Question about 2004 Mercury Mountaineer

1 Answer

Ticking in motor, then stops for about a month, then starts ticking again. oil changed. in nuetral it wont rev past 3500 rpm

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 365 Answers

It wont rev past 3500 in driving?
The governer on these is set to NOT allow a higher rev when car is stopped and not in gear.
Try to change oil viscosity or filter manufacturer.Some filter manufactures put in a bypass valve that kicks in too early.

Posted on Aug 04, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Daewoo leganza wont rev past 2800 rpm idles fine just wont rev past 2800 ?


In park, this could be normal. ECU does this. around 2800 to 3500 RPMs. If driving, have the codes read. No codes , could be a clogged fuel filter, bad fuel pump(have the pressure checked), or clogged catalytic converter/s. With no codes, something is restricted..

Jun 10, 2016 | 2001 Daewoo Leganza

2 Answers

Cutting out at 3500 rpm


Check if the air filter is clogged with oil and dirt. Check the timing, then check that the cam belt has not slipped. Could be plug wires, but this will usually cause rough running as well. Could be low fuel pressure.

Mar 01, 2014 | 1991 Honda Civic

1 Answer

Ticking clanking noise miata


This noise you hear is the hydraulic tappets ,there gummed up change the oil and use a cheap diesel/petrol engine oil a 2 second squirt of fairy liquid into the oil filler and leave for a couple of thousand kms then change the oil again and this will clear the gummed up holes allowing the hydraulic tappets to re adjust

May 23, 2013 | Cars & Trucks

1 Answer

A ticking sound on a 06 ford f150 super crew 5.4L


Ticking sound could be coming from a Coil-on-Plug, or a pcv valve, or (hope it's not) a valve lifter which could be sticking. Sticking lifter noise often disappears when rpm's change, or the noise comes & goes. try changing the motor oil & filter right after adding an Engine-Flush Treatment to the motor oil, running the engine for 10 minutes at idle with treatment added to the oil, then draining the oil & changing filter while oil is still very hot. That last part is very important, so be careful not to burn your hands - be careful. -- The sticking lifter is a likely cause if motor oil has not been changed at frequent intervals in the past (every 3-4K miles) -- dirty oil causes sticking lifters.

Aug 10, 2012 | Ford Cars & Trucks

1 Answer

Only has 2nd and third gear? and wont go past 3500 rpm dont know what it is


2 problems do not inter react , 2 and 3 gear relates to clutches or syncros or badly allined shift gear , 3500 revs points to gas problem of filter prob

Mar 22, 2012 | 1991 Honda Accord

1 Answer

Wont move in drive.but if you put it in nuetral and rev the motor to1200 rpm and dop it in drive it works fine until you stop again


oil level low ,start engine ,handbrake on then select reverse and then check oil level ,think you are about at a least a litre short

Dec 23, 2010 | Subaru Legacy Cars & Trucks

1 Answer

Recently replaced the transmission with one from a salvage yard. I have to rev the motor in nuetral before transmission will engage after I do that it works as it should, except when I come to a complete...


low transmission fluid level about a litre and a half should cure it at a rough guess ,start engine ,handbrake on then select reverse and then check oil level it definatly sounds low to me

Nov 03, 2010 | Chevrolet Lumina Cars & Trucks

1 Answer

1991 honda ACCORD WONT REV PAST 3500 RPM NO MATTER IF YOUR IN PARK OR DRIVE OR NEUTRAL BUT IF YOU SHUT IF OFF AND ON AGAIN IT RUNS FINE, i CHANGED FUEL FILTER, PLUGS AND AIR FILTER, AND i'M JUST CONFUSED...


the ignition control module may be going bad. call your local honda dealer with your vin # they had a recall on the control module for 91-93. they will tell you if yours was replaced already if not you can pick one up for $60 at autoparts store and it is located inside distributor

Jul 29, 2010 | 1991 Honda Accord

1 Answer

Engine is not ticking over at the correct RPM


first try using redexe fuel additive (a full bottle to 5gallons)to clean injectors/fuel pump.
your car has a fuel cutoff valve,saves fuel when coasting(over 1800 revs,if you put car in nuetral going down hill you use fuel,so you are wasting fuel in neutral.but you have read the handbook cos it tells you in there.......

Jul 02, 2010 | 2000 Daewoo Leganza

1 Answer

1990 1.5l wont rev past 3500rpm's


Honestly I wish I could offer you more info, if it revs now that eliminates the convertor, only I can figure is when you got it to rev you were "blowing the soot out" LOL I hope I have helped you some if so please rate me accordingly.

Dec 16, 2008 | 1990 Honda Civic

Not finding what you are looking for?
2004 Mercury Mountaineer Logo

Related Topics:

243 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

gerry bissi

Level 3 Expert

4376 Answers

Marvin
Marvin

Level 3 Expert

81285 Answers

fordexpert

Level 3 Expert

5687 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...