Question about 2000 Kia Sephia

1 Answer

Replacing door handle

How do you replace inside door handle on drivers door?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

Take door apart there should only be one screw to get outside cover off handle. when the door is apart there are three screws for the latch and two rods that disconnect (one for the latch and one for the lock)

Posted on Jul 16, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why won't the drivers inside door hand work


Sounds like your rod is disconnected. Or its stuck in lock

Aug 24, 2014 | 1998 Toyota Camry

1 Answer

Why won't my driver door open from the inside?


Door handle is disconnected to the lever because the parts are plastic it could break easily common thing

Aug 24, 2014 | 1998 Toyota Camry

1 Answer

Replacing driver side door handle


First, ya gotta remove the interior door panel....

Door Panel
  1. Fully lower the door glass.
  2. Remove the arm rest, door lock knob and inside door handle escutcheon.
  3. Remove the regulator handle.
  4. Gently pry the door panel away from the door.
  5. Installation is the reverse of removal. Install the regulator handle (correct position) with the door glass closed.
Next you'll need a small ratchet and extenstion with socket...or a socket driver (like a screwdriver but holds a socket). Remove the two nuts attaching the handle to the door. Use a long thin flat screwdriver and pop loose the clip attaching the rod to the lock mechanism..
Manuever the handle off the door and then install in reverse order.

May 28, 2010 | 1987 Nissan Pickup

1 Answer

Driver side handle replacement


in most vehicles, replacing the handle entails removing the inside of the door to access the mechanisms inside. there usually isn't a way around this. a repair manual can assist with directions on how to go about doing this type of project.

Apr 28, 2010 | 1999 GMC Suburban

1 Answer

I need to replace the REAR door handle on my 98 Toyota Seinna Van Do I take apart the inside door panel or pop off the outside cover?


the inside door panel. you need to removethe assist grip and door pull ******** the lift gatetrim panel (you'll need a 10mm socket)use a flat screw driver to carefully pray all around the the panel and then pull it off. you should be able to see the handle and youll know what to do depending if you are replacing just the handle or the whole latch. good luck

Jan 05, 2010 | 1998 Toyota Sienna

1 Answer

Need help on replacing door handle on toyota camry for the front driver side..


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. If it's the inside handle, just disconnect the rod to the back of the handle to replace it. If it's the outside handle, pull back the weather seal and you'll be able to remove the bolts holding down the outer door handle

Sep 14, 2009 | 1995 Toyota Camry

1 Answer

Replacing the driver side inside door handle


Find and remove two screws visible on the door panel, including underneath small covers. Pop them off with a small screwdriver. Lift front edge of control panel, then pull forward and lift out. Pull upper door panel from door. Disconnect courtesy light connector. Disconnect door open handle cable assembly and door lock cable assembly. You might need to lift panel and twist to get it off.

Feb 23, 2009 | 1998 Lexus Sc 300

Not finding what you are looking for?
2000 Kia Sephia Logo

438 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Marvin
Marvin

Level 3 Expert

81294 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...