Question about 2008 Chrysler Sebring

2 Answers

Reset oil change message.

How to reset the oil change message on an 08 chrysler sebring lx

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Chrysler Master
  • 412 Answers

YOU TURN IGNITION TO RUN POSITION..ENGINE OFF..PRESS ACCELERATOR 3 TIMES WITHIN 10-15 SECONDS..RELEASE AND TURN KEY OFF..THEN START VEHICLE,IT SHOULD BE RESET

Posted on Jul 14, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

It solved the problem for my 2007 Sebring. Put in "ON" position. You see the message flashing "Change Oil". Press accelerator right down to the floor 3 times right after the message starts to flash. Thank you rdebison.

Posted on Jul 15, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i reset my anti theft system on my 2004 sebring Lx


Try unconnect battery for 10 min and reconnect.
Try unlock door, lock door, unlock door, lock door, unlock door. Try starting car.

Jan 31, 2015 | Chrysler Sebring Cars & Trucks

1 Answer

I have a 2004 Chrysler Sebring Convertable 2.7 Liter. The oil light comes on even after ive just changed the oil. Is there a way to reset it?


Is your oil sending unit bad??? U can reset everything by unhooking the negative battery cable for a few minutes but i dont know if it will help your oil light..Check your connection at the oil sending unit and insure its got a good connection and check for shorts...

Nov 18, 2011 | 2004 Chrysler Sebring

2 Answers

After my recent Oil Change my Chrysler Seabring 2008 Seabring Convertible gives me a Change Oil Message each time I start the engine.


TRY RESETTING OIL CHANGELIGHT BY TURNING THE IGNITION SWITCH TO THE ON POSITION WITH ENGINE OFF.TURN IGNITION SWITCH ON 10 SECONDS PUMP ACCELRATOR SLOWLY 3 TIMES .UNTIL OIL CHANGE LIGHT FLASHES THEN IT HAS RESET.

Oct 18, 2010 | 2008 Chrysler Sebring

2 Answers

Tire specs for 2001 chrysler sebring


HI. Here is the complete line up of specs concerning your vehicles front and rear tires. You did not post the trim line of this car, so I posted all models and tire combination's specified by the manufacture.


2001 Chrysler Sebring Lim 2 Door Convertible Front and Rear Tires P205/60R16
2001 Chrysler Sebring LX 2 Door Convertible Front and Rear Tires P205/65R15
2001 Chrysler Sebring LX 2 Door Convertible Front and Rear Tires P205/60R16
2001 Chrysler Sebring LX 2 Door Coupe Front and Rear Tires P205/55R16
2001 Chrysler Sebring LX 4 Door Sedan Front and Rear Tires P205/65R15
2001 Chrysler Sebring LX 4 Door Sedan Front and Rear Tires P205/60R16
2001 Chrysler Sebring LXi 2 Door Convertible Front and Rear Tires P205/60R16
2001 Chrysler Sebring LXi 2 Door Coupe Front and Rear Tires P215/50R17
2001 Chrysler Sebring LXi 4 Door Sedan Front and Rear Tires P205/60R16

Jul 06, 2010 | 2001 Chrysler Sebring

2 Answers

Does anyone know where i can find an oil pan for a 2003 chrysler sebring lx, 2.4L DOHC 4 cylinder?


other than ebay, wreckers or a dealer, it may be cheaper to repair the one you have, sorry couldn't be more help, try craigslist as well. good luck

Jun 01, 2010 | 2003 Chrysler Sebring

4 Answers

I have a 2001 chrysler sebring lx wont turn over


Hope you got a good deal on that oil change. do you believe in coincidence. I can't imagine how an oil change could do anything to stop the engine from starting. So you have to rule out things like starter and fuel pump. to check the fuel pump go to a parts store and buy a can of starter fluid. Remove the top pf the air cleaner box. Have someone spray starter fluid into the opening going to the engine while you are trying to start the motor. If it fires up the pump is bad if not go on to the starter. For the starter locate the relay under the hood (in a fuse box) labeled for the starter. Remove it. Then run a wire from the positive terminal of the battery (careful not to ground to car) and touch where the relay plugged in. One of the points should kick the starter over. If none of them do i would suspect the starter. if all is ok the next possible suspect is the computer. You will need a dealer for this one but some computers have extended warranties because of problems so ask the dealer about it. I just had one replaced for a customer last summer on a 2001 Chrysler T&C and it was covered under warranty. Whole visit was around $200 If this helps please reply and good luck

Apr 27, 2010 | 2001 Chrysler Sebring

1 Answer

Changed oil and oil light still on


Try disconnecting neg battery cable for 10 minutes, then plug back in. It should reset the code. Otherwise use an obd2 scanner to reset it. If light is still on, the sensor may be bad. You can check with a voltmeter.

Oct 28, 2009 | 2004 Chrysler Sebring

1 Answer

Engine oil light still on in 08 mountianeer


Use Reset button on Right of Steering wheel: To reset CHANGE OIL SOON/OIL CHANGE REQUIRED message on the Message Center, press the SET UP control to access the System Check mode. Press and release the RESET button to display “OIL LIFE % HOLD RESET NEW” is displayed. Press and hold the RESET button for 2 seconds until “IF NEW OIL HOLD RESET” is displayed. Press and hold RESET button until “OIL LIFE SET TO 100%” is displayed.

Good luck and keep me posted and i'll try to explain again in a different way. Harder to tell then to show how to do it. 

Jul 22, 2009 | 2004 Mercury Mountaineer

2 Answers

To reset the change engine oil indicator


Owners manual should have the info you need to reset it

Dec 12, 2008 | 1999 Chrysler 300M

1 Answer

2004 sebring


If you are talking about the change oil message on your cluster. You need to press step until oil change mileage appears on screen and then just press reset.

If you are inquiring about the oil pressure swith on the engine there is no reset procedure. If you just replaced the oil pressure switch and still have no oil pressure, you are going to have to use a manual oil pressure gauge to make sure that you have engine oil pressure. If you have oil pressure with the manual guage there is a problem with the wiring or engine computer.

Jun 26, 2008 | 2004 Chrysler Sebring

Not finding what you are looking for?
2008 Chrysler Sebring Logo

1,175 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

Marvin
Marvin

Level 3 Expert

83850 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22413 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...