Question about Lincoln Town Car

1 Answer

How to change oil pump

How to rempve oil pump on the vehicle

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Lincoln Master
  • 3,218 Answers

The oil pump is located in the oil pan. You will have to remove the oil pan and then replace the oil pump. Not an easy task if you don't have experience

Posted on May 01, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to replace an oil pump on a 2005 Gmc Envoy XUV 4-wheel drive


Are you wanting to change the oil pump because the oil pressure flickers while idling after the engine has warmed up? If so change your oil pressure switch (located next to oil filter) first, to see if that fixes your problem. Sometimes dirty oil gets trapped in the switch and breaks down when the engine is warm. Replacing the oil pump is a major project requiring dropping the oil pan. Check U-Tube or a Haynes Repair Manual.

Sep 26, 2017 | GMC Cars & Trucks

2 Answers

Changed fuel pump oil pressure keeps going to 0 put in new oil sensor same oil pressure no problem before pump


Jeff, you or somebody else will have to hook up a external oil pressure Gage and verify oil pressure OK, before you have a catastrophic engine failure.

Feb 29, 2016 | Cars & Trucks

1 Answer

Oil pump replacement


Depends on what vehicle you have. Most pumps can be changed by dropping the oil pan. It may require raising the engine somewhat for the pan to clear the sump. Some vehicles have the oil pump run off the crankshaft on the side of the engine as well and are easier to access and change

Jan 06, 2016 | Cars & Trucks

1 Answer

Noise after oil pump changed jeep grand cherokee limited 1995


do not drive the vehicle check that the oil pump is working correctly
https://answers.yahoo.com/question/index?qid=20090117155735AA2VABY

Auto Repair Maintenance How to Check if an Oil Pump Is Bad

see links for assistance on how to check that oil pump is functionin correctly

Jul 06, 2015 | Jeep Cars & Trucks

1 Answer

How do I change a oil pump


  1. Drain the oil
  2. Remove the oil pan. You may have to lift or tilt the engine or remove frame members of the vehicle to do this, so it's probably the hardest part. Clean the gasket and seal surfaces on the engine block and crankshaft end bearings. Clean the oil pan. While you have the bottom of the engine open, inspect the cylinders for score marks and check for other anomalies such as sloppy piston bushings on the crank.
  3. Remove the oil inlet screen housing if it blocks access to the oil pump mounting bolts.
  4. Remove the oil pump. Clean the gasket/O-ring surface where it meets the engine block.
  5. Pour some clean oil into the outlet of the new oil pump (not so full you spill it when you install it). This will help it get oil into the engine more quickly on its first startup.
  6. Be sure you have the outlet gasket or O-ring in place!
  7. Install the new pump
  8. Clean or replace the filter screen assembly. Replace its O-ring and install on the oil pump.
  9. Reassemble the rest of the vehicle, using new gaskets and seals on the oil drain pan.
  10. Fill the new oil filter about 1/2 full of oil and install (always do this - it reduces the time the engine is turning dry after an oil change). This does not apply to vehicles that have open-face filters mounted in the bottom of the oil pan such as the 1980's Buick four-cylinder models.
  11. Add the rest of the oil in the usual manner.

Jun 06, 2011 | Honda CR-V Cars & Trucks

1 Answer

Oil light flashing on intermittently when at temperature and only at idle. Car 2008 Mitsubishi van Have had vehicle into Mitsubishi Agent and 2nd mechanic who all say vehicle in very good condition...


Well technically you should be using a 10W-30 with a vehicle like that unless it calls for a heavier grade. If the oil level is good (don't overfill it otherwise it can cause the light to go off) check the oil pressure switch and the oil sender unit. It is possible the oil pump is bad if it is fluctuating pressure or from running to heavy of a grade of oil you may have damaged the pump. The pump can test fine during diagnostics but usually wont fluctuate until under load.

Jan 30, 2011 | Mitsubishi Cargo Cars & Trucks

2 Answers

LOW OIL PRESSURE


to determine why your vehcle is showing low oil pressure,u need to first make sure oil filter is clean and not clogged
use correct viscocity oil
test oil pressure sending unit
test oil prssure gauge in dash
if all this checks out,then the oil pump needs replacing

Dec 16, 2010 | 2002 Ford Explorer

3 Answers

My 1981 Cadillac Deville 5.7L Diesel wont start. Ive checked all that I know including starter,battery,alternator,etc. Also, checked fuel pump, feul filter, fuel lines, injection pump. I topped off all of...


What does changing the oil,changing filters etc,have to do with the vehicle not starting?
What actual testing was done on --battery,alt,starter.fuel pump,etc.,how was this testing conducted and what were the results?
No fluids are consumed, in any motor vehicle,
If you have to top off,you have a leak,repair it!!

Sep 20, 2010 | Cadillac DeVille Cars & Trucks

2 Answers

1998 dodge caravan stalls with oil light on


I would stop driving it if I were you. Sounds to me like it might be the pump or a line that is clogged. New oil can break loose deposits in your motor and will end up in a oil pump pickup line, filter, or pump. And for your safety, here is a complete list of recalls on your vehicle. If your vehicle is affected by one or more of these recalls, then you may qualify for a free repair! http://www.internetautoguide.com/auto-recalls/09-int/1998/dodge/caravan/index.html
Have a nice day. And have someone check your van.

Jun 28, 2010 | 1998 Dodge Caravan

1 Answer

Changed oil pan gasket now i dont have much oil pressure


If oil pressure was fine before you changed the gasket, it's likely that some debris was loosened up (probably under the pan baffle) and got onto the oil pump pickup, restricting flow. The only other cause of low pressure would be worn engine bearings, which would not happen just by changing oil pan, unless you messed with either bearings or pump while pan was down. Remove the pan and carefully inspect the pump pickup for debris!!! DO NOT DRIVE VEHICLE 'TILL YOU HAVE CORRECTED THIS OR YOU WILL DAMAGE BEARINGS!!!

Feb 19, 2009 | 2000 Chevrolet Silverado 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

fordexpert

Level 3 Expert

5655 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...