Question about Lincoln Cars & Trucks

1 Answer

How do I change the cooling fan motor on my 99 Lincoln Continental

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Lincoln Master
  • 2,899 Answers

Radiator fan or heater fan.

If radiator fan:

Posted on May 01, 2015

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 94 Answers

SOURCE: Need to replace the left rad fan motor, any ideas on how to do it if i have the new part?

  1. Remove radiator from vehicle.
  2. Remove fan shroud retaining bolts, and cooling fan motor/blade/shroud assembly.
  3. Remove fan blade retaining clips and blades.
  4. Remove motor mounting screws and motors.
  5. If necessary, remove Constant Control Relay Module (CCRM).
  6. Reverse procedure to install. Torque CCRM screws to 40-56 in lb, and shroud retaining bolts to 24-48 ft lb.

Posted on May 27, 2009

  • 1 Answer

SOURCE: I have a 97 Lincoln Continental.

YOU NEED TO TAKE IT OUT FROM THE BOTTOM REMOVE PLASTIC SHROUD THEN DRIAN AND PULL LOWER RADIATOR HOSE FROM RADIATOR AND THE REST IS PRETTY SELF EXPLANATORY MAKE SURE YOU BUY THE CLIPS FOR THE WIRRING BEFORE YOU EVEN START

Posted on May 29, 2009

  • 691 Answers

SOURCE: The radiator cooling fan is not working. Upon

assuming fuse and relay are good..no fan should be running when the engine is cool/cold, the only time the fan should be running when it reach over operation temperature which then the fan kick on to bring the temperature back down to it operation temperature. both fan work in sync with one another, addition cooling is needed when the ac is running. when the last time have you replace thermostat and Thermos sensor/switch. I would replace both unit if you have not done so. The thermos/switch will turn the fan on when it reach certain temperature and cut off when it sense the temperature drop in the engine.

Posted on Aug 28, 2009

Testimonial: "Very good advice. I replaced the cooling fan myself and saved a lot of money. Everything is seems to be working. Thanks."

RJones1125
  • 373 Answers

SOURCE: 1997 lincoln Continental serpentine belt change

you need to find which pulley is the belt tensioner. use a socket and a breaker bar to lift the tensioner. once the belt loosen, slide the belt off one of the pulleys close to you. then slowly release the tensioner.

Posted on Oct 31, 2009

duane_wong
  • 6826 Answers

SOURCE: I need to remove the cooling fan shroud from my

Engine Fan REMOVAL & INSTALLATION 3.8L Engines

  1. Disconnect the negative battery cable.
  2. Remove the radiator upper sight shield.
  3. Disengage the electrical connector, then remove the integrated relay control/constant control relay module assembly located on the radiator support.
  4. Disconnect the fan electrical connector. Fig. 1: Disengage the fan electrical connector 86873115.jpg

  5. If necessary, remove the air bag crash sensor.
  6. Unbolt the fan/shroud assembly from the radiator and remove. Fig. 2: Unbolt the fan assembly from the radiator 86873116.jpg
    Fig. 3: Remove the fan from the engine 86873117.jpg
    Fig. 4: Slide the fan as an assembly up and away from the radiator. Be careful not to dislodge the mounting stud on the left side. 93143p56.jpg

  7. Remove the retainer and the fan from the motor shaft and unbolt the fan motor from the shroud.
  8. Installation is the reverse of the removal procedures. Tighten the fan shroud retaining bolt to 23–33 inch lbs. (2.6–3.7 Nm). Tighten the fan shroud retaining nut to 71–106 inch lbs. (8–12 Nm). Fig. 5: Constant control relay module location — 3.8L engines 86873118.gif
4.6L Engine
  1. Loosen the fan clutch-mounting shaft from the water pump hub.
  2. Loosen the fan shroud from its radiator mounting and remove the lower hose from the shroud.
  3. Lift the fan and clutch assembly and the fan shroud from the vehicle.
  4. If necessary, remove the fan-to-fan clutch retaining bolts and separate the fan from the fan clutch. CAUTION
    Closely examine the fan for cracks or separation, to avoid the possibility of personal injury or vehicle damage. To install:
  5. Assemble the fan and fan clutch. Tighten the retaining bolts to 15–20 ft. lbs. (20–27 Nm).
  6. Install the fan and clutch assembly and the fan shroud. Mount the fan clutch shaft to the water pump hub and tighten to 37–46 ft. lbs. (50–62 Nm).
  7. Slip the shroud into the lower mounting clips and install the shroud retaining screws. Fig. 6: Fan and fan clutch assembly — 4.6L engine 84173064.jpg
5.0L Engines
  1. Loosen the fan clutch-to-water pump hub retaining bolts.
  2. If necessary, remove the drive belt from the water pump pulley.
  3. Remove the fan shroud upper retaining screws. Lift the shroud to disengage it from the lower retaining clips.
  4. Remove the fan clutch-to-water pump hub bolts and remove the fan and clutch assembly and the fan shroud.
  5. If necessary, remove the fan-to-fan clutch retaining bolts and separate the fan from the fan clutch. CAUTION
    Closely examine the fan for cracks or separation, to avoid the possibility of personal injury or vehicle damage. To install:
  6. Assemble the fan and fan clutch. Tighten the retaining bolts evenly and alternately to 12–18 ft. lbs. (16–24 Nm).
  7. Install the fan and clutch assembly and the fan shroud.
  8. Install the fan clutch-to-water pump hub bolts.
  9. Slip the shroud into the lower mounting clips and install the shroud retaining screws.
  10. If removed, install the water pump drive pulley and adjust the belt tension; refer to Section 1.
  11. Tighten the fan clutch-to-water pump hub bolts evenly and alternately to 15–22 ft. lbs. (20–27 Nm). Recheck the belt tension.
prev.gif next.gif

Posted on Jul 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change the fan motor on my 99 Lincoln Continental?


Push up and turn the assembly the motor and squirrel cage will drop out

May 01, 2015 | 1999 Lincoln Continental

1 Answer

No fan control on ac and heat


check the fuse for the heater first then if that doesn't do it then you need to check the resistor unit..it is located near the fan and will have several wires on it...this part controls the different speeds for the fan and is after the fan due to the fact that it needs to be air cooled. these are not very expensive and are relatively easily changed...also, make sure the fan motor is good

Jan 10, 2011 | 1994 Lincoln Continental

1 Answer

Does both fans need to run on the lincoln continental


one fan is dedicated to the cooling and comes on when it needs to cool the coolant in the radiator, while the other fan is used when you run the air conditioner it helps cool the radiator when you add the workload of cooling the inside of the car. they work seperate from each other, while actually working together.

Jul 20, 2010 | 1998 Lincoln Continental

1 Answer

1999 continental


1998 to 2002......there are a few on ebay for $50.....and they are 8 pin connector types. Auto dim, compass, etc. Type in on the ebay motors page "Lincoln Continental Mirror" and you will find it.

Jul 13, 2009 | 1999 Lincoln Continental

1 Answer

Secondary fan ac motor doesn't work


That fan comes on with the a/c compressor to assist cooling while a/c is in use....diagnostics must be performed with a/c on for that fan to be energized...start at the relay in the underhood fuse/relay box and check for 12 volts to fan when a/c compressor clutch is energized

Jun 28, 2009 | 1997 Lincoln Continental

1 Answer

Need to replace the left rad fan motor, any ideas on how to do it if i have the new part?


  1. Remove radiator from vehicle.
  2. Remove fan shroud retaining bolts, and cooling fan motor/blade/shroud assembly.
  3. Remove fan blade retaining clips and blades.
  4. Remove motor mounting screws and motors.
  5. If necessary, remove Constant Control Relay Module (CCRM).
  6. Reverse procedure to install. Torque CCRM screws to 40-56 in lb, and shroud retaining bolts to 24-48 ft lb.

May 27, 2009 | 1996 Lincoln Continental

3 Answers

Diagram for 1998 lincoln continental


There should be a diagram of the route printed on the fan shroud or somewhere else under the hood of the vehicle.

Jul 09, 2008 | 1998 Lincoln Continental

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

fordexpert

Level 3 Expert

5470 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...