How do I remove door panel on a 2009 VW EOS?

SOURCE: How do I remove the door panel?

the door handle pops off with a small screwdriver....the part on the door panel where you grab to pull it shut....then there are 2 screws behind there and 3 screws on the bottom....the door lifts off.

SOURCE: How do you remove inner rear door panel from 1997 VW Golf?

well you need to start looking for screws and little covers on the trim panel / then and one should be around the handle/ then youpull form the bottom and work the same on the sides than pull from the bottom and pull it up and out as you take the trim off then disconnect the wire connector and you can see where everything is and remove the vapor barrier/ Please rate my response thank you very much

SOURCE: door panel

here is a diagram of how to unistall your door panel. please do not forget to rate and comment about your experience with fixya today.

Driver's Side Door
NOTE This procedure is for models with power windows. If equipped with manual windows, refer to the procedure for the Passenger Side Door Panel.


NOTE Do not grasp in grip depression when pulling off grip recess, as there is a strut secured to door trim underneath.

1. If necessary, make sure you have the radio code.
   
2. Make sure the ignition if OFF, then disconnect the negative battery cable.
   
3. Insert a suitable prytool in lower partition between the panel and grip recess.
   Insert a suitable prytool in lower partition between the panel (1) and grip recess (2)
   
4. Unclip the grip recess upward out of door trim. Do NOT reach into grip depression while doing so, to prevent damage to brace.
   
5. Press the locking lug against the connector (3 – arrow) and pull it off.
   Unclip the grip recess (2) upward out of door trim. Do NOT reach into grip depression while doing so, to prevent damage to brace (1). Then , press the locking lug against the connector (3 – arrow) and pull it off
   
6. Unscrew the 7 mounting bolts.
   
7. Unclip the door trim at the sides using disassembly pliers 3392, or equivalent.
   
8. Lift the door trim up out of window recess.
   Unfasten the 7 bolts (arrows). Use pliers to unclip the door trim (1) at the sides, then lift the trim up out of the window recess
   
9. Unclip the cable guide using a prytool, pull out the bracket in the direction of the arrow, then unhook the cable hook.
   Unclip the cable guide (1) using a prytool (2), pull out the bracket (3) in the direction of the arrow, then unhook the cable hook (4)
   
10. Disconnect the connectors and remove the trim panel from the vehicle.
    View of the driver’s side door panel—with power windows
    

1. Pull off the window recess seal from door trim and insert in window recess.
   Pull off the window recess seal (1) from door trim and insert in window recess
   
2. The remainder of installation is the reverse of the removal procedure, noting the following:
   
   • Before installing door trim, check all clips and replace as necessary, and insert into mounts of door trim.
     
   • After connecting battery, check that the vehicle equipment (radio, clock, electric windows) is operating properly.
     
   • If the Electronic Control Module (ECM) is subject to low voltage with ignition on, DTC memory and Readiness code must be checked with a scan tool.
     

SOURCE: Removing door panel of manual crank 2000 VW Beetle

Your window crank is held on by a clip at the base of the crank handle. You need a small hook (kind of like a knitting needle) to get behind the base and pull the clip off of the crank.

I hope this helps you, and I wish you luck on your repair.

SOURCE: Interior trim panel removal instruction

Normal 0 . Disconnect your negative battery cable. Locate and remove the screws that hold your interior door handles in place (they may be hidden by snap in, or snap on clips). Remove the interior door handles, then disconnect the wire clips to the switches. Your panel is held in place by snap in clips; use a small pry bar to pull them from the door (try to get as close to, or directly under the clips to prevent them from tearing out of the door panel). Once the clips are pulled, pull the panel upward to remove it from the door.
Install in reverse.

If you don't have power windows you will have to remove the manual window crank. It is held in place by a clip on the back side of the base. To remove the clip, you will need a small hook (kind of like a knitting needle). Put the hook in behind the base, and grab the clip and pull it off. To replace it, slide the clip back on the window crank, and snap it back on the door.