Question about Audi A6

1 Answer

1995 audi A6 ignition lock out (follow up) - A6 Audi Cars & Trucks

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Audi Master
  • 14,036 Answers

To get the ignition out you have to try toget the lock tight compound to break loose then support the steering column and drill out 2 shear bolts.using 1/8 drill bit.loosen the steering column boltsremove the left lower dash panel and left air deflector.slide steering column tube with the steering column downward and remove the steering lock from the steering column clamp.drill a hole in the center of the locking housing using a 1/8 drill drill bit.then push the retaining spring in with a punch and remove the lock cylinder. when you put it back it has to be lock tight. torque to 30 ft lbs.

Posted on Jul 11, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My audi a6 with automatic trany wont shift out of park and cant figure out why

dont pabnic it prob wont be transmission,, more likely a electric problem ,,, look at owners manual ,,, there is a lock solenoid to release park,,, there is a way to overridebit if solenoid breakes down,,,

Dec 01, 2013 | 1995 Audi A6

2 Answers

Timing belt 1995 Audi A6 Quattro Sedan (4A2) V6-2.8L (AAH)

Timing belt routing diagram for 1995 Audi A6 Quattro Sedan (4A2) V6-2.8L (AAH)

I can not insert the picture here because bad page. Send me your e-mail address, and I will send you back the picture.

Jun 16, 2012 | Cars & Trucks

1 Answer

1995 audi a6 won't start after replacing bad

1995? they did not have the immobilizer installed then, recheck your connections and does the starter turn over? look for open fuses also

May 08, 2011 | 1995 Audi A6

1 Answer

I1995 audi a6 quattro ignition switch does not return automatically to start position - i have to manually turn the key back 1/4 turn. can this be fixed, lubed or something?

Some can be repaired the first thing is to try a little wd40 in the key hole and work key in ignition, the spring back action is done by the switch not the ignition cylinder locjk, but if the lock binds up it will cause it not to return, so start with the lube, after a few days if it still doesnt return then remove covers and replace the switch on the back of key switch. hope this helps, most of the time the lube works.

Aug 30, 2010 | 1995 Audi A6

1 Answer

Surges of 3 to 26 and failures of idle speed

If the Battery is GOOD, the Alternator should produce a near constant of 13 to 13.4 volts at the Battery at all engine speeds. Your fluctuations recorded [if the multimeter is good] would indicate an uncontrolled open circuit from the Alternator, due to Regulator Failure, and a JUNK Alternator. Confirm by taking it to a reputable Accessory Store, where they will Bench Test it for FREE.
Regards, DT

Aug 28, 2009 | 1995 Audi A6

1 Answer

How to replace backup light switch Audi A6 Quattro 1995? How can I reach this switch?

This switch should be located on the side of the transmission and will have 2 wires coming out of it.

Aug 25, 2009 | 1995 Audi A6

3 Answers

Want to know where the ecu is in 1995 audi a6

no its under the passanger carpet under a plastic cover

Apr 22, 2009 | Audi A6 Cars & Trucks

2 Answers

My infrared remote does not work. I have an Audi A6 1995

Do you have memory seats as well? If so follow these steps I am going to refer to the keys as A and B as you have 2 of them
1) Unlock car with key A
2) Turn ignition into ON position with key A and roll down the window
3) Point Key B at IR Sensor and Click twice (perform both clicks under 5 seconds)
4) Turn off ignition and pull Key A out
5) Turn ignition into ON position with Key B
6) Point Key A at IR Sensor and Click once
7) Turn off ignition and Pull Key B out

Key A should be programmed as the Master Seat Program and Key B should be programmed for the Secondary seat program
So when you set your memory seats Key A is for Memory Position 1 and Key B is for memory position 2
if you don't have memory seats then you only have to point the receiver at the sensor and click once. That should just sync the IR Frequency and Codes

Feb 17, 2009 | 1995 Audi A6

1 Answer

Ignition barrel

I'm not positive which one it is but you can confirm this yourself online. Go to (VW Audi Group Catalog) and register for your particular car (it's free). The site gives you exploded diagrams for every system in the car, complete with OEM Audi part numbers. Get yours, then register for a similar year A4 as well, and see if its ignition switch carries the same part number. It's a great site for identifying parts and knowing what you're ordering when you go to the dealership.

Dec 16, 2008 | 1995 Audi A6

1 Answer

1995 audi a6

two bolts through middle(allen key)they are about halfway along you will see them if you look underneath near edges of number plate.....

Oct 26, 2008 | 2002 Audi A6

Not finding what you are looking for?

Open Questions:

0 Answers

2005 Audi Allroad A6 interior lights door locks windows not working. Fuse 14 is OK and already changed CCM. Hello, my 2005 Audi Allroad C5 platform had some water in the BACK of the car due to clogged sunroof drain. The car was parking upwards in a slope and the amp ceased to work correctly when I turned on and off the car, the speakers made a lound sound. I removed the water from the back of the car then parked it inside a roofed and level garage. Three days later the battery was dead so I replaced it and removed the amp on the back of the car. About two weeks later, the car alarm started behaving strangely it would not stop when I pressed the remote control key, and at times would not stop even while driving, and the power lock worked only some times. A few weeks later the power lock ceased to work altogether not working from the remote control key nor from the button on the door, the interior lights stopped working and the windows stopped working too. I checked the fuse #14 and it looks good, I even changed it with another fuse. There was some humidity under the carpet but not too much, and there was no sign of water inside the CCM box. The connectors of the CCM were also looking good. Anyhow, I bought another CCM with the exact same number but nothing changed. I don't know what to do now. One odd thing that may or may not be related: the internal motion sensor light on the driver's door pillar remains ON no matter if I push it. The internal motion sensor light will turn OFF without fuse #14, so while I look for a solution, I have been leaving fuse #14 disconnected for fear if having the battery drain again, but I'm wondering if this could have something to do with the door locks / windows / interior lights problem. Thank you for your help

Dec 18, 2018 | Audi Cars & Trucks

Cars & Trucks Logo

Related Topics:

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22413 Answers


Level 3 Expert

83850 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14571 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides