Have the radio code 4514 instruction turn key on first position eee reading enter code but it doesn't enter. How do you enter the code

. Every time you disconnect the battery means that the radio thinks some one is stealing it so the anti theft code kicks in. Next turn on the ignition to accessories or the run position and either turn the volume knob or push it in . The radio dial will light up and ask for a code . Enter that code as per the instructions and then the radio will work. If the radio dial doesn't light up check for fuse and wiring problems

Remove the postive battery from the battery touch it to the negtive for 20 secs and reconnect this will reset all computers to factory settings..
Enjoy you tunes!

put a battery charger on the battery,turn key to on postion[engine not running] turn radio to on and let it sit there like that for about 5 hours or untill radio say code then enter right code. if battery goes dead during this you have to dtart over

if you punch in 3 consecutively with a wrong code, the EEE message will be displayed. in order to erase this, you need to place your ignition key at # 1 and switch on the radio and leave it at least between 4 to 6 hours. the code display will come back and re-enter the correct code.

Ford Code Entry Instructions
Once the unit has been turned on the display will show ' CODE - - - -'
Press preset [ 1 ] repeatedly for the first digit
Press preset [ 2 ] repeatedly for the second digit
Press preset [ 3 ] repeatedly for the third digit
Press preset [ 4 ] repeatedly for the third digit

To save the code press the [ 5 ] key to accept.
The set should now operate

This is the anti-theft device on your factory radio. When the battery died, the radio thought it had been removed from your car and went into anti-theft mode. When you turned the car back on, the radio should have read "CODE" on the display, at which point you need to enter the factory anti-theft code. After 3 failed attempts at entering the code, it will simply read "OFF" and the radio is locked.

At this point:
- find your factory anti-theft code - it should be in your owner's manual, or you can contact a dealer to retrieve it
- turn the key to the ACC position (radio and accessories on, but engine is off)
- turn on the radio so the display reads "OFF"
- let the car sit for 1 hour
- radio will turn off automatically and reset
- turn the radio on again, and it should read "CODE"
- enter the factory anti-theft code

Make sure you have the code before starting the procedure. To enter the code, use the radio preset buttons. For example, if your code is "4321", hit Preset #1 button four times, Preset #2 three times, Preset #3 two times, and Preset #4 one time. Then hit the "Tape" or "CD" button. Radio should now be unlocked.

Hello,

There is a trick to the procedure. You have to turn the key to position 1 or the first stop on the ignition. Turn on the radio and wait between 2.0 to 3.0 hours for the radio to reset and ask for the code. From the owners manual. My 97 takes between 2:25 and 2.5 hours to reset. Every radio is different.

To enter the code:

After installation or when the set has been disconnected from power, the set displays "codE" when it is switched on.
Enter the 4-digit code using the preset buttons. If the correct code is entered, "on" is displayed and the set is ready to use.
If you enter an incorrect code you must enter the correct code again from the beginning.

Incorrect code

If an incorrect code has been entered "rPt" is displayed. Enter the correct code.
After three unsuccessful coding attempts the set will lock and remain locked for two hours.
"OFF" is displayed.

During this waiting period:

the battery must be connected
the ignition key must be turned to position I
the unit must be turned on
Make sure the headlights are turned off to help prevent battery drain (please refer to page 2:6 for information on turning the headlights off). Enter the code again once this time has elapsed.

Goodluck!
Ryan

You have to turn the key to the very first position (do not start car) and leave on for 1.5 hours, then come back and enter your code. Sounds crazy but it works.

take it to an acura dealer and they can unlock the radio for you if you don't have the code.

the dealer will reset it. Im guessing they will charge you though