Question about 1988 Jeep Cherokee

1 Answer

Air won't bleed out of master cylinder.Is there a special trick?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

If you are referring to bleeding the brake syatem of air, you have to start with the farthest wheel form the master cyl. That would be the right rear, then do the left rear, then the right front and finally the left front.

Posted on Aug 03, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the correct brake bleeding order for 05 Buick rendezvous?


You need a special tool to bleed the ABS hydraulic control module first, if you have that then you start by bleeding the wheel farthest from the master cylinder, that is the left rear, then the right rear and then the right front and then the left front. The master cylinder must be bench bled before installing and all air purged...

Mar 24, 2017 | Buick Rendezvous Cars & Trucks

1 Answer

2004 ford focus 2.0liter. clutch pedaL GOES TO FLOOR. brake master full of fluid.I clutch master or clutch slave cylinder bad?


a plastic master cyl !

master cyl is bypassing internally

slave cylinder is inside the gearbox bell housing
if its leaking .....gearbox out




26351104-h2ljceqgvzc5xcxajl4olrsz-4-0.jpg

26351104-h2ljceqgvzc5xcxajl4olrsz-4-1.jpeg

26351104-h2ljceqgvzc5xcxajl4olrsz-4-3.jpg

Nov 11, 2016 | 2004 Ford Focus

1 Answer

How to bleed clutch master cylinder of toyota hi ace commuter 2010 model??


you bleed the same as you would bleeding brakes. you just won`t get the hard pedal like with brakes but you should feel resistance and no air coming out of system when you open the bleeder screw on the slave cylinder. make sure the reservoir does not get empty or you won`t get the air out of system.

Aug 04, 2015 | 2007 Toyota Hi-Ace 220

1 Answer

I have a 1988 f350 diesel i replaced the clutch master cylinder and the slave cylinder bled the lines and the truck still wont go in gear the throw out arm is moving about 1/2 inch what could be my prob


Ford has special bleeding and blocking instructions for clutch slave. Check manual for proper bleeding requirements. May consider presurre bleeding of master cylinder or use master cyclinder bleeding tubes that fill the resevoir as you bleed the and remove all air in system.

Jan 21, 2013 | Cars & Trucks

1 Answer

Kia Sephia 5 spd won't shift gears


You need to bleed the lines with a special tool, contact the dealer on this.

Jun 13, 2012 | 2000 Kia Sephia

2 Answers

My brake pedal goes all the way to the floor there is no any brake oil leak i replace the brake master cylinder i bleed the system but still the same what is the correct procedure to bleed brake system...


fill master cylinder, start at right rear. the way I do it is make sure cap is back on master cylinder. pump the brakes a few times then hold them. have another person open the bleeder valve at the tires until brakes go to floor. hold them down until bleeder is retightened but be sure master cylinder is not out of fluid. then go to left rear and do the same procedure, then right front, then left front. check fluid and if air is all out there should be brakes. good-day ! THIS IS HOW I HAVE ALWAYS DONE IT ! heres a little trick of sorts. you can change a master cylinder, and if you bench bleed it first. and no fluid is lost from the master cylinder lines you do not need to bleed the whole system. but make sure cylinder is full of fluid before putting on vehicle and all air is out of master cylinder.

Oct 23, 2011 | 1997 Ford Expedition

1 Answer

I am having a problem with bleeding the brakes. The truck has a proportion vavle for the rearend, maybe the first type of ABS? I'm not to sure. I can bleed the brakes starting with the rear-end and working...


mcdevito75 here, You have a dual chamber master cylinder sounds like 1 of those cahmbers the rear one is faulty, the master cylinder is most likeky the main prblem, specially if this was happening slowly. Try to re-bleed in this sequense left front, right front, left rear, right rear make sure the stream of fluid is solid, no spurting at the bleeder, and keep the master cylinder full when bleeding, if you let the master cylinder go to low while bleeding your only sucking in more air.

Jun 17, 2010 | 1991 Toyota Pickup

1 Answer

Needs to bleed the hydrolic clutch


want to know a short cut? (trick) take the master cylinder for the clutch off the firewall and tilt forward while pumping the pistron by hand and bleeding those fords are notorious for air locking in the master cylinder due to the fact!! they fasten to the firewall at a backwards tilt!! i have done over 2700 of them in 45 years

Jan 13, 2010 | 1991 Ford F250

3 Answers

I replaced the mst cyl. how do I bleed the ABS sys to get the air out? 97 ford F-150


You bleed it like you would a normal system but you must use the boost assist to do it, in order to do this start the truck pump the brakes three times and bleed that cylinder farthest away from the master cylinder do this twice or until you get clear fluid to run out. add fluid for every cylinder before moving on. Do this for each wheel and after doing all four wheels you should be ready to go. If it feels mushy you will have to bleed it a second time. But you must have the engine running to bleed the brakes unless you have a power bleeder. You may want to bleed the master cylinder first to do this add fluid to the cylinder then pump brakes three times crack the front line open and allow it to bleed air rout of the line do the same for the rear master cylinder once yo get solid fluid from the master cylinder you can dot the same for the ABS then do the wheel cylinders and wheel calipers. This needs to be done sometimes, be sure to never let the master cylinder run out of fluid and check it each time you bleed the wheel cylinders.

Nov 16, 2009 | 1997 Ford F150 Regular Cab

1 Answer

Im having difficulty in bleeding a cluch o a ford


clutch systems bleed just like brakes, if you have an external leak at the clutch master cylinder, then bleeding will be difficult, it should be replaced. I use a two person bleeding system, I fill the master, crack the bleeder screw open and have my 2nd push the clutch down and hold it, then I close the bleeder and tell my 2nd to release the pedal, repeat until no air is present.

Apr 08, 2009 | Ford Club Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

216 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...