Question about 1998 Dodge Stratus

1 Answer

Drivebelts where is the tension pulley adjuster for drivebelt connection p/s to c/s on a 1998 dodge stratus 2.5l v6. if you could enclose a diagram i would appreciate. thanks in advance.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 1,757 Answers

Click on the following free direct Link. It has the correct Serpentine/Drive Belt Diagrams for your 1998 Dodge Stratus with you 2.5L V6 Engine and the Engine Options (AC/No AC etc.).

http://www.2carpros.com/car_repair_information/year/1998/make/dodge/model/stratus/1998_dodge_stratus_drive_belt_routing_diagram.htm

Let me know if this helped, or if you have additional information questions. Feel Free to contact me at FixYa.com!

Posted on Apr 02, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Belt came off 97 achieva how is it put back on


to replace drive belt rotate tensioner pulley clockwise then slip on new belt look under hood on the radiator shroud for drivebelt routing diagram.check drive belt tensioner for damage or looseness because very seldom drive break either cracked worn or drivebelt tensioner faulty.

Aug 06, 2013 | 1994 Oldsmobile Achieva Special Edition

1 Answer

Belt routing diagram for 2002 ford escort zx2


The drivebelt diagram for a 2002 ecort zx2 is enclosed. please note that the escort came with two engines i have enclosed both belt diagrams, you can use the diagrams to find yours by looking at the pulley locations or using the engine vin # located on the diagram, to find yours you will need to count the vin # of your car, this is located on your insurance card or on the drivers door next to latch or bottom of windsheild on the driverside, you will count from left to right to 8th digit and thats the eng code digit. good day.11_24_2011_3_54_42_pm.gif11_24_2011_3_55_06_pm.gif

Nov 24, 2011 | Cars & Trucks

1 Answer

How to install drivebelt on ford windstar 1998 3.8 l


1. Place a wrenchon the tensiorer pulley bolt and rotate the tensioner body until tenion on the belt is relieved.
2. Remove the belt from the auxiliary components and carefully release the tensioner.
3. Route the new belt over the various pulleys, again rotating the tensioner to allow the belt to be installed, then release the belt tensioner. Make sure the belt fits properly into the pulley grooves - it must be completely engaged.
Good Luck

Jul 17, 2010 | 1998 Ford Windstar

1 Answer

Replace water pump v6


1. Drain the coolant.
2. Loosen, (don't remove yet) the 4 bolts that hold the water pump pulley.
3. Remove the drivebelt. In order to remove the belt you need to put a wrench on the tensioner pulley to decrease the tension on the belt.
4. Now remove the 4 bolts loosened in step 2.
5. Disconnect the upper radiator hose from the water pump and disconnect the bypass hose from the top of the water pump.
6. Remove the drivebelt tensioner by removing the bolt in the center of it.
7. Remove the water pump bolts. There are 6mm and 8mm bolts, a total of 12 bolts. They are not all the same length. Be careful to note which bolts go in which holes.
8. After all bolts are removed sometimes the pump will require a little whack with a rubber mallet to unseat the gasket. Never pry between the pump and engine block.
9. Before installing the new pump, clean all the old gasket material from the engine block.
10. Use RTV sealant on both sides of the gasket for the new pump.
And............ the rest is just reversing the above except that you can fully tighten the pump pulley before putting the belt back on.
I hope this is helpful.

Mar 26, 2010 | 1995 Mercury Villager

1 Answer

Which pulley is the tension pulley on a 1998 mercedes E320


YOU SHOULD HAVE A DRIVEBELT ROUTING DECAL ON THE UPPER RADIATOR PANEL.SOME MODELS HAS A CAST IN HEX ON THE TENSIONER ARM.YOU CAN USE A WRENCH OR SOCKET.SOME MODELS PLACE A TORX BIT ONTO THE FASTENER IN THE CENTER OF THE PULLEY.

Mar 01, 2010 | Mercedes-Benz E320 Cars & Trucks

1 Answer

Replacing tension wheel on drivebelt


Click on the following free direct Link. It has the correct Serpentine/Drive Belt Diagrams for your 1998 Ford Windstar with either the 3.0L or 3.8L V6 Engine.
These have the Diagrams of the variety of Tensioners that are used. NOTE: Most of the Tensioners have three (3) bolts that mounts the Tensioner Assembly to the Engine. After removing the Belt: Remove the three (3) Bolts and remove the Tensioner.
http://www.2carpros.com/car_repair_information/year/1998/make/ford/model/windstar/1998_ford_windstar_drive_belt_routing_diagram.htm

Let me know if this helped, or if you have additional information questions. Feel Free to contact me at FixYa.com!

Dec 17, 2009 | 1998 Ford Windstar

1 Answer

How to remove water pump drivebelt on 2005 Escape


If there is no tensioner pulley then you will have to pry it on and off or remove water pump.

Free manual if you go to autozone..com and register.
or go to google ebooks and find a free chiltons manual.

Oct 06, 2009 | 2005 Ford Escape

1 Answer

How do you remove and replace the AC/PS drivebelt


Click on the following free direct Link. It has the correct Serpentine/Drive Belt Diagrams for your 2004 Dodge Neon 2.0L SOHC Engine with AC and PS. Included are Instructional and Directional Diagrams on "how" to remove the AC/PS Belt along with other very useful Diagrams for your use.

http://www.2carpros.com/car_repair_information/year/2004/make/dodge/model/neon/2004_dodge_neon_drive_belt_routing_diagram.htm

Let me know if this helped, or if you have additional information questions. Feel Free to contact me at FixYa.com!

Jun 06, 2009 | 2004 Dodge Neon

1 Answer

Fan belt


slacken the alternator pivot mounting bolt and the adjusting arm bolt then move the alternator towards the engine . slip the drivebelt off the alternator pulley.refitting is the revers sequence of removal, but before titgtening the muonting and adjusting arm bolt, tension the drivebelt.

Jan 16, 2009 | Mazda 323 Cars & Trucks

2 Answers

2004 ford freestar drivebelt


All you need is a 13mm boxed end wrench. The tensioner pulley is the one all the way on the bottom towards the rear of the van. You can reach it under the van. Slide under the van in front of the passenger front tire and you will wee the pulley. Put the wrench on the bolt and pull towards you to release the tension on the belt.

Jul 17, 2008 | 2004 Ford Freestar

Not finding what you are looking for?
1998 Dodge Stratus Logo

317 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...