Question about Chrysler Cars & Trucks

Open Question

How do I change a fuel pressure regulator on a 2003 Chrysler Town and Country.

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

garyq1970
  • 73 Answers

SOURCE: changing fuel filter on 2004 chrysler town and country

  1. Remove or disconnect the following:
    • Negative battery cable
  2. Raise the vehicle and support the fuel tank with a transmission jack.
    • Fuel line from the front of the tank
    • Ground strap
    • Inboard side of the fuel tank straps and front T strap fastener and lower the tank about 6 inches
    • Fuel lines from the fuel pump module
    • Fuel filter
  3. Installation is the reverse of removal. Tighten the fuel filter bolts to 40 inch lbs. (4.5 Nm), the main tank straps to 40 ft. lbs. (54 Nm) and the T strap to 250 inch lbs. (28 Nm).
  4. Start the engine and check for leaks.

Posted on Aug 24, 2008

  • 2309 Answers

SOURCE: 2002 Chrysler Town & Country won't start

you got leaking injectors or seals, remove them and have them tested, most time all that is needed is new seals, and not expensive

Posted on Jun 29, 2010

  • 7353 Answers

SOURCE: 2000 Chrysler Town & Country smelling fuel

check the fuel filter connections first. If all ok, have a mechanic check it. If there is an evaporative leak, the check engine light should be on.

Posted on Jul 24, 2010

bonedivers
  • 1140 Answers

SOURCE: i just changed the fuel pump on my 2000 Chrysler

Remove gas cap and have someone turn on key, listen for pump to come on. If it does its only for about 5-10 secounds. If not look under hood for power distrubution panel (fuse and relay box) most of them will swap so remove fuel pump relay and swap with another one for testing. If it works then go buy relay.

Posted on Dec 15, 2010

racelinec189
  • 365 Answers

SOURCE: 99 Chrysler Town and Country idles high

Maybe a sticking choke or binding throttle linkage. Have you lifted the aircleaner cover and looked down carb opening? Choke stuck?
Could be a simple idle speed adjustment also. What rpm's do consider to be high. Maybe some carb cleaner down the barrels and throttle linkage could free it up. Again, it could be a simple idle adjustment depending on RPM's it's turning.

Posted on Apr 05, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the fuel pump regulator on a 2007 chrysler town & country 3.3 liter engine


Be sure to release the fuel pressure prior to removing the Pressure Regulator.
Fuel Pressure Regulator is under this clamp.
3c66e3a1-63b0-47c0-ba47-9e69a832f031.jpg

Sep 17, 2014 | Chrysler Town & Country Cars & Trucks

1 Answer

What keeps fuel pressure to injectors 2001 town country


The fuel filter has a regulator built into it. If you are losing fuel pressure after you turn off the key than this would be a good place to start.

Sep 14, 2014 | Chrysler Town & Country Cars & Trucks

1 Answer

How do i change a fuel pressure regulator on a 1996 town and country lxi van ?... while driving the van shuts off and all rpms go down and then comes back on .. Someone told me to replace the fuel filter ,...


The filter needs to be replaced first, if there is not enough volume or pressure reaching the fuel rails, the pressure regulator it's not going to work, nor can it be tested accurately. Filter cost less and and is fairly easy to replace. The filter is located above and on the inboard side of the fuel tank

Fuel pressure should be 38-45 psi . Check the pressure before and after you replace the filter.

The pressure regulator is mounted on the throttle body with (2) 10mm bolts. It has a vacuum line and fuel line attached. Remove the vacuum line, make sure the line has vacuum on it, not cracked or broken--- If the vacuum line has any gas in it, replace the regulator.

I hope this helps & good luck with your Chrysler.

Sep 01, 2011 | 1996 Chrysler Town & Country

1 Answer

03 Town and Country is shutting off while driving, but restarting almost immediately what are the most common reasons for this


Fuel: get your pressure checked at a shop, either the pump or regulator could be an issue

Spark: have a shop put a diagnostic unit on it and see if there is any history of spark failures. You will need a real diagnostic unit for this,not one of those 30 dollar analyzers from advance or autozone

Nov 01, 2010 | 2003 Chrysler Town & Country

1 Answer

2002 Chrysler Town & Country won't start


you got leaking injectors or seals, remove them and have them tested, most time all that is needed is new seals, and not expensive

Jun 29, 2010 | 2002 Chrysler Town & Country

1 Answer

2000 Chrysler T&C minivan: fuel delivery problems


The fuel pressure regulator is part of the fuel pump module Inside the Fuel Tank. Im Possitive of this, I Own a "Dodge Caravan" Witch is the SAME Vehicle, Just Name & SOME OPTIONS.

Oct 10, 2009 | 2000 Chrysler Town & Country

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...