Question about Buick Riviera

Open Question

Wiring diagram for HEI distributor 307cid - Riviera Buick Cars & Trucks

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 169 Answers

SOURCE: need wireing diagram to change 72 nova over to hei distributor

Hey , just take the positive wire from the coil you are removing and feed it to the + terminal on the HEI dist. cap.the other terminal under there is for your tachometer. If you are mounting a master kill switch in the bumper for drag racing- attatch the kill wire to the tach terminal also.
Thats it you just plug the three wire pigtail from the dist. base(pickup) to the cap and you are off.
Remember firing order is 18436572 in a clockwise direction. to find #1 remove #1 plug and have someone"bump" the engine over while holding your finger over the hole-carefull. then line up the slotted mark on the crank pulley with the big notch on the timing indicator. Good luck

Posted on Aug 31, 2008

motor1258
  • 6674 Answers

SOURCE: HEI DISTRIBUTOR PROBLEMS

This should help, firing order is counterclockwise, 1,8,4,3,6,5,7,2.c9602d8.jpg

Posted on Aug 24, 2009

  • 582 Answers

SOURCE: HEI DISTRIBUTOR PROBLEMS

on the intake manifold you will see 8 numbers, this is your firing order
from the front of the car the left side numbers are 1,3,5,7 and the right side are 2,4,6,8. now ont the distributor cap there should be a number 1 at one of the plug towers. you start there with #1 plug wireand continue.
on a chevy the firing order is 18436572 and this is the order you put the wires on the cap. now the second problem i don't know right off hand which way the rotor turns on your engine. so remove the cap and crank the engine over and see which way the rotor turns, this is the order you put the wires back on the cap. hope this helps

Posted on Aug 24, 2009

  • 24 Answers

SOURCE: wiring an hei distributor

You shouldn't need a spark box because thee coil is located in the dist. cap. You need to run a 12v switched power source to the side of the dist. cap that is marked dist. if it isn't maked it is the term. that is on the front right of the conector pad. the one on the left is for hooking up a tach.

Posted on Oct 07, 2009

baugh55grfmj
  • 225 Answers

SOURCE: i need to see a diagram showing the cap on a hei

55a2f3f.jpg Here ya go.

Posted on Dec 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1973 chevy truck wiring diagram


The odometer uses the same cable the speedometer uses. It should be mechanical.
Now the HEI coil has two pinks and a brown. One pink goes to the pickup in the bottom of the distributor and the other pink goes to the key switch. The brown goes to the pickup or the ignition module in the distributor.

Jul 14, 2013 | Cars & Trucks

1 Answer

Wiring for a small block 350


need to know if its a HEI cap and rotor or not. HEI caps have the coil built into them , an all in one ignition as compared to a external cylindrical coil.
you need to know that. either the distributor cap is a huge hurken thing (HEI) or it has an external coil somewhere or the cap has a ninth distributor hole in the middle of the cap to put a coil. wire.
after you figure out which one it is then you have to either go to www.autozone.com and study chevy wiring or buy a haynes manual for the similar vintage engine. for the external coil I would try a chilton manual for a chev truck before 1972. for HEI anytime thereafter. I may be off by a few years on the age of the engine. but hopefully you got an idea of what to do, or just google chev engine wiring? and study away.
good luck

jm

Jul 27, 2010 | 1980 Chevrolet Corvette

1 Answer

Wire position for 75 Chevy 350 HEI on the


Order is 18436572. Put the timing mark on the crank at 0 and the rotor should be pointing either to the firewall or the front of the engine. If at the wall, turn the crank one more time and it is now pointing at the #1 wire position on the distributor.
left side cylinders are 1357 right, 2468 wire order is in the direction the rotor turns when cranking.

Apr 14, 2010 | Chevrolet Chevy Cars & Trucks

1 Answer

Where do i connect the green wire on atachometer on a HEI gmc ignition w/the coil seperate from the distributor?


GM HEI

Either go to the TAC terminal on the distributor or to the C- terminal/wire, which is typically a brown wire.

Oct 15, 2009 | 1987 Chevrolet Suburban

1 Answer

Hei distributor on old L6 engiune won't fire coil


'56 engine was likely a "blue flame" engine that had a points type ignition system. If someone installed a HEI setup in there, you need to know what year vehicle it came from. The old system used a hot wire from the ignition switch to the (+) side of an external coil...the (-) lead went to the points. The most common conversion uses the same (+) wire but it then connects to the "batt" terminal on the distributor cap.(coil is inside) There are no other wires involved except for the short harness that goes directly into the distributor that connects the coil, pickup coil and control module to each other..

Sep 18, 2009 | 1999 GMC Sierra 3500

1 Answer

HEI DISTRIBUTOR PROBLEMS


on the intake manifold you will see 8 numbers, this is your firing order
from the front of the car the left side numbers are 1,3,5,7 and the right side are 2,4,6,8. now ont the distributor cap there should be a number 1 at one of the plug towers. you start there with #1 plug wireand continue.
on a chevy the firing order is 18436572 and this is the order you put the wires on the cap. now the second problem i don't know right off hand which way the rotor turns on your engine. so remove the cap and crank the engine over and see which way the rotor turns, this is the order you put the wires back on the cap. hope this helps

Aug 24, 2009 | Cadillac DeVille Cars & Trucks

1 Answer

Need wireing diagram to change 72 nova over to hei distributor


Hey , just take the positive wire from the coil you are removing and feed it to the + terminal on the HEI dist. cap.the other terminal under there is for your tachometer. If you are mounting a master kill switch in the bumper for drag racing- attatch the kill wire to the tach terminal also.
Thats it you just plug the three wire pigtail from the dist. base(pickup) to the cap and you are off.
Remember firing order is 18436572 in a clockwise direction. to find #1 remove #1 plug and have someone"bump" the engine over while holding your finger over the hole-carefull. then line up the slotted mark on the crank pulley with the big notch on the timing indicator. Good luck

Aug 31, 2008 | Chevrolet Chevy Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...