Question about Infiniti Q45

1 Answer

I have a 1991 infinty Q45 starts right up no error codes nothing on obd 1 computer, or dash readout runs good has 188801 on the odometer just so you know. When i acelerate it feels like a manaul transmision about to stall but not quite, that little shake they do up till 25 mph shifts smooth this is in drive but if i put it in 3 no overdrive i dont notice it, it accrelerates slow as well, hoping its not the tranny let me know thanks

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 331 Answers

Hi my name is Ray

No errors as of yet. normally is an indication of a fuel filter or fuel pump going out
the ECM does not monitor those 2 omnly that they are running rich or lean. At this point I would try changing the fuel filter first if it ends up being the pump you would have to normally change the fuel filter anyways. You may end up with a P0171 Fuel System Lean, Bank 1 you can see the codes here

http://www.6mt.net/forum/g35-sedan/5680-obdii-codes-how-clear.html

you may also try clening the air intake with carberator cleaner. this is where the TPS and anitknock snesor are located. sometimes dust gets on these sensors causing the sensor to misread. The misread is sent to the control module causing the car to run rough or even stall...

you can email me at techray1@live.com

please let me know

Posted on Jul 11, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of OBD port on a 1990 or 1991 Jaguar XJS with a V12 engine.


A good chance that your car does NOT have one. OBDll was not required by law until 1996.
Some manufacturers had there own systems before then.
I found the following web reference:

"Sorry fellas, the 1989 XJS has no onboard diagnostics at all. It only has a red feedback monitor hookup [with a blanking cap] back near the fueling ECU in the boot. It was used for mixture setup and that's pretty much it.
The trip computer fault code readout didn't arrive until 1992."
The trip commuter readout he refers was a way to get codes (after certain steps taken) to show up in the trip computer display.
For OBDll compliant cars .... the port has to be within 3 feet of the driver with full access .... usually under the dash
Helpful?

Jan 20, 2018 | Jaguar Cars & Trucks

1 Answer

Fuel economy readout quit working along with trip meter and odometer


Check fuses first if good remove battery cable on the positive side for a min or two, then check.
If still bad bring to dealer or shop to put it on the OBD scanner and check for codes.

Sep 11, 2015 | Cars & Trucks

2 Answers

Fuel/spark problelms with 1991 buick lesabre


Sounds like the timing is too low - if it is electronic timing id check the computer with a code scanner - something not quite right tho... but you dont want to spend good money after bad but.... that can be a bottomless pit!

May 06, 2017 | 1991 Buick LeSabre

1 Answer

Can I get the codes by using my on/off ignition switch or do I have to use a reader


To query and OBD-I-era computer for these codes, put the key in the ignition and turn the key to run (not start), then off, then run, then off, then run (that's 3 runs and 2 offs). Leave the key in the run position.

The check engine light will turn on for a few seconds, then turn off, then (sometimes after 20-30 seconds) start flashing. The flashes are counting out 2-digit trouble codes. Fast flashes count up each digit, with a longer pause between digits. On TJ's with a digital odometer, the code numbers are printed on the odometer in addition to flashing the check engine light. 55 indicates the end of all codes. Once you've got your code list, consult the table below to see what they mean.

OBD-II information is more complex, so the codes for 1998 and newer Jeeps can't be displayed by flashing the check engine light. However, those vehicles which have digital odometers will display the codes on the odometer. I've verified this personally on a 1999 WJ. For those vehicles without digital odometers, or for anybody who wants an English description rather than just a numeric code, an OBD-II code scanner ($100-300) can be plugged in under the dash. OBD-II codes can be looked up online here.


These codes were taken from the '95 XJ/YJ factory service manual.

I hope help you woth this. Good luck (rated this).

Oct 07, 2009 | 1998 Jeep Wrangler

2 Answers

I own a Q45 2005 Infiniti and the check engine recenty appeared. What is it?


You will need to take it to an Autozone, they run the scans for free and can tell you what is wrong. They can also sell you the part that is causing the code to pop up.

Sep 29, 2009 | 2005 Infiniti Q45

1 Answer

2002 S10 4 cyl 5 speed manual trans. Truck will not start, no power to starter, or starter relay, when turning key odometer readout goes blank in run position, and fuel gage appears to not power up aswell....


could be the security system. this same thing happened to my grandmothers s-10. she took it to dealer and sure enough thats where the problem lay. i would start there

Aug 01, 2009 | 2002 Chevrolet S-10

1 Answer

I put new brakes, front and rear on 1991 Infiniti Q45


go to a auto part like AUTOZONE they have the
code reader to erase the lite in dash it a free service

Apr 10, 2009 | 1997 Infiniti.5 Q45

2 Answers

Engine stalling


I assume the code (32) you mention is from a diagnostic readout tool.

If you do not have the original info that came with the readout, you may have to go to the tool manufacturer's website.

The entry P0032 on my Centech OBD II yields this:

"HO2S Heater Circuit High Voltage Bank 1 Sensor 1"

That doesn't make muchsense to me in view of your symptoms but maybe it will help.

Jul 05, 2008 | 1994 GMC Safari

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Infiniti Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14423 Answers

Are you an Infiniti Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...