Question about 2004 Acura TSX

Open Question

2004 acura tsx drivers side headlight works intermittently, inverter probably going anyone know where i can find refurb or used parts for this?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 23 Answers

SOURCE: 2004 Acura TSX Xenon light works intermitently

99% of the time the invertor is the problem with that condition

Posted on May 02, 2009

Ad
  • 4 Answers

SOURCE: 2004 acura tsx 6cd changer jammed

I CAN HELP YOU GET THE CODE OFF YOUR RADIO NEED TO REMOVE RADIO AND AND WRITE DOWN SER# AND EMAIL ME BACK AND I CAN HAVE YOU A NUMBER YU TYPE INTO RADIO AND IT WILL TURN ON LET ME KNOW

Posted on Jul 15, 2008

jpstuhr
  • 49 Answers

SOURCE: Replacing HID headlight in 2004 Acura TL

HID Bulb Replacement

A transient high tension (25,000 V ) occurs at the bulb sockets of the high intensity discharge (HID) lamps when the combination light switch is turned ON, it may cause serious electrical shock or electrocution if you do not observe the cautions below.

CAUTION:

  • Never turn on the combination light switch before fitting the HID bulbs to their bulb sockets and completing the reassembly of the headlight assembly.
  • Do not service the headlights assembly in wet conditions, such as rain or snow, near a sprinkler system, or when your hands are wet to prevent electrocution.
  • Do not touch the surface of the HID bulbs with your bare hands and do not stain it with any oils and fats.
  • Do not disassemble the inverter unit and the ignitor unit.
  • Do not turn on the HID bulb by using a power source other than the battery mounted on your vehicle.
  1. Make sure you have the anti-theft codes for the radio and the navigation system, then write down the XM radio channel preset. Make sure the ignition switch is OFF.
  2. Turn the combination light switch OFF.
  3. Disconnect the battery negative cable, then disconnect the positive cable.
  4. Remove the headlight assembly.
37a2a12.jpg
  1. Remove the Torx bolt using a Torx T20 bit.
  2. Turn the cover (A) 45 ° counterclockwise to remove it from the headlight assembly.
71b91a6.jpg
  1. Turn the socket (A) 45 ° counterclockwise to remove it from the bulb (B).
  2. Pull the retaining spring (C) away from the bulb then remove the bulb.
  3. Make sure the bulb harness (D) is routed correctly so it does not contact the reflector (E).
  4. Install the new bulb in the reverse order of removal. Make sure the notches in the bulb align with the tabs in the headlight.
  5. After reconnecting the battery, enter the anti-theft codes for the radio and the navigation system, then enter the customer's XM radio channel presets.

Posted on Feb 13, 2009

  • 1 Answer

SOURCE: need to replace low beam headlight on 2004 acura

replace head light right side 05 acura tl

Posted on Jan 03, 2010

  • 1 Answer

SOURCE: INVERTER REPLACE ON A 2003 TL ACURA

where can I purchase the inverter for a 2003 Acura 3.2 cl it is in the headlight

Posted on Feb 06, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 acura tsx headlight not working and need to put hi beam on


Fuse 28, a 10AMP fuse may be blown/bad. You may need a new one. Or your bulb may have burnt out. It's 12 years old. Any auto parts store guy could help you with it. (lower left side in this pic)
http://cimg0.ibsrv.net/cimg/www.acurazine.com/1024x768_85/240/fusediagram-164240.jpg

Video shows you how.
Blown Fuse Check 2004 2008 Acura TSX 2008 Acura TSX 2 4L 4 Cyl

Nov 16, 2016 | Acura Cars & Trucks

1 Answer

2004 acura tsx a/c blows warm drivers side only


Your system is either out of sync on the control, or the air temperature control blend door is not moving due a failure of the door or its actuator motor.

May 02, 2014 | 2004 Acura TSX

1 Answer

I have a 2004 Acura TSX that I just had maintenance work done on two weeks ago, and I was driving it yesterday and it made a irregular "clicking" noise, and then stopped after about 10 sec. and starte


only clickin i can think of that would make idling erratic is the timing has become out. and the pistons are hitting the valves. this would click or tap and eventually go bang. would not recommend reving or driving it till the timing has been checked.

Mar 04, 2018 | 2004 Acura TSX

1 Answer

Acura tsx drive side dome light only works if i turned on Manually it will not work at all when switch is in door mode, passenger side works normal


Sounds like an intermittent connection on the door switch.. Remove the switch, clean the contacts and recplace.

Aug 20, 2010 | 2004 Acura TSX

1 Answer

2004 Acura TSX Xenon light works intermitently


99% of the time the invertor is the problem with that condition

Apr 13, 2009 | 2004 Acura TSX

3 Answers

Maintenance required light wont reset on 2004 acura tsx M/T


be sure you are doing it in the right order push the trip/reset buttonturn the key "on"
Hold the button till the maint light goes out
turn the key off .
that will do it

Mar 25, 2009 | 2004 Acura TSX

2 Answers

Replacing HID headlight in 2004 Acura TL


HID Bulb Replacement

A transient high tension (25,000 V ) occurs at the bulb sockets of the high intensity discharge (HID) lamps when the combination light switch is turned ON, it may cause serious electrical shock or electrocution if you do not observe the cautions below.

CAUTION:
  • Never turn on the combination light switch before fitting the HID bulbs to their bulb sockets and completing the reassembly of the headlight assembly.
  • Do not service the headlights assembly in wet conditions, such as rain or snow, near a sprinkler system, or when your hands are wet to prevent electrocution.
  • Do not touch the surface of the HID bulbs with your bare hands and do not stain it with any oils and fats.
  • Do not disassemble the inverter unit and the ignitor unit.
  • Do not turn on the HID bulb by using a power source other than the battery mounted on your vehicle.
  1. Make sure you have the anti-theft codes for the radio and the navigation system, then write down the XM radio channel preset. Make sure the ignition switch is OFF.
  2. Turn the combination light switch OFF.
  3. Disconnect the battery negative cable, then disconnect the positive cable.
  4. Remove the headlight assembly.
37a2a12.jpg
  1. Remove the Torx bolt using a Torx T20 bit.
  2. Turn the cover (A) 45 ° counterclockwise to remove it from the headlight assembly.
71b91a6.jpg
  1. Turn the socket (A) 45 ° counterclockwise to remove it from the bulb (B).
  2. Pull the retaining spring (C) away from the bulb then remove the bulb.
  3. Make sure the bulb harness (D) is routed correctly so it does not contact the reflector (E).
  4. Install the new bulb in the reverse order of removal. Make sure the notches in the bulb align with the tabs in the headlight.
  5. After reconnecting the battery, enter the anti-theft codes for the radio and the navigation system, then enter the customer's XM radio channel presets.

Feb 13, 2009 | 2004 Acura TL

Not finding what you are looking for?
2004 Acura TSX Logo

Related Topics:

128 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

Marvin
Marvin

Level 3 Expert

81294 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...