Question about 1998 Mazda 626

1 Answer

I try to give my mazda throttle and it cuts out then stalls

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Welcome Back:

    Visited the website for 2 consecutive days.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 18 Answers

Sounds like an air leak on the intake to the engine, listen for a hissing sound while the engine is idling, probably the manifold gasket. Good luck

Posted on Jul 28, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My 2006 Mazda5 stalled then continued running yesterday after I got off the highway & check engine , on return the car stalled & stopped completely at red traffic light. What could be the cause and...


Possible loose air inlet boot off the air cleaner to the throttle body. Try taking it to a local Checker, Autozone or O'Rielys for a code pull which may give you a better idea of what is going on.

Dec 25, 2013 | 2006 Mazda 5

2 Answers

1999 mazda 626 lx engine stalls when put in any gear


It can be low fuel pressure issue or clogged fuel pump. Or its engine related issues,---------------
Check the help link mentioned below to troubleshoot the problem: ------

Engine stalls, car stalls while starting, vehicle stalls while starting, Engine stalls and dies, Car stalls and stops,
http://alltypesofpartsreplacing.blogspot.com/2012/12/engine-stallscar-stalls-while.html

------
These will help.
Thanks.

Dec 17, 2012 | 1999 Mazda 626

1 Answer

My mazda 626 at idle read 1500rpm. when moving it will suddenly stall, at times when moving slowing in traffic, it stalls. what can i do?


what model mazda?? check for a cracked air intake hose air filter to throttle body replace if cracked. It should only be idling at 750rpm

Aug 07, 2012 | 1994 Mazda 626

1 Answer

2000 MAZDA 626 LX 2.0 tries to die at lights or stop signs. Runs fine otherwise.


Engine stalling and rough run issue at low speeds

This problem is commonly caused by a dirty automatic idle speed control valve and throttle valve. Buy a can of throttle valve cleaner (do not use carburetor spray cleaner!) from NAPA or Carquest (made by CRC chemicals) and spray it into the air intake while the engine is running, use up about 1/2 the can, engine will try to stall hold the speed up, shut it down and let it soak for 30 minutes, restart and blow out the remaining fluid, shut it down and disconnect the negative battery cable for 5 Min's to reset the base idle control

Aug 06, 2012 | 2000 Mazda 626

2 Answers

My Mazda 6 car stalls when I stop, also crakig, I replaced throttle body and fuel pump


When you stop if the Mazda stalls try putting the car into neutral gear and see if it still stalls. if the Mazda does not stall in neutral then the torque converter has failed and needs replacing.

Sep 15, 2011 | Mazda MAZDA6 Cars & Trucks

1 Answer

My 93 mazda protege dx seems to be getting too much fuel. when it warms up and give it too much throttle it will stall. it does not burn oil, and there is no blown head gasket but when i start it first...


blue smoke is a sure sign of oil bleeding down from your valve seats (little rubber umbrellas inside the head on each valve) into or on top of the pistons after sitting over night..in most cases a good mechanic can do that repair with the cylinder head still on the car...the stalling is usually open close sensor ..TPS (throttle position sensor ) or spark plugs..both inexpensive easy fixes..GOD BLESS

Jan 29, 2018 | 1993 Mazda Protege

1 Answer

Was loping in drive, would have to put in neutral, now stalling in neutral, at first i thoght it was the fuel injector, not sure


engine runs smooth if giving more than idle pressure. It is when the motor is engaged with transmission at start the engine lopes and wants to cut off. If I press the throttle hard it takes right off. If I come to a stop I can put transmission in neutral to keep it from cutting off. This creates a shifting that is not normal and I'm afraid it is a sign of failure coming.

Sep 28, 2009 | 1990 Mazda 626

2 Answers

Mazda stalls


I have a 1997 626 2.0L 5speed when im driven it like rev limits cuts out around 3500-4000rpm, and when i rev it up and past 4000rpm it stalls, anyone have a idea whats wrong??? thanks i just replaced the crank sensor and egr and still. good power put cuts out

Jul 03, 2009 | 1997 Mazda 626

1 Answer

Mazda tribute 2002 stalling


1. will it stay running if you foot is sligtly on the gas.
if so common problem it the IAC valve located on top of the throttle body. it controls ait into the engine when throttle is closed.
2. do you hear loud fog horn like sound or hissing. this could indicate a vaccum leak.
3. are there any performance problems while driving.

my best guess would be the IAC (idle air control) valve

Jun 23, 2009 | 2002 Mazda Tribute

Not finding what you are looking for?
1998 Mazda 626 Logo

Related Topics:

153 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

Marvin
Marvin

Level 3 Expert

81423 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...