Question about 2004 Citroen Berlingo 1.4

Open Question

How to remove and replace interior blower motor step by step instructions

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have to replace fan resister on my 2000 pontiac Montana do I to take out the blower motor to get at the resister


Step 1: Pry and remove the retaining pins (3) that secure the interior panel to the UNDERSIDE of the glove compartment area (near the PASSENGER'S feet).

Step 2: Disconnect the blower motor's wiring harness (1).

Step 3: Loosen and remove the 7/32 mounting bolts (3) that secure the blower motor to the vehicle. Pull the blower motor from the vehicle.

Step 4: Disconnect the wiring harness (1) mounted just to the LEFT of the resistor.

Step 5: Loosen and remove the 7/32 mounting bolts (3) that secure the resistor to the vehicle.


NOTE: You only need to LOOSEN the rear bolts, as the resistor will slide free without completely removing them!

Step 6: You can now slide and remove the resistor.

Step 7: Mount the new resistor by tightening the 7/32 mounting bolts (3). Connect the wiring harness (1).

Step 8: Reattach the blower motor by tightening the 7/32 mounting bolts (3).

Step 9: Connect the blower motor's wiring harness (1).

Step 10: Re-engage the retaining pins (3) to secure the interior panel to the UNDERSIDE of the glove compartment area.

Nov 12, 2016 | Pontiac Cars & Trucks

1 Answer

2000 Eldorado blower not working


INFORMATION
Subject:
Revised HVAC Blower Motor Installation Procedures

Models:
1994-1997 Cadillac Seville
1994-1999 Cadillac DeVille
1994-2002 Cadillac Eldorado

The intent of this bulletin is to provide technicians information regarding the proper installation of the Heating, Ventilation and Air Conditioning (HVAC) Module blower motor (with impeller) assembly.



The current available HVAC Module blower motor for the above listed vehicles can be identified by the three mounting holes (1). The original equipment blower motor had five mounting holes.

In order to avoid confusion and ensure a high level of customer satisfaction, when replacing an HVAC Module blower motor, refer to this bulletin for the appropriate procedure.

Eldorado/Seville-HVAC Blower Motor
Caution: Before servicing any electrical component, the ignition key must be in the OFF or LOCK position and all electrical loads must be OFF, unless instructed otherwise in these procedures. If a tool or equipment could easily come in contact with a live exposed electrical terminal, also disconnect the negative battery cable. Failure to follow these precautions may cause personal injury and/or damage to the vehicle or its components.

Removal Procedure
1. Disconnect the negative battery cable.

2. Remove the camshaft cover.

3. Remove the blower motor.

^ Disconnect connector from the blower motor.

^ Remove the blower motor screws (either 3 or 5 screws).

^ Remove the blower motor from the HVAC Module.

Installation Procedure
1. If present, remove the 2 ribs located on the barrier. Refer to Step 3 and the illustrations in the Instruction Sheet, P/N 52494110, found in the blower motor kit.

Important: Ensure the blower motor gasket makes a complete seal around the blower motor.

2. Install the new blower motor with heat shield. Refer to Steps 4 and 5 in the Instruction Sheet, P/N 52494110, found in the blower motor kit.

3. Install the blower motor retaining screws.

Tighten

Tighten the screws to 4 N.m (35 lb in).
4. Tighten the lower heat shield retaining screws to 4 N.m (35 lb in).

5. Connect the connector to the blower motor.

6. Install the camshaft cover.

7. Connect the negative battery cable.

Oct 09, 2012 | 2000 Cadillac Eldorado

1 Answer

Need step by step instructions on how to replace a resistor for blower motor on 2000 toyota camry


The blower motor resistor is under the dash on the passenger side of cabin to the left of the blower motor. Remove panels to access it. The resistor is the one with blue wires going to it on the left of picture below.
10_9_2012_10_43_43_pm.jpg

Oct 08, 2012 | Cars & Trucks

1 Answer

Heater has stopped working


(1) possible blown fuse.
Note that fuses blow for a reason - seek out the reason, or it will blow its new fuse too.

The main fuse block is located inside the left side of the engine compartment near the battery. There is also an interior fuse panel located just above the left side kick panel.

Interior Fuse Panel
The interior fuses simply unplug from the fuse panel. Use the fuse puller tool provided with your car to remove fuses from the panel. The tool is located on the back of the interior fuse panel cover.


(2) possible blower motor dead. See maintenance manual excerpt below.

(3) possible blower motor relay faulty. Location of Blower relay:
Under hood, drivers side, front engine area,rear of headlight housing; relay mounted on drivers side of radiator shroud.


1990-92 Mazda 626 and MX-6
See Figure below

archaeology_8.jpg
  1. Disconnect the negative battery cable.
  2. Remove the glove box and the underdash cover.
  3. Detach the electrical connectors from the blower unit.
  4. Remove the blower unit-to-fire wall attaching bolts and remove the blower unit assembly.
  5. Remove the blower motor fan-to-motor fastener.
  6. Remove the blower motor-to-unit attaching bolts, then remove the motor.
  7. Installation is the reverse of the removal procedure.

Feb 01, 2011 | 1991 Mazda 626

1 Answer

How do i replace the blower motor on a 94 chevy truck? step by step instructions would be helpful


go to the passenger side under the hood and the blower motor is face down on the top of the box. take out the screws and electrical plug and remove

Dec 16, 2010 | 1994 Chevrolet C1500

2 Answers

Chevy tahoe 1999 heater making noise when I put it on hi loud noise how do i fix it


Remove blower motor and inspect could have leaf's or something in it, also check blower motor shaft make sure blower shaft bearing are good.

Dec 09, 2009 | 1999 Chevrolet Tahoe

1 Answer

How do i get to my defroster on a 1997 jeep wrangler? it's quit working and i dont know what parts of the interior i need to remove to get to it.


its the blower motor in the dash. its on the passenger side. Go buy a chiltons or a haynes manual and it would walk you threw it. Good investment for the step by step instructions.

Nov 05, 2009 | 1997 Jeep Wrangler

1 Answer

97 4runner blower motor needs replaced. Do you


Hi. The removal is really easy; unplug the motor under the glovebox, and remove the 3 screws that holds the assembly in. You can have it out in 10 minutes.

Jul 09, 2009 | 1997 Toyota 4Runner

3 Answers

THE BLOWER MOTOR IS MAKING NOISES AND SMELLS


your bearing failed and is causeing friction replace motor

Jun 05, 2009 | 2001 Honda Accord

Not finding what you are looking for?
2004 Citroen Berlingo 1.4 Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Citroen Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14337 Answers

Are you a Citroen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...