Question about 1999 Ford Explorer

Open Question

Need a wiring diagram for a 1999 Ford explorer 6 cyl engine

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
mixmaster
  • 626 Answers

SOURCE: 1999 ford explorer car stereo install

Heres the whole list. 1999 Ford Explorer Constant 12V+ Light Green Switched 12V+ Yellow/Black Ground Black Illumination Light Blue/Red Dimmer n/a Amplifier Remote Blue Antenna Right Front Front Speakers 5" x 7" Doors Left Front (+) Orange/Light Green Left Front (-) Light Blue/White Right Front (+) Dark Green/Orange Right Front (-) White/Light Green Rear Speakers 5" x 7" Rear Doors Left Rear (+) Gray/Light Blue Left Rear (-) Tan/Yellow Right Rear (+) Orange/Red Right Rear (-) Brown/Pink (from the12volt.com) Best of Luck.

Posted on Sep 29, 2007

Ad
  • 1 Answer

SOURCE: I need a diagram for 1994 ford explorer transmission

hey whats up go to any auto parts store and ask them for either the haynes book or chilton book for your vehicle

Posted on Dec 24, 2008

  • 6982 Answers

SOURCE: Need schematic of tachometer; housing says MY89 6

Tachs are really not that expensive... problem with the tach from your jeep is that it's not connected to the ign coil in a traditional sense, instead, it is connected to the engine control module, which may contain part of what would normally be found inside a seperate unit, making your tach, basically a volt meter with a different scale on it.
Before taking it apart and rendering it useless for anything, I'd get a tach made for use on the vehicle you intend to put it in.

Posted on Feb 17, 2009

bschilz
  • 2049 Answers

SOURCE: I need the diagram for serpentine belt routing on

Here's the diagram you asked for...

85cf64b.jpg

Posted on Jan 25, 2010

  • 834 Answers

SOURCE: 1966 ford f100 inline 6 cyl 300\r\engine turns

Make sure that the primary wire between the distributor ignition points and ignition coil is not damaged anywhere and grounding the circuit out. This is not a ground wire.

Replace the ignition points condenser, if this is shorted your points will never be able to work. With the condenser removed, use an ohm meter to check the resistance between the end of the condenser wire and the condenser caseing, there should be infinite resistance or an open loop, but it should not show any kind of a connection between the two, or it is grounded or "shorted to ground" and it will prevent the ignition system from working.

Are the ignition points adjusted properly? They have to open and close to send a dwell signal to the coil.

Connect a test light to ground and on the NEG. (-) side of the coil, have someone crank the engine and look for the test light to flash, the test light should flash indicating a dwell signal or coil pulse. (Do not use the POS. + side of the coil for this test, because you will not get a dwell signal).

If no dwell signal, then...

1. Turn off ignition and remove the distributor cap and turn the engine over until a high spot on the distributor cam lobe is on the rubbing block on the ignition points.

This is the fully open position for the ignition points and where they need to be to set them. and if you do not know the feeler gauge size, or the dwell angle to set your points at (according to manufacturers specifications), then tear off a piece of a match book and place it between the two point breakers.

2. Loosen the point hold down adjusting screw and move the base of the points with a screwdriver (look for adjusting nothches), until there is a light drag felt pulling on the match book. For the newer GM's up to 1974, just use a 1/8 allen wrench to obtain the same light drag on the match book.

3. Remove the matchbook and there should still be a small gap between the point breakers, rotate the engine and you should see the points open and fully close.

4. Pull the coil wire out of the distributor cap and ground the end of the coil wire well or you might get shocked.

5. Have someone crank the engine and re-check for a dwell signal, you should also see a blue-white spark flashing between the point breakers as they open and close.

If you now have a dwell signal then replace the distributor cap back onto the distributor and the the coil wire back onto the distributor cap, the engine should now start.

If you did not grease the rubbing block of the ignition points with die-electric grease when you installed them, then the rubbing block on the points will wear down prematurely, the points will close down, and the engine will no longer start.

If you crank your engine over and the ignition rotor turns clockwise (looking down at the rotor) then you need to put the die-electric grease along the right side of the rubbing block edge (looking down at the points) so that the grease is trapped between the points and the distributor cam lobe, and the distributor cam lobe can pick up the grease. (Grease the left side of the rubbing block edge if the ignition rotor turns counter-clockwise). Only use die-electric grease.

Posted on Apr 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

96 ford explorer Manual trans. 2 door 6 cyl. 2 wheel drive repair diagrams


As per what you requested Transmission to engine bolts: 35 lb-ft (E/MWM).

But if you need more torque specs for other parts of your vehicle.I suggest you to check the link below with complete torque specification list and helpful diagrams.
http://www.allcarhelp.com/2016/05/torque-specs-for-bolt-size-of-bolts.html
This will help.
Thanks.

May 08, 2016 | 1996 Ford Explorer

2 Answers

After testing the MAF sensor, changing the PCV & CO sensors, I still get the check engine light, 1999 ford explorer sport 4.0 SOHC 6 cyl I've read to check the intake manifold and then go fu


What is a CO sensor? Never heard of it. a 1999 OBD2 ford has approximately 1600 possible fault codes most of which can turn on the light. If you dont know which one is turning it on, you are guessing randomly which is expensive and usually unsuccessful. get the code(s) and then diagnose the possible causes. The vehicle you list (99 4L explorer) rarely had injector problems. Much more common were EGR sensor(DPFE) sticking at voltage, evap problems, misfires, and lean conditions due to dirty MAF, or vacuum leaks. get the fault code, or you will not fix the problem.

Dec 29, 2012 | 2007 Toyota Land Cruiser

1 Answer

Which is bank 2 for the o2 sensor for post cat?


HiI!!
6 cyl. and 8 cyl. engines are divided into 2 Banks, standing in front of the Engine, the Bank 1 is the side where the #1 spark plug is (on V6 Ford Engines is on the PASSENGER SIDE). Bank 2 is on the DRIVERS SIDE.
Check the following diagram for HO2 sensor locations (This diagram applies to Ranger, Explorer and Mountaineer models) :
1kbron_121.gif


2 would be Bank 1 and 2A would be Bank 2.
Good Luck!! A HELPFUL - 4 THUMBS - rating for this solution would be greatly appreciated. Thank you for using FixYa.

Feb 15, 2011 | 1998 Ford Explorer

2 Answers

2000 ford mustang code 453 and missfire cyl 5 where is the cyl


a haynes manual from a parts place will show you--or chec the condition of each plug wire-if one looks bad or falls apart--probly need to get all new wires /plugs

Dec 18, 2010 | 2000 Ford Mustang

1 Answer

Changed plugs and plug wires in 1989 F 150 and it runs rougher than before need diagram


V8 engines as follows:

289,302,5.0L(Carb.)
390,406,427,428
400,460

(cyl numbers)

Front (engine)
5 1
6 2
7 3
8 4
(firing order)
1-5-4-2-6-3-7-8


5.0L EFI
351, 5.4L, 5.8L

(cyl numbers)

Front (engine)
5 1
6 2
7 3
8 4
(firing order)
1-3-7-2-6-5-4-8

Hope this helps, let me know.

Aug 03, 2010 | 1989 Ford F 150

4 Answers

How much oil do i put in a 1999 ford explorer when i change


1999 FORD TRUCKS EXPLORER 4.0L 6-cyl Engine Code [E] SOHC
Engine Oil Grade 1......API* All TEMPS......5W-30 Engine, with filter..........4.7 liters
1999 FORD TRUCKS EXPLORER 5.0L 8-cyl Engine Code [P]
Engine Oil Grade 1......API* All TEMPS......5W-30, 5W-20 approved for this application per Ford TSB 02-1-9 Engine, with filter..........4.7 liters
Here's the information your looking for and thank you for using Fixya





Mar 10, 2010 | 1999 Ford Explorer

1 Answer

Oil sending uint where is it at


Need to know if you have a 4 cyl or 6 cyl and the exact engine size. The sensor is in different a location for each one.

Jan 21, 2010 | 1999 Ford Explorer

1 Answer

I have just gotten a 99 expl. runs but not right changed 1 os that was bad. but still has a missfire trying to troubleshoot looking at sparkplug wires they don't look like the picture/diagrams in chilt...


It could be intake gaskets. Ford had problems with that in those years there's a update kit available from Ford for less than $100. It's not too bad of a job, you even have drain the coolant down.

Nov 09, 2009 | 1999 Ford Explorer

2 Answers

1993 ford explorer - toublshooting fuse/electical problem


I believe the fuse for your starter is in the power distribution box, 93 explorer 4.0L 4X4. find diagram for this in Chilton Ford Ranger/Explorer/Mountaineer 1991-1999 Repair Manual 26688 page 6-43 Fig.88 Be aware that there are (4) figures for the 93 4.0L explorer and each shows a different part of the same engine wiring. See top right 'power distribution box' follow lines to the part of your engine you are concerned with, which fuse number, then look inside your engine, passenger fender, push down on the protective ?wall then pull the cover up, see your diagram and fuse numbers. The diagram for inside fuse box, page 6-31 fig.63 I hope this helps

Jul 05, 2008 | 1993 Ford Explorer Limited

Not finding what you are looking for?
1999 Ford Explorer Logo

Related Topics:

352 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

gerry bissi

Level 3 Expert

4376 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...