Question about Pontiac 6000

1 Answer

Where is the ignition control module located on a Pontiac 6000 LE

Posted by on

  • paulmacintyre
    paulmacintyre May 01, 2015

    If a 6 cyl engine.. it is located under the ignition coil packs. You will have to unbolt the coils and remove the module assembly.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Pontiac Master
  • 21,873 Answers

On most models its the part the coils are connected to.

Posted on May 01, 2015

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 29 Answers

SOURCE: ignition problem

It should be underhood, driver side on upper firewall, it does not look like a typical ignition module, but I looked around and for your info, you can find a picture of it on autzone.com Hope this helps.

Posted on Sep 27, 2008

  • 22 Answers

SOURCE: ignition control module for 1995 Lincoln Continental

look on the dist. this is where the the wiring harness pluggs in

Posted on Nov 30, 2008

  • 1 Answer

SOURCE: ignition control module location for 1997 ford thunderbird?

1997 Ford Thunderbird Transmission problem
When driving normally transmission surges like it is not in gear. Had sensors replaced, nitural safety switch, and still acts up.

Posted on Dec 18, 2008

chuck943
  • 783 Answers

SOURCE: location of ignition control module

It does not have an ignition control module.
The electronic ignition (EI) for the 4.0L engine consists of the following components:
Crankshaft position sensor (CKP sensor) and 36 minus 1 tooth trigger wheel.
Ignition coil .
powertrain control module (PCM) .
Related wiring.
The PCM controls the firing of the coil based on the signal from the crankshaft position sensor.
The crankshaft position sensor (CKP sensor) is a variable reluctance-type sensor, triggered by a 36 minus 1 tooth trigger wheel configuration machined into the rear of the crankshaft vibration damper. The signal generated by this CKP sensor is called a CKP signal. The CKP signal provides the base timing and rpm information to the powertrain control module (PCM). Base timing is set at 10 degrees BTDC and is not adjustable.
If vehicle has no spark then turn key to on position,check engine light should come on.As you start cranking engine it should go out while cranking after about 10 secs. it should come back on(while cranking). If it come on then the PCM sees the signal,if it does not then PCM is not seeing it and this is your problem,either the CKP sensor or the wiring to it.

Posted on Mar 16, 2009

chuck943
  • 783 Answers

SOURCE: where is the ignition module control located on 1996 ranger 2.3 e

It does not have an ignition control module. The PCM (powertrain control module) fires the coil pack based on signal it recieves from the crankshaft position sensor and the camshaft position sensor.

Posted on Apr 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1989 pontiac 6000 le, car died while driving, had it towed , it started several times afterwards. Car was driven 1/2 mi and it died again, this time for good. Car will crank but will not start. Have...


check to see if the starter is ingaging or making a clicking sound when you have the hood up. If you do not hear the starter ingaging then its your starter but also you might have a ground issue too so use a multimeter if you know how and have one check things with this to see if there might be any short to the ground of car plus there might be bolts lose or missing as well you should check.

May 27, 2011 | 1989 Pontiac 6000

1 Answer

How to fix a coail pack on a 1987 Pontiac 6000?


Coil packs are replaced not repaired if found to be defective. ---prev.gif next.gif DISTRIBUTORLESS IGNITION SYSTEMS Starting in 1987, some models came with engines equipped with a Computer Controlled Coil Ignition (C3I) or Distributorless Ignition System (DIS). Fig. 1: Triggering system used on the C3I fast start system 86812034.gif
Fig. 2: Electrical schematic on C3I ignition system 86812031.gif Both DIS and C3I system consists of the coil pack, ignition module, crankshaft sensor, interrupter rings and ignition control module (ICM). All components are serviced as complete assemblies, although individual coils are available for Type 2 coil packs. Since the ICM controls the ignition timing, no timing adjustments are necessary or possible. Fig. 3: Wiring schematic used on the C3I ignition system 86812032.gif Fig. 4: Notch effect on the output signal used on the crankshaft sensor 86812033.gif
prev.gif next.gif

Oct 09, 2010 | 1987 Pontiac 6000

1 Answer

Cannot figure out how to test the crank shaft position sensor to see if it has caused recent ignition failure because the harness has three leads at the end that connects to the ignition modual and two...


If you unplug the crank sensor at the module and measure the resistance of the crank sensor. (the yellow wire and the black wire) The resistance of the crank sensor should be 900-1200 ohms.

May 17, 2010 | 1989 Pontiac 6000

1 Answer

Where is the starter on a 1988 Pontiac 6000 LE 4 cyl 2.5L ?


Should be between the engine and radiator underneath the car. You may be able to see it if you look down towards the oil pan, on the radiator side of the motor.

Mar 06, 2010 | 1984 Pontiac 6000 Le

1 Answer

1991 Pontiac 6000 LE ( Canadian ) Rear window de fogger not work


they have a relay also make sure conections are good on the window

Oct 23, 2009 | 1991 Pontiac 6000

1 Answer

Where do i locate the heater core in a 1991 pontiac 6000le


The heater core is inside the heater case. It is the same plastic case that houses the blower motor. Usually they are replaced under the hood near the firewall or under the dash. I would look at the free online repair manuals provided by parts stores such as autozone.com . They should have the info you need for your particular model.

Jun 03, 2009 | 1991 Pontiac 6000

1 Answer

No power


When you have no power, it is either the gas or the spark. Check fuel delivery systems to see if they are working. If it is spark, get a helper (in tennis shoes), and hold a plug wire to see if there is any spark when you crank the motor. If there is no spark, then look at your cap, rotor, and the black module under the cap. Over time, the module will quit working.
Most Sincerely, Kristopher Gerbracht

Feb 25, 2009 | 1985 Pontiac 6000

1 Answer

Where do i locate the heater core in a 1991 pontiac 6000le


the heater core is on the passenager side by the firewall but it has to be remove from the passenager under the glove box.

Feb 11, 2009 | 1991 Pontiac 6000

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...