Question about Cars & Trucks

1 Answer

Cause of very low headlights,when the bulb is new.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Cars & Trucks Master
  • 602 Answers

You have a bad ground on that side and it is feeding off the other side as in series cutting it's power in half.

Posted on May 02, 2015

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 118 Answers

SOURCE: 1986 300zx headlight problems

If I remember correctly nissan uses a L&R high and low beam fuses,might want to double check them,but if you need any diagrams just ask have a good day DB

Posted on Feb 17, 2009

greezy_je208
  • 237 Answers

SOURCE: Right low beam headlight out. Tried replacing

id be checking the fuses as they are run on seperate ones.

Posted on Dec 16, 2009

shastalaker7
  • 1515 Answers

SOURCE: Installed new low beam headlight and light will

Hi, if you have a meter to check the bulb, use it to check the wiring to the socket or wiring for power when light switch is turned on. You should have around 12 volts depending on year and type of truck or auto. If the old bulb was burned, you should have power there. When you turn on switch, the other side should work and you will know you have power and it may just be corroded. Check this and you should find the problem. Please keep me posted on this, I will be around to help you. Please rate me kindly if I have been of help to you.
Sincerely,
Shastalaker7

Posted on Jul 06, 2010

alicantecoli
  • 22114 Answers

SOURCE: The passenger side low beam headlight is not working, replaced with new light bulb but it still doesn't work

check the fuses as it has a fuse for each headlight if iam not mistaken

Posted on May 20, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What would cause the low beam headlight not to work when all other lights work?


If you have standard halogen bulbs:

  1. Burned out light bulb; or
  2. Fried wires between the dashboard wiring harness and the headlight bulb connectors; or
  3. Fried headlight bulb connectors.
If you have HEI emitters:
  • Failed ballast.

May 11, 2015 | 2002 Mercury Grand Marquis

1 Answer

How to change the bulb in 1999 RAV-4


Instructions
    • Open the RAV4's hood and locate the headlight bulbs plugging into the rear of the headlight assemblies. Each assembly has two bulbs, one outer and one inner. Unplug the wiring harness from the rear of the burnt-out headlight, by pressing the locking button and pulling down on the harness.
    • 2Grab the rear of the bulb and rotate the bulb about a quarter turn counterclockwise to unlock it. Pull the bulb from the headlight assembly.
      3
    • Grab a new 9005 (high beam) or 9006 (low beam) bulb by its plastic base. Insert the bulb in the rear of the headlight assembly, lining up the tabs on the bulb with the notches in the headlight assembly, and twist it clockwise to lock the bulb in place. Do not touch the glass part of the headlight bulb, as the oils from your hands can cause the bulb to fail prematurely.
    • 4Plug the wiring harness into the receptacle on the rear of the bulb

Jun 27, 2012 | 1999 Toyota RAV4

2 Answers

Can you give me the steps to change the headlight bulb


8ccc44f.jpg
You might have to jiggle the headlight while doing this, dust and rock particles get wedged in the tracks making it hard to slip out.

Oct 29, 2009 | 2005 Volkswagen New Beetle

1 Answer

How do you change the low beam headlight bulb?


You will have to remove the headlight assembly to whichever side is burneed out. It is a halogen bulb that gets replaced not the entire assembly. Careful not to touch the new bulb with your fingers as this will cause premature failure of the bulb.

Aug 15, 2009 | 2002 Buick LeSabre

1 Answer

Help changing the low beam, headlight


You'll need to pull up on the clips that hold the headlight in.. the clips are located on the back of the headlight and should be either white or black.. pull the clips straight up and you can then remove the headlight... remove the weather cover off the back of the headlight and pull the bulb out.. put the new bulb in but do not touch it... you should have an alcohol pad and clean the bulb with it before putting it in to make sure there's no residual oils left (oil will ruin the bulb and cause it to explode in the housing).. then pop the headlight in and put the weather cover on and slide the housing back in and clip it down...

Aug 10, 2009 | 2000 Oldsmobile Alero

1 Answer

How do you change the headlight bulb (low beam) on the passenger side of a 2000 toyota celica?


You should be able to access the buld holder from the rear of the headlight. It's a nylon bulb holder with a lock thing on it. You squeeze the lock part and turn it counterclock wise, and it should come out. Remove the old bulb and install the new one being careful not to touch the glass of the new bulb with bare fingers. The finger print you will leave can cause the bulb to prematurely die on you.

Jun 15, 2009 | 2000 Toyota Celica

2 Answers

One of my Headlight not working during low beam


Your low beam bulb filament is out -- replace the bulb.

May 29, 2009 | 2006 Dodge Caravan

1 Answer

Driver's side low-beam headlight out


Purchase the correct bulb, open your hood, unscrew the white retaining ring behind the non working lamp when loose turn black connection 1/4 turn counter clockwise till tabs line up pull straight back remove old bulb put on rubber gloves or BE CAUTIOUS NOT TO TOUCH NEW BULB GLASS WITH BARE FINGERS. Oils from your hands an cause bulb to heat unevenly and cause new bulb to explode in the headlight assembly
So with gloved hands open new bulb insert follow steps in reverse to reassemble. Happy Motoring

Feb 27, 2009 | 2008 Mercedes-Benz Mercedes Benz Clk Class

1 Answer

Burned out headlight/bulb bmw 1991 325i 2dr


It's a bulb replacement. If it's anything similar to my Audi, there is a cover on the back of the headlight housing that you pop off. Then you can reach in, pull the wire connector off the bulb, and unclip a metal retainer over the bulb, and pull the bulb out. Installation of the new one is the reverse. Just be SURE not to touch the glass part of the bulb. Skin oils can cause a halogen bulb to burn very hot and burn out very quickly. If you do touch the glass, wipe it gently but thoroughly on a cotton cloth to clean it off before you install it.

Oct 31, 2008 | 1991 BMW 3 Series

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...