Question about Cars & Trucks

1 Answer

Need to know what to torque head bolts too.and valve clearance on gehl 4835 skidsteer.deutz bf3m1011f motor

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 10,875 Answers

Need to know what motor??

Posted on May 02, 2015

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Torque setting for 1972 Cororna


My manual shows an 8RC for 70 and 71 and an 18RC for the 72-74

18RC valve clearance HOT IN .008 EX .014 cold spec. .007 .013
Cyl head 72-82 Ft Lbs
Rocker caps 12-17 ft lbs
cam bearing clearance .001-.002
cam endplay .0017-.0066
oil tube 11-16 Ft Lbs

Jun 15, 2013 | Cars & Trucks

1 Answer

Torque settingsfor head on lister petter mini6 engine


I have just rebuilt one for our Westerly 21. This is from my Petter 'A' range workshop manual:-
The water cooled engines (AC1W etc.) are:cylinder head nuts: 30NM (22 lbft) except 32.5NM (24 lbft) for the one that also holds the rocker.
Valve clearances are 0.1mm (0.004") COLDReset valve clearance after one hours running since torquing the head.
Retorque head and set valve clearance after initial 20 hours running
I believe Mini-6 refers to the water cooled engines but just in case, the air cooled engines are 27N (20 lbft)

Mar 27, 2012 | Cars & Trucks

1 Answer

Need torque spec's for 1999 Grand Am 2.4L motor valve pan gaskets bolts? thanks


I need know the torque head Pontiac Grand am se 1999. Machine 2.4

Mar 24, 2012 | 1999 Pontiac Grand Am GT

2 Answers

I need the torque for all the head bolts on my 1983 datsun 280zx


Check this information for 1983 Datsun 280ZX 2.8L (click over image for zoom)...

zjlimited_2038.jpg

Fig. 7: Cylinder head bolt removal sequence


zjlimited_2039.jpg

Fig. 13: Head bolt torquing sequence-1970-83 models

After repair job, temporarily install and tighten the two center (right and left) cylinder head bolts to 14 ft. lbs. (18 Nm).

Install the camshaft sprocket together with the timing chain onto the camshaft. Make sure that the marks made earlier, line up. If the chain will not stretch over the sprocket, the problem lies in the tensioner. Refer to the Timing Chain removal and installation procedure for the timing procedure, if necessary.

Install the cylinder head bolts. Note that two lengths are used. Tighten the bolts in sequence.
1970-71 models:
Tighten the bolts to 33 ft. lbs. (43 Nm)
Tighten the bolts to 47 ft. lbs. (61 Nm)

1972 models:
Tighten the bolts to 47 ft. lbs. (61 Nm)
Tighten the bolts to 55 ft. lbs. (71 Nm)

1973-83 models:
Tighten the bolts to 30 ft. lbs. (39 Nm)
Tighten the bolts to 44 ft. lbs. (57 Nm)
Tighten the bolts to 54-61 ft. lbs. (70-79 Nm)

To complete the installation, reverse the removal procedures. Adjust the valves to a preliminary COLD clearance of 0.2mm for the intake and 0.25mm for the exhaust. Operate the engine until it is at normal operating temperature, retighten the head bolts (loosen them slightly and retighten to the final torque figure) and adjust the valves to the HOT clearance specifications.

Hope this helps; remember to rating this answer and leave some testimonial comment about this.

Oct 13, 2011 | 1983 Nissan 280ZX

1 Answer

What is the valve clearance and head bolt torque on a nissan td27 engine 1996 model


valve clearance is .014 inch for intake and exhaust with engine warm.
head torque it 21 ftlbs, then 44 ftlbs, then loosen all, torque to 89 inchlbs, then to 21ftlbs, then mark and turn the bolts an additional 60 to 65 degrees.
cyl head sub bolts torque 80 to 100 inchlbs.
thanks.

Jan 13, 2011 | 1990 Nissan Hardbody King Cab

1 Answer

Settings and the valve clearances


Valve Setting is usually done only by authorised service center of Hundai, because if you do the setting wrongly it may hurt the car performance. Kindly go to the car service center or you can get the data only by visiting any Hundai service center directly.

May 08, 2010 | Hyundai Motor 1994 Elantra

1 Answer

Whats the valve clearance for toyota 4k engines and the torque for cylinder head bolts?


valve clearance is .20mm for the intake and .30mm for the exhaust. Will try to find cylinder head torque for you.

Jan 25, 2010 | 1983 Toyota Celica

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...