Question about Acura Cars & Trucks

1 Answer

2000 acura integra gsr So I'm having a problem with my clutch, the clutch worked just fine until I took off the steel line from the slave cylinder I thought it was leaking metal on metal when pressed

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has achieved Level 3.

  • Master
  • 511 Answers

Hi Lance top up the resivour and open the Blead nipple at the slave cylinder. Let it flow unroll its clear of air. Keep the resivour topped up. When you think it's ok close nipple and continually pump clutch for about a minute if its still soft repeat the process. Good luck. Jim...

Posted on May 02, 2015


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a 2000 Honda Civic with B18B1 and GSR transmission. The engine and Tran are from an Acura Integra. I'm stuck in limp mode at 4000Rpm

check your fluid transmission or your clutch pack worn out and try to check your sensor connection

Jun 21, 2015 | Honda Cars & Trucks

1 Answer

How remove and replace clutch slave cylinder 1996 acura integra

10 mm line wrench and a 12 mm wrench or socket. Takes 2 people to bleed it. Look at your master cylinder inside the cabin, they leak too. Most people recommend replacing both at the same time. On a car this old, you might replace the rubber hydralic line too.

Jun 19, 2014 | 1996 Acura Integra GS-R

2 Answers

2000 hyundai elantra leaking clutch fluid, when low or empty lose clutch, then refill clutch works fine, leaking under car

The clutch hydraulic system is very simple, just 3 pieces. There is the clutch master cylinder with attached fluid reservoir-mounted on the firewall, there is a steel line from the master going down to the transaxle bell housing, and there is the clutch slave cylinder on the bell housing that the steel line connects to.
If yours is leaking under the car, it is probably the slave cylinder, either that or the steel line. Either one should be easy to replace.

Mar 17, 2014 | Hyundai Cars & Trucks

2 Answers

I have a 92 acura the pedal clutch sticks to floor and have no clutch

Clutch fluid...check the lines for leaks and what not. In my experience, the clutch is blow....prob need new pressure plate!

Sep 16, 2012 | 1992 Acura Integra Hatchback

1 Answer

What is the torque pattern for the head on a 96 acura integra gsr i already kno what ft. lbs they all are i just need to kno what pattern to torque them in

<P>all cylinder heads are the same start at the middle then work outwards like&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;</P><P>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;</P><P>start with 1/2 torque then 3/4 then full torque.then recheck ALL BOLTS after 250 miles.</P>

Aug 25, 2010 | 1996 Acura Integra GS-R

1 Answer

NEED a code for 1995 acura integra gsr? my radio stop working after i had my battery replace.

your radio may have had a security code activated,if so it will not work until it is re coded.....hope this helps.....cheers

Aug 09, 2010 | Acura Integra Cars & Trucks

1 Answer


Check the clutch hydraulics is properly bled of air,
Check clutch slave cylinder moves through its normal travel when clutch pedal de-pressed.

Sep 21, 2009 | 1992 Acura Integra Hatchback

2 Answers

1992 Honda Accord Master and slave cylinder replacement

You might still have air in the lines. When I changed the cylinders in my Honda it took a long time to get the lines to bleed out so the clutch would work properly.

Mar 16, 2009 | 1992 Honda Accord

1 Answer

New clutch installed on my 2005 Ford Focus 4 weeks ago. Today difficulty getting into 3rd gear then all the gears affected and eventually stuck in reverse gear only. Pick up truck took car back to the...

Sounds like air has gotten into the hydraulic clutch system, or it is low on fluid from a failed master or slave hydraulic clutch cylinder or connecting line between the master and slave cylinders.

Aug 27, 2008 | 2000 Ford Focus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts


Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides