Question about 2003 Hyundai Tiburon

1 Answer

Location of the Purge Control Valve for 1998 Hyundai Tiburon

Posted by on

  • da_hun Jul 12, 2009

    but where is the valve located????

  • da_hun Jul 16, 2009

    the "Canister Control Valve" is located near the back of the engine compartment on the right hand side. it is a little black plastic container with an in and an out what appear to be 1/2" hose connectors (similar to a pcv valve). also, there is the wiring leads that connect on the out ------> side. the Unit itself has the letters PCV embosed on it ; althought this is not the positive crankcase valve.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 580 Answers

The correct "Hyundai" term for the valve that's attached to the Vapor Canister is the "Canister Control Valve".Why don't you try to clean the old one first. They get clogged with little bits of charcoal from the canister. It's simple so see if it's bad, take it off, and try to blow through the canister side with no electric going through. You shouldn't be able to blow because the valve is supposed to be closed. If you can blow it's because the valve is clogged and hanging open. If it is clogged, you might try and clean it.

Then take the hose off from the canister and clean the hose too, you'll get a handful of charcoal out before your done. If you don't clean the hose out, you'll probably clog the valve again, even if it's new.

That's why they usually change the canister and the valve at the same time. It gets clogged because you fill the tank to the max, it floods the canister with gas, and the charcoal floats up through the hose to the valve.

Posted on Jul 11, 2009

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
ghost4548
  • 776 Answers

SOURCE: Location of the Purge Control Valve for 2003 Hyundai Tiburon

There were two different engines which were installed in the 2003 Tiberon... the 2.0 liter 4 cylinder:
22c99c7.jpg

And the 2.7 Liter V6:
cb31feb.jpg

Posted on Jun 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 hyundai santa fe 3.5L purge valve location


Check under the auto for the evaporation canister.The purge valve should be @ the engine side of the canister.

Dec 27, 2017 | Hyundai Cars & Trucks

2 Answers

Overheat 2001 hyundai tiburon


Only 2 parts remaining are the thermostat and waterpump. Always start with the thermostat when diagnosing an overheating problem. If the car is overheating constantly under all conditions and coolant is backing up into the reservoir, it's very likely to be the thermostat. If it only overheats at low speed or idling, it's more likely the waterpump.

Aug 11, 2009 | 1998 Hyundai Tiburon

1 Answer

Purge valve location on a 2003 tiburon 2L


On your Tiburon the purge valve is located below the throttle body. It is easier to access if you remove the boot between the airbox and the throttle body. After removing the boot look under the throttle body, the purge valve will be found mounted in a rubber hangar and it has a vacuum hose to both ends.

Jul 03, 2009 | 2003 Hyundai Tiburon

1 Answer

Location of Purge Control Valve on 2003 Hyundai Tiburon GT


Go to http://www.hmaservice.com/ and register (vehicle by VIN). Afterward, you'll have access to technical information (manuals, wiring diagrams, service bulletins, etc) about your vehicle.

Jun 09, 2009 | 2003 Hyundai Tiburon

1 Answer

Location of the Purge Control Valve for 2003 Hyundai Tiburon


There were two different engines which were installed in the 2003 Tiberon... the 2.0 liter 4 cylinder:
22c99c7.jpg

And the 2.7 Liter V6:
cb31feb.jpg

Jun 06, 2009 | 2003 Hyundai Tiburon

1 Answer

Code error P0441


this code refers to EVAP Emission Control System Incorrect Purge Flow, it can be tricky to diagnose because of the number of parts, I would first check the vacuum hoses between the purge valve and the air cleaner, then the purge valve and the canister, also check the fuel tank vent and fuel cap valve and gasket. any one of these can cause this check engine code. after checking this I would reset the computer and see if it comes back.

Apr 13, 2009 | 2004 Hyundai Tiburon

2 Answers

Check engine light on , code po443 1998 sonata


To cause a P0443, there has to be a problem with the purge control CIRCUIT, not necessarily the valve. Usually they are a unit housing the valve and the solenoid as an assembly. Or it could be comprised of a separate solenoid with vacuum lines to a purge valve. That said, it could be any of the following:
  • Bad purge solenoid (internal short or open)
  • Wiring harness chafing or rubbing another component causing short or open on control circuit
  • Connector worn, broken or shorted due to water intrusion
  • Driver circuit inside powertrain control module (PCM) is bad
I would just clear out the code and if it returns then try the above. Hope this helps you a little bit!

Sincerely,

JC

Nov 15, 2008 | Hyundai Motor 1998 Sonata

1 Answer

Location of Charcol Canister and EVAP Emission control solenood valve in hyundai elentra 2002.


The evaporative emission canister purge solenoid valve is a duty control type, which controls the flow of purge air from the evaporative emission canister.
4a6acf4.gif Inspection 1. Look for loose connections, sharp bends or damage to the fuel vapor lines. 2. Look for distortion, cracks or fuel leakage. 3. After removing the EVAP canister, inspect for cracks or damage. 0e0e1be.gif

Sep 03, 2008 | Hyundai Elantra Cars & Trucks

Not finding what you are looking for?
2003 Hyundai Tiburon Logo

771 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

Marvin
Marvin

Level 3 Expert

81285 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...