Question about 2001 GMC Yukon XL

2 Answers

How do I reset the CHANGE OIL light on my YUKON 2001 5.3 4x4

Posted by on

  • 1 more comment 
  • gruporeyesde Jul 12, 2009

    NO, IT DINT WORK...........

  • gruporeyesde Jul 12, 2009

    HOW DO I RESET THE "CHECK OIL" LIGHT ON MY YUKON 2001

  • gruporeyesde Jul 16, 2009

    thank you

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • GMC Master
  • 3,854 Answers

  1. Turn the ignition key to the RUN position but do not start the engine.
  2. Fully push and release the accelerator pedal three times within five seconds.
  3. If the CHANGE OIL SOON light flashes 2 times, the system is reset. If the light comes on and stays on for 5 seconds, the system did not reset. You may have to repeat the procedure a couple of times if the system does not reset.
Good luck and this should work, have a nice weekend friend.

Posted on Jul 11, 2009

  • Harvey N Tawatao
    Harvey N Tawatao Jul 12, 2009

    Chevrolet Suburban/GMC Yukon XL, 2000-05 Chevrolet GMC Trucks Silverado, Sierra, 1999-05 Chevrolet Venture 2000
    Turn the ignition key to the RUN position. Fully push and release the accelerator pedal 3 times within 5 seconds. If the CHANGE OIL SOON light flashes 2 times, the system is reset. However if the light comes on and stays on for 5 seconds, the system did not reset. Repeat the procedure if the system does not reset.

    Try it again here is the service from my cd



×

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,515 Answers

Hi,

Turn the key to the run position without starting. Press the accelerator completely to the floor three times within 5 seconds. The change oil light will begin flashing. This should reset it.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

Posted on Jul 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Change oil display


on yukon bring up display and either push to reset button or press and hold down the trip odometer button [dont know what year vehicle u have] and it will reset back to 100% also your manual has how to reset the oil as well

Mar 31, 2014 | GMC Yukon XL Cars & Trucks

1 Answer

How do you reset oilchange light on a 2001 yukon xl


turn key to on position, pump gas pedal to floor 5 times and turn off key. start vehilce. Change oil light should flash for 7 seconds and then go out.

May 15, 2010 | 2001 GMC Yukon XL

1 Answer

How to reset oil change light?


Make and Model: Chevrolet Suburban, GMC Yukon XL, Chevrolet Silverado, GMC Trucks Sierra
Years: 2000-01, 1999-00

Turn the ignition key to the RUN position. Fully push and release the accelerator pedal 3 times within 5 seconds. If the CHANGE OIL SOON light flashes 2 times, the system is reset. However, if the light comes on and stays on for 5 seconds, the system did not reset. Repeat the procedure if the system does not reset.

Hope this help (remember rated and comment this help) Good luck.

May 14, 2010 | 1999 GMC Sierra

2 Answers

2002 yukon set oil change light


Hello joecradd: My name is Roger and I will help you. With the key on engine off. Depress the foot feet 3 times with in 5 second. If the CHANGE ENGINE OIL flashes for 5 seconds, the system reset. Should you need further help please just ask. Please rate the answer. This way I know it was helpful. Thank You for using Fix Ya. Roger

Mar 21, 2010 | 2002 GMC Yukon Denali

1 Answer

HOW DO I RESET THE CHANGE OIL LIGHT ONCE THE OIL


look in the manual......turn the ignition to the on position not starting it of course and then pump the gas petal 5 times then the light will blink a few times turn off then back on...problem solved

Jan 30, 2010 | 2002 GMC Yukon Denali

1 Answer

How do you reset oil change indicator?


Chevrolet Service Light - For Chevrolet Suburban, GMC Yukon XL, Chevrolet Silverado, GMC Trucks Sierra 2000-01 and 1999-00:

Turn the ignition key to the RUN position. Fully push and release the accelerator pedal 3 times within 5 seconds. If the CHANGE OIL SOON light flashes 2 times, the system is reset. However, if the light comes on and stays on for 5 seconds, the system did not reset. Repeat the procedure if the system does not reset.

I really hope helps with this (remember rated this help) Good luck.

Jan 05, 2010 | 2000 Chevrolet Silverado

1 Answer

How to reset the change oil light on a 2003 chevy silverado


Information courtesy of synthetic-direct.ca
Chevrolet Suburban/GMC Yukon XL, 2000-05 Chevrolet GMC Trucks Silverado, Sierra, 1999-05 Chevrolet Venture 2000
Turn the ignition key to the RUN position. Fully push and release the accelerator pedal 3 times within 5 seconds. If the CHANGE OIL SOON light flashes 2 times, the system is reset. However if the light comes on and stays on for 5 seconds, the system did not reset. Repeat the procedure if the system does not reset.
Best of luck.
Greg

Jul 15, 2009 | 2003 Chevrolet Silverado 1500

1 Answer

How to reset computer showing percentage of oil life remaining


If it is anything like the 2003 you turn your car to the on position without running the engine, tap the accelerator 3 times very quickly in less than 5 minutes. This should reset your back to 0 for your next oil change.

Apr 03, 2009 | 2003 GMC Yukon XL

1 Answer

2008 yukon first oil change


THE OIL PAN IS GOING TO BE THE LARGEST PAN AT THE BOTTOM OF THE ENGINE. THERE WILL BE ONLY ONE PLUG ON IT. TO RESET THE OIL CHANGE REMINDER FOLLOW THESE STEPS. TURN THE KEY TO THE ON POSITION, BUT DO NOT START THE VEHICLE. WHILE THE KEY IS ON PUSH THE ACCELERATOR PEDAL ALL THE WAY TO THE FLOOR THREE TIMES. THIS WILL RESET THE OIL REMINDER.

Jan 24, 2009 | 2008 GMC Yukon

1 Answer

2000 yukon xl


turn the key to the run position engine off, push the gas pedal all the way to the floor then release it 3 times within 5 seconds, the DIC will say oil life reset.

Nov 05, 2008 | 2000 GMC Yukon XL

Not finding what you are looking for?
2001 GMC Yukon XL Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

Marvin
Marvin

Level 3 Expert

81423 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...