Question about 1998 Ford Explorer

2 Answers

A/C ford explorer 1993

I have ford explorer 1993 i fix A/C check the leakage from pipe change the throttle by new one , change O-ring and vacume the system from air and charge it with 134a freon gas the A/C is working now but before 10 minutes i start the engine and run a/c i heard gas sound coming from set welf ( safety valve) & emmidatly i stoped a/c i don't know what is the reason please advice the weather here in iraq is very hot
is the reason is the hot of weather or still there is jam in the system but where ? if i replace the throttle
please advice me asap
regards

Posted by on

  • mases Jul 13, 2009

    thanks for advice but i don't replace a/c compressor with new one it's the original one i still use it , i will try to change the cylinder of filter i thinks it's old and need to replace with new one

  • mases Jul 15, 2009

    thanks for advice can i know what is the quantity of charge with Freon 134a cause i ready on compressor it's 1780 g of freon

    regards

    masis

×

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Ford Expert
  • 167 Answers

Posted on May 04, 2016

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 424 Answers

Whe you retrofitted the system to r134a ,did you subtract the amount from r12 to r134a. The system will hold less r134a than r12. It is roughly four oz less than r12.

Posted on Jul 13, 2009

  • Bill
    Bill Jul 15, 2009

    1993 came with r12 that is why I asked if you subtracted the difference.You have a fixed orifice tube in the system .

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

High idle o n a 1996 chrysler concorde. have change the tps and the idle air control valve. i think its a vacum line but i dont know which one. which one s effect the idle


High idle is usually caused by a vacume leak. First place to check is the cold air intake manifold. All hoses, throttle body, and sensors. Throttle Position(TPS), Mass Airflow(MAS), Idle Air Control Motor (valve) IAC. Controls Idle speed

A malfunctioning throttle system can cause both a high idle as well as an engine stall.

A dirty air intake or cracked air intake tube is often the culprit.

How to Fix an Engine High Idle in Under 15 Minutes

Oct 16, 2011 | 1996 Chrysler Concorde

1 Answer

I have changed IAC,EGR valve and pressure sensor, I have also cleaned out my throttle body and my 2002 explorer still stalls when I come to hard stops. Could this be a vacume line or an issue with my...


what is the idle speed like at rest,and with air cond on?when pumping the brake pedal at rest is there any change in idle speed and quality?
Have you had the system scanned for any fault codes or live data check?
How well was the throttle body cleaned,I have had a few that had to be cleaned a second time internally.
I hope this helps or get back with your findings.

Apr 03, 2011 | Ford Explorer Sport Cars & Trucks

2 Answers

I have a problem with my 1993 ford f250, there is hard shifting in the transmission, what could be the problem?


how long has it been since the fluid and filter been changed, also check to make sure that the transmission mount bolts are tight.

Feb 18, 2011 | 1993 Ford F250

1 Answer

1993 Explorer 4 wheel drive. it acts like it's not getting any gas. it wont idle and it dies every time i try to drive it. Black stuff was coming out the tail pipe and it runs better when you remove the...


It sounds to me like you have a big vacum leak in the intake or injection port. You can spray starting flud or carb cleaner around everything while its running when it speeds up you found the leak. You must be un pluging the map sensor vacum.

Jan 17, 2011 | Ford Explorer Cars & Trucks

1 Answer

I Had Ford explorer 2003 when i take stop engine shuts off any help?


I have seen many of these die out due to a broken or cracked vacum hose. Look under the hood and listen for a whistling or hi vacum noise. You can also take carb cleaner and spray around vacum hose and pcv valve and intake. If the motor revs up or stalls out when you do this then you definitl have a vacum leak. Find and replace.

If I am wrong about the vacum hose I woulds inspect idle air control motor, throttle position sensor, (both canbe cleaned as a temporary fix) or worst case may be a fuel pump.

Oct 22, 2010 | 2003 Ford Explorer

1 Answer

How do i chage the fuel injector for a geo metro 1997 LSI?


REMOVAL & INSTALLATION Fig. 1: Removing injectors from fuel rail 84245032.gif
Fig. 2: Make sure injectors rotate freely in cylinder head 84245033.gif
  1. Relieve fuel system pressure and disconnect the negative battery cable.
  2. Remove intake air hose between throttle body and intercooler.
  3. Remove accelerator cable.
  4. Unclamp PCV and fuel return hoses from deliver pipe.
  5. Unclamp injector wiring harness.
  6. Disconnect injector coupler.
  7. Remove cold start injector pipe from delivery pipe.
  8. Remove vacuum hose from pressure regulator.
  9. Remove fuel feed hose from delivery pipe.
  10. Remove pressure regulator from delivery pipe.
  11. Remove delivery pipe with injectors.
  12. Remove injectors from delivery pipe. To install:
  13. Replace injector O-rings and lubricate with fuel. NOTE: Make sure injectors rotate smoothly. If not, probable cause is incorrect installation of O-ring.
  14. Check if insulator is scored or damaged. If it is, replace with new one.
  15. Connect delivery pipe with injectors.
  16. Install pressure regulator to delivery pipe using a new O-ring.
  17. Install fuel feed hose to delivery pipe.
  18. Install vacuum and fuel return hoses to pressure regulator and clamp securely.
  19. Install cold start injector pipe to delivery pipe using new gaskets.
  20. Install injector coupler. Clamp injector wiring harness.
  21. Install PCV hose to cylinder head.
  22. Install throttle position sensor coupler.
  23. Install accelerator cable and adjust free-play.
  24. Install intake air hose to throttle body and intercooler.
  25. Connect the negative battery cable.
  26. Start engine and check for leaks.
prev.gif next.gif

Jul 03, 2010 | 1997 Geo Metro

1 Answer

1998 ford explorer with lack of power engine starts but rattles whole car at start and while driving down the road


I would check for vacume leaks in the engine area listen for air sucking like a vacume ...You can spray a small amount of throttle body cleaner on vac lines and the motor will rev up or bogg down that is a leak and need to fix all vac leaks ........If check engine light is on have your codes checked ....hope this helps

Nov 17, 2009 | 1998 Ford Explorer

2 Answers

On my 92 ford explorer my radiator petcock is leaking is there any quick fixes


If you can remove it, you can replace it either with the correct size NPT pipe plug or another petcock. I generally use a plug with teflon tape on the threads and drain by removing the lower hose...It's faster and easier than using the drain!

Nov 03, 2009 | 1992 Ford Explorer

Not finding what you are looking for?
1998 Ford Explorer Logo

914 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

gerry bissi

Level 3 Expert

4376 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...