ON position after the ignition switch has been turned OFF, or if the ignition switch is in the ACCY position, the headlights will remain ON until turned OFF or the battery runs dead.
The high beam indicator is illuminated when the instrument cluster receives a GMLAN serial data message from the BCM that the high beams are illuminated.
High Beams
The high beam headlamps receive voltage from the headlamp high relay located in the underhood fuse block. The BCM controls the relay on the headlamp high beam relay control circuit. High beam control is determined by a signal on the headlamp dimmer switch signal circuit from the multifunction switch. When the headlamp dimmer switch signal circuit is grounded, the BCM grounds the headlamp high beam relay control circuit, illuminating the high beam headlamps. The right and left high beam circuits are independent and are fused independently in the underhood fuse block.
Low Beams - Standard
The low beam headlamps receive voltage from the headlamp low beam relay located in the underhood fuse block. The BCM controls the relay on the headlamp low beam relay control circuit. Low beam control is determined by a signal on the headlamp dimmer switch signal circuit from the multifunction switch. When the headlamp dimmer switch signal circuit is open, the BCM grounds the headlamp low beam relay control circuit, illuminating the low beam headlamps. The right and left low beam circuits are independent are fused independently in the underhood fuse block.

Hooking up a factory scan tool an checking DTC'S - diagnostic trouble codes would be the very first step in trouble shooting this problem .
DTC B257A 00: Headlamp Switch Input Signal Mismatch
DTC 2575 00: Headlamp Control Circuit

Jun 30, 2017 | Cars & Trucks

1 Answer

How do I get the headlight to stay on high bean


try pushing the turn signal stick forward. if that does not work, you may need a new switch.

Nov 23, 2014 | 1988 Lincoln Town Car

1 Answer

Do not have lowbeam headlights on a 2005 Hyundai XG350


yes,the low beam lights turn on when night time comes around,the high beams come on after you push the stick that controls the lights in or out away from you. not the turn signal stick but the other stick on the opposite side

Dec 28, 2009 | Hyundai Motor 2005 XG350

1 Answer

How to replace the light switch (high beam/turn signal) lever in a 2004 Ford Focus. The lever won't go in to place to make your high beams work. Can you give me step by step instructions on how to replace....


Before you order the part try this.

The problem can cause by dust,dirt and the protective grease drip onto the electrical contacts.

It happen on my Ford long time ago and I fix it with spending a penny..

=====

Pass a vacuum over the general area of the light switch.

That's the easy part.

Test the turn signal and high beam.

If it's a no go then take the key on and MOVE THE STICK back and forth 30+ time left and right

IT may be repaid movement.

Move the stick HI LO 30+ times.


This FAST movement will get the dirt and shipping grease out and re-new the contacts.


Test it and see what happen.

========







Dec 10, 2009 | 2004 Ford Focus

1 Answer

No high beams, problem is not multifunction switch


Check the headlight switch to make sure that the connections or internal connections aren't corroded. This was a major problem for older fords, so it would be good to check it anyway.

Mar 26, 2009 | 1999 Dodge Caravan

1 Answer

No high beams on 1999 Dodge Caravan; low beams work fine


replace the switch in the column i had the same problem on a 1996 caravan when i replaced the switch the problem stopped

Jan 02, 2009 | 1999 Dodge Caravan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...