Question about Ford Cars & Trucks

1 Answer

How to tune up a ford engine 2013model - Ford Cars & Trucks

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Ford Master
  • 948 Answers

There are some helpful videos on but I would have to know what kind of Ford 2013 you have. Try this one:

I hope this helps! :)

Posted on May 04, 2015


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Po 300 Po 316 Po420 Po430 2004 Ford Taurus. The car idle high or ruff when I start it in the morning but never shut off. After I got tune up it's worse it even shut off after running for a few mins

code p 0300 refers to random /multiple cylinder/s ---misfire detected ===causes spark plug/s---HT lead/s ---injector/s --ignition coil/s ---low compression---wiring
code p 0316 refers to misfire detected during start up--first 1000 revolutions ===causes --engine mechanical fault ---wiring---ignition system---fuel system--injector/s
code p 0420 refers to cat converter system, bank 1---efficiency below threshold === causes cat converter---HO2S 2
code p 430 refers to the same problem and causes as code p 0420
Here is a news flash .
engines under the control of an engine control module (ECM) do not need you to do a tune up as it tunes the engine 60 times a minute and reports to you by fault codes when it can no longer tune up the engine

Nov 04, 2015 | Ford Cars & Trucks

1 Answer

What parts do i need for a tune up

if it is an EFI engine then the parts that you will need for a tune up will be indicated in the fault codes
The ECM of the vehicle continually tunes the engine while running ( around 100 times a minute) and as long as all the sensors are within parameters ,the engine will remain in tune
any sensors that are failing will leave a fault code and just because the engine light is not on doesn't mean that there are no fault codes recorded
basically "good mechanics do not fix what isn't broken"

Aug 31, 2015 | 2000 Ford Excursion

1 Answer

1999 Ford Taurus won't stay started

when did tune up your engine? call ford auto parts department and ask them how many miles can you go between tune ups. spark plug wires, the coil and spark plugs wear out.

Dec 27, 2013 | 1999 Ford Taurus

1 Answer

Hey I got a 1996 ford explorer auto Running rich can I manual tune it

Rich running has nothing to do with a tune up unless the engine is misfiring, if it was misfiring you would have a blinking check engine light on while driving. Do an ODB2 fault code test, Autozone and Advance does this for free.

Feb 20, 2012 | 1996 Ford Explorer

1 Answer

Change major tune up parts ba gas milage ,will changing the fuel pump and changing out the gas tank help. 245,000

A Tune-up is a poorly used word

Spark Plugs are the only part that restores
your engine to where it was designed

ALL Tuning has been done by the On-Board-
Computer since 1981 on GM & 1983 for Ford & Chry
(OBD1) (OBD2 1996 thru 2011)

There is no major tune-up vs something else

You only replace a Fuel Pump when it fails

Apr 21, 2011 | 2002 Ford Escape

1 Answer

I have a 1998 Ford Explorer that just hit 190,000 miles yesterday and runs fantastic. Earlier this week, I had a tune up done. Today the check engine light began flashing, stays solid for a while, goes...

any time the check engine light is flashing it is the on-board computer telling you that the engine is misfiring, i think i would take it back to whom done the tune-up sounds like they may have cracked a spark plug or damaged a plug wire when they tuned it up.

Jan 29, 2011 | 1998 Ford Explorer

1 Answer

My wrench light is on after Ford flashed my computer (to help with the mileage) and messed up the tune for my CAI. I reloaded the tune to get rid of the engine light because the computer was throwing P001,...

Problem is ford can't back flash the computer as the car is new enough that your security system doesn't let you use a old computer from another cr and they have to flash the new one to make it work at all and only the updated flash is out now you may be backed into a corner. Run this story past your CAl tune spplier and they may be able to help ou they should have a tech lune or a founrm online and your not the only onedoing this so somebody knows what to do.

Sep 17, 2010 | 2006 Ford Mustang

1 Answer

Tune up directions


May 14, 2009 | 2001 Ford Expedition

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers


Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides