Question about Honda Cars & Trucks
Posted by Anonymous on
Turn the fuel spigot on, change the fuel filter, and turn off the choke after it starts.
Posted on Apr 30, 2015
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: 2001 hyundai santa fe 6
OK. just follow the number on the ignition coils.
And the number on the cylinders are.
The FIREWALL side are 1,3,5, Starting from the belts location.
The RADIATOR side are 2,4,6, Starting from the belts location.
The coil with number 1 go to cylinder 1. as the same way the rest of the coils and cylinders.
OK... I hope this solve your question .
THank you for use fixya.
Posted on Jul 25, 2008
Check all of your grounds: There is one in front of the transmission leading from the negative wiring from your battery. Another goes from your battery wiring to the inside of your fender area. 10mm bolt. There is another on your driver's side motor mount to the valve cover. Check all relative fuses too.
Main Relay : Up above your gas pedal. Above your cruise control computer. It will be a gray box or a brown box about 3" square. TO DIAGNOSE: Try to tap it while you try to start it, you might need a helper. If this is it... Don't buy a new one, just pry the cover off of it and look close to find the broken solder connection. Heat the faulty pin until the solder puddles around it and your good to go. It's smaller than a human hair, look close and you'll see the loose connection.
Posted on Dec 29, 2009
Testimonial: "I'm going to check that first thing in the morning.I really do appreciate your help with this the holidays are over.Thank you very much"
SOURCE: my honda oddessey 1995, my
Hi, since you've replaced everything else, about the only thing left is the crankshaft position sensor. This is the sensor the computer uses to time the spark signals. Because this sensor is expensive, I recommend you test it first to verify it's bad before replacing. I have pasted test procedures below as well as replacement procedure in case it fails the tests. You will need an ohmmeter for the test. If you don't have an ohmmeter, you can buy one for as little as $10, or maybe you can borrow one. You will also need a timing light if you replace the sensor. Please let me know if you have questions, and thanks for using FixYa. Fig. Fig. 2: The Crankshaft Position (CKP) Sensor rotor looks like a small gear in the lower distributor housing- CRV and 1995 Odyssey models 7. Check and reset the ignition timing as outlined below. Fig. Fig. 1: The inductive lead of the timing light is placed around the No. 1 spark plug wire; and the light is aimed toward the marks on the crankshaft pulley. Fig. Fig. 2: The red ignition timing mark on the crankshaft pulley is lined up with the pointer. The two small notches on either side of the red colored notch represent the plus (+) or minus (-) 2° increments. The white notch to the far right is Top Dead Center (TDC)
TESTING CRV and 1995 Odyssey Models
CRV models: The blue and white wires. The resistance should be 300-700 ohms. 1995 Odyssey models: The blue/green and blue/yellow wires. The resistance should be 700-1,300 ohms.
REMOVAL & INSTALLATION CRV and 1995 Odyssey Models
ADJUSTMENT CRV and 4-Cylinder Odyssey Models
If equipped with an automatic transaxle, place the shifter in Park or Neutral. If equipped with a manual transaxle place the shifter in Neutral. Make sure to apply the parking brake and block the drive wheels.
Odyssey models with 4-cylinder engines: centrally located on the passenger side, under the dash. The connector has two wires; one is brown with a black tracer, and the other wire is red.
See Figures 1 and 2
2.2L/2.3L Odyssey 2.2L models: 13-17° at 650-750 rpm
Fig. Fig. 2: The Crankshaft Position (CKP) Sensor rotor looks like a small gear in the lower distributor housing- CRV and 1995 Odyssey models
7. Check and reset the ignition timing as outlined below.
Fig. Fig. 1: The inductive lead of the timing light is placed around the No. 1 spark plug wire; and the light is aimed toward the marks on the crankshaft pulley.
Fig. Fig. 2: The red ignition timing mark on the crankshaft pulley is lined up with the pointer. The two small notches on either side of the red colored notch represent the plus (+) or minus (-) 2° increments. The white notch to the far right is Top Dead Center (TDC)
Posted on Apr 03, 2011
Tips for a great answer:
Jan 27, 2016 | Cars & Trucks
Sep 06, 2012 | 1998 Toyota RAV4
Nov 29, 2011 | 1994 Honda Civic
If the engine has no spark, check for
voltage at the coil positive terminal when the ignition key is on. If NO
voltage, then problem is on the trigger side of the coil (pickup, crank sensor,
ignition module or primary wiring circuit).
But If there is NO voltage at the coil
itself, then in that case the problem is on the supply side (the ignition
switch or ignition wiring circuit).
But if the coil has voltage, then problem may be a bad high voltage output wire from the coil to spark plugs or hairline cracks in the coil output tower.------Getting this all possibilities checked will point towards the exact faulty part which is to be replaced.----------This should help.Thanks.Helpmech.
Dec 24, 2010 | Honda Accord Cars & Trucks
May 22, 2010 | 2000 Dodge Caravan
Nov 01, 2009 | 1993 Ford F150 SuperCab
Jul 17, 2009 | 2002 Kia Rio
Dec 02, 2008 | 1997 Chevrolet Cavalier
Dec 01, 2008 | 1989 Ford F 350
Nov 23, 2008 | 1994 Ford Aerostar Extended
Sep 19, 2017 | Honda Cars & Trucks
Sep 18, 2017 | Honda Cars & Trucks
13 people viewed this question
Usually answered in minutes!