Question about 1996 Toyota RAV4

1 Answer

I just repaice front end wheel bearings, when I

I just replkaiced front end wheel bearings, when I took the car in the front end seemed fine. After picking the vehicle up, every time I run or a bump or tar line I'm getting a lound clunk in the right front. I've repalced shocks twice,and have 174K miles.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 115 Answers

Try replacong the sway bar bushings

Posted on Jul 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Roaring noise with my 2006 Chevy Cobalt?


while the wheel bearings still feel tight they are the cause of your problem, after a collision most cars suffer from this problem depending on the speed of the accident the forces encountered during a sudden stop causes intense stress and fatigue on the bearings

Dec 06, 2012 | 2006 Chevrolet Cobalt

1 Answer

When driving down highway my front end has shimmy i have new tires new rims ,struts,tie rod outter ends,new sway bar bushings and my wheel bearings seem fine what is causing the shake


did you get it aligned !! if not, that may be why. good-day !! if you let go of steering wheel while going straight and it vears either way it means its out of alignment.

Jul 26, 2011 | 2002 Chevrolet Monte Carlo

1 Answer

ABS enguaging on its own. Replaced both front wheel bearings. What would cause this? Had a recent MVI done and the Mechanic said the front Right wheel bearing need to replaced. He put a new on on and...


Not supposed to use air gun on axle nut

Torque Wrench -- as you did

Check Wheel Sensors -- one may be bad or more
likely the mechanic damaged it.

Use a Volt Meter --put on A/C unplug sensor &
put meter on wires and spin the wheels

Do all four & compare

Jul 24, 2011 | 2003 Cadillac Sts

1 Answer

On my 1998 infiniti I30t the front end makes a whirring noise, when in motion,with any position of the steering wheel left of center. It does it in drive and in neutrul. i took of the drive shafts and they...


sounds like the power steering try this jack up the front end with engine off turn ignition key to the on position but not running turn the wheel back and forth to both stops a couple times start engine and see if whirring sound is gone

May 28, 2011 | Infiniti I35 Cars & Trucks

1 Answer

Rumble in front end


possible constant velocity joints dry or worn to excess try turning hard lock and drive round if noisy then a would say that's your problem

Apr 09, 2010 | 2004 Nissan Sentra

3 Answers

I have and 2003 Mustan Cobra. I was hearing a


You could have a failed wheel bearing. Jack the rear up with the trans in neutral (chock the front wheels please) and try to spin the tire. it should spin fairly easy. If you feel grinding or the wheel is difficult to spin then I would say it is the wheel bearing.

Feb 17, 2010 | 2003 Ford Mustang

2 Answers

Is a ball bearing the same as a wheel bearing hub assy , I took my 2001 Dodge Dakota to a repair shop he replaced the front wheel bearing hub assy, when I took my truck home it started making a popping...


????? This vehicle should be equiped with tapered roller bearings. Ball bearinga are out dated and not used since the 60's. No on the hub assembly, The brgs go into the hub and are replaceable as a seperate part.. $ 500.00? This is a mechanic? Do this, jack up the front end of the vehicle and rotate the wheel to determine if there is a proble. Not ant rough or hanging up of ythe wheel while turning it. Then put one hannd on the top and one on the bottom and push and pull. You are now checking for loose bbearings. Any looseness or roughness is a call to have the wheel and hubs pulled and inspected. 500.00? He is trying to get rid of you by quoting an outrages price. If you accept the estimate he is all the more happier for ripping you off. Take it to another shop and say no more than " Please chk the front end and wheel brgs. DSay no more than that and leaave them to their work. They will call you when they need you. Ask for the old parts if you have them replace or repair.. My estimate. 20 to 30.00 in parts and shop time 1.5 hrs. A reputable shop will show you where,why,and how.the process works..

Oct 28, 2009 | 2001 Dodge Dakota

3 Answers

Inner tread wear always on driver side front tire only. alignment is always fine


Same problem , yes slight tilt to top. Replaced strut. Still looks tilted..

Aug 15, 2009 | Ford Escape Cars & Trucks

2 Answers

I Think I have a front wheel bearing problem


yes it has and you need to change it before the wheel flips on you

Jan 20, 2009 | 2003 Kia Sedona

Not finding what you are looking for?
1996 Toyota RAV4 Logo

Related Topics:

149 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...