Question about 1998 Chevrolet K1500

1 Answer

Will not **** into 4 wheel drive 4high, will go into 4 low. I have replaced dash switch, switch on top of transfer case, tranfer case motor, and control module

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Chevrolet Master
  • 81,400 Answers

THE PROBLEM IS IN THE 4X4 TRANSFER CASE THEY GET "JAMMED", IF U HAVE NEVER CHANGED THE FLUID IN THE TRANSFER CASE DO SO, IF THAT DOESN'T CURE THE PROBLEM YOU WILL NEED TO REBUILD THE TRANSFER CASE.

Posted on Jul 11, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 Chev Silverado, 2500, 6.0 engine, auto trans with manual engage 4 WHD. 4 wheel drive does not work


You have a switch on the instrument panel ?
The NVG 263 transfer case features a three button shift control switch located on the instrument panel
The NVG 236/246 transfer case features a 4 button shift control switch located on the instrument panel.
Or
The New Venture Gear (NVG) 261, RPO NP2 transfer case is a two-speed, part-time with "mode shift-on-the-fly" capability. It has a chain driven front output shaft and an epicyclical low range planetary arrangement. The NVG 261 transfer case features a four position shift lever control located in the vehicle floor plan. As required, the operator can select 4HI position from 2HI "on-the-fly," as described in the owners manual. A dash 4WD lamp will continue flashing during shifting, until all criteria have been met and the new mode/range position has been reached. Once the new mode/range position is fully engaged and the front axle disconnect locks in, the dash light 4WD indicator lamp will remain ON constantly. Range shifting functions similarly, although it should be limited to speeds 8 km/h (5 mph) or less.

Feb 11, 2018 | Cars & Trucks

1 Answer

2000 chev Silverado 1500 push button 4 x 4 will not come out of four wheel drive. No 4 x 4 service lights on. Dash switch indicates 4 high. Push for 2 wd. the light in dash will go from 4high to 2 high...


Seems if i remember it could be one of two things. The control module is located right behind the dash on the left side of the steering column close to the ac vent. So close that condensation from the AC runs into the plug. The only other thing is the motor on the transfer case. You cold remove the motor and plug it up and get someone to move the switch for you. Don't forget to ground the motor while testing it.

Oct 29, 2017 | 1999 Chevrolet Silverado 1500

1 Answer

My four wheel drive is not working. i replaced the switch on the dash. tried it and all it did when i hit 4-hi both 4-hi and 4-lo blink a few times the it goes back to 2 wheel drive. it did stay in 4-hi...


It's the transfer case motor.I had the same problem exactly and replaced, now it works great. Part is about $100.00 ( aftermarket ) .Ifyou are going to replace yourself you will have to remove front drive shaft and remove yoke from transfer case with an impact wrench for clearance to remove transfer case motor . When you put the new transfer case motor in make sure you line up slot with grove in transfer case motor. Good Luck.

Jan 03, 2011 | 1997 Chevrolet Blazer

1 Answer

Just replaced my encoder motor, front actuator, and dash switch....altough the transfer case engages it won't stay in 4 wheel drive for long


you may have to replace your trasfer case control module its right under dash driver side easy to access mine just went out it was throwing c0359 code 4 low cirut and service four wheel drive would come on dash although the 4wd works great it just throws the code.

Jan 01, 2010 | 2003 GMC Sierra

1 Answer

LAST WEDNESDAY WHILE OUT ON THE BACK ROADS, I DECIDED IT WOULD BE A GOOD TIME TO RUN THRU MY 4 WHEEL DRIVE (ELECTRONIC 2H, 4H, 4L, & ALL WHEEL), ALL OF THE SHIFTS WENT FINE, AND I THEN DROVE HOME. IN...


sounds like you have a combonation trans and transfer case issues. if you were running youre truck in four wheel on a hard dry surface, witch is not recomended , the trans probibly ran hot. as for the transfer case, it could be a combination of problems. dash switch/ actuator/vacum switch/ vacum canister witch is under the battery tray. all have to work in unison. service the trans first. if the truck has high miles, add trans conditoner, if you do not, it will slip. then the transfer case. refer to youre owners man for oil specs. youre problems are not uneque as these trucks are notorius for unreiable four wheel actiuation. hope i was some help.

Oct 27, 2009 | 2000 GMC Jimmy

1 Answer

I have a 2005 Ford F150 4x4 crewcab. I can not


Is the 4 wheel light flashing on the dash. If so the problem could be in the computer if it is electronic 4 wheel drive. It can also be the motor on the transfer case or the switch on the dash. You can check the switch on the dash and see if you are getting power to it and out of it. Then you can check and see if you are getting power to the motor on the transfer case. If you are getting power in the switch but none coming out of it when switch to the 4 wheel drive position it is the switch but if you are and are getting power down to the motor on the transfer case it is the motor on the transfer case. If you are not getting power to the switch then it is in the control computer for it mounted in the dash behind the radio.

Sep 13, 2009 | 2003 Ford F150 Regular Cab

1 Answer

4 wheel drive


small switch isnt working right on the top of transfer case. vacome operated. replace or check the three lines that run to it

Dec 06, 2008 | 1993 Chevrolet S-10 Blazer

2 Answers

06 F150 4 four wheel drive wont work


I have a 1994 ford f150, my 4 wheel drive keeps trying to engage by itself even without me touching the automatic hub button....at time you can even hear it engaging and disengaging by itself, the low range light even comes on (dimly)...what could be the cause? the transfer case motor looks good and so does the wiring.

Nov 28, 2008 | 2006 Ford F-150

1 Answer

88 Bronco ii won't shift into 4 wheel drive.


Check to see if you are getting power through your switch on your dash. I also suspect your shift motor but it is a lot easier to check it with a test light.

Jul 01, 2008 | 1988 Ford Bronco II

Not finding what you are looking for?
1998 Chevrolet K1500 Logo

Related Topics:

101 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...