Question about 1986 Pontiac Firebird

Open Question

How do I replace the shifter interlock cable?

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Transmission won't shift into gear only park works no prior problems just all of a sudden stop Lincoln Continental 2001


I would say it has something to do with this !
Shift Interlock System An ignition/shifter interlock mechanism is installed to prevent shifting the transaxle out of the PARK position unless the ignition switch is rotated to RUN and the brake pedal is applied. The floor shift interlock system consists of:
  • an actuator assembly integral to the ignition/shifter interlock cable assembly.
  • a bracket retaining the actuator.
  • the necessary wiring.
The solenoid is energized when the ignition switch is turned to the RUN position, locking the transaxle range selector lever in the PARK position. When the brake pedal is applied and the stoplight switch (13480) is activated, the ignition/shifter interlock actuator is deactivated and the transaxle range selector lever can be moved out of the PARK position.

Dec 17, 2016 | 2001 Lincoln Continental

1 Answer

The linkage are hooked up but the car still want go into park,a 2000 Taurus


Do you have floor console shifter ?
Shift Interlock System A brake/shifter interlock system consists of the following:
  • ignition switch (11572)
  • brake pedal stoplight switch (13480)
  • brake shift interlock module
  • brake shift interlock solenoid assembly (attached to key interlock assembly)
  • necessary wiring
On floor-shift vehicles, the ignition/shifter interlock cable (3F719):
  • locks the floor shift transaxle range selector lever in the PARK position when the ignition switch is in the LOCK position.
  • requires the floor shift transaxle range selector lever to be in the PARK position to turn the ignition switch to the LOCK position.

May 04, 2015 | 2000 Ford Taurus

1 Answer

How to replace shifter and shifter interlock cable on a 2006 jeep liberty


pop up the console screws in side of it and pop out around shifter basel 4 bolts hold shiter

Sep 24, 2013 | 2006 Jeep Liberty

1 Answer

Brake lockout cable connected to the shift interlock latch


Need more details.
Dodge Charger RT & SRT have weak plastic shifter assemblies. The brake interlock works first to let you move the shifter to the right. Then the shift interlock needs to release to let you shift down the gate. I can tell you how to get by until you can replace the assembly if you give more information than just a title.

Aug 22, 2012 | 2006 Dodge Charger

2 Answers

My shifter wont shift from park to drive brake lights work 94 civic


You may have a bad switch (Ford calls it a brake shift interlock not sure the exact term Honda uses) but check all your fuses. Below I gave you a picture and instructions on how to bypass the interlock switch until you can get the repair done or replace the bad fuse. I hope this helps and good luck.


clifford224_905.gif

clifford224_906.gif
clifford224_907.gif

Jun 26, 2011 | Honda Civic Cars & Trucks

3 Answers

What is shift lock release, and how do I use this option???


shift lock located on your shifter by sticking a key or an small object into the hole to release the lock; Only used when need to shift out of gear if the battery is dead OR the brake sereniod switch goes bad and wont release the lock to the shifter when applying pressure to brake peddle to allow you to move shifter into gear. also state in owners manuel.

Aug 28, 2009 | 2004 Hyundai Elantra

2 Answers

Gear shifter does NOT shwitch from park and break


SHIFTER LOCKED IN PLACE

  1. Remove the instrument panel cover below the steering column, then remove the steering column shrouds to gain access to the brake transmission shift interlock (BTSI) solenoid. The solenoid is part of the interlock cable assembly.
  2. Disconnect the wire connector from the rear of the BTSI solenoid.
  3. Insert the ignition key and turn it to the ON position.
  4. With the brakes applied, try moving the shifter out of the PARK position.
    • If the lever now moves freely in and out of PARK, perform the Circuit Test below.
    • If the shift lever still does not move from the PARK position, remove the BTSI solenoid from the shift lever assembly. If the shift lever now moves freely in and out of the park position, the BTSI solenoid is faulty and the interlock cable must be replaced. If the shift lever still does not move from the park position, the problem is in the shift lever assembly or the ignition interlock cassette

May 09, 2009 | 1998 Honda Accord

1 Answer

Remove ignition tumbler


lock cylinder removal

Section 11-04: Steering Column 1996 Escort, Tracer Workshop Manual
REMOVAL AND INSTALLATION Ignition Switch Lock Cylinder Removal
  1. stf~us~en~file=ani_caut.gif~gen~ref.gif WARNING: THE ELECTRICAL CIRCUIT NECESSARY FOR DRIVER SIDE AIR BAG MODULE DEPLOYMENT IS POWERED DIRECTLY FROM THE BATTERY. TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE PERSONAL INJURY, THE BATTERY GROUND CABLE MUST BE DISCONNECTED PRIOR TO SERVICING OR REPLACING ANY DRIVER SIDE AIR BAG MODULE SYSTEM COMPONENTS.
    Remove the steering wheel (3600). Refer to the procedure in this section.
  1. Remove the multi-function switch (13K359). Refer to Section 11-05 for the removal procedure.
  1. Disconnect the ignition switch electrical connector.
  1. Remove the ignition/shifter interlock cable mounting bracket bolt and position the ignition/shifter interlock cable mounting bracket and the ignition/shifter interlock cable (3F719) aside.




  1. Remove the four steering column upper mounting bracket bolts and lower the steering column (3C529).
  1. Use a hammer and chisel to make a groove in the head of each of the two ignition switch lock cylinder bracket bolts.


    0764353.gif

  1. Remove the two ignition switch lock cylinder bracket bolts with a screwdriver and discard the bolts.




  1. Remove the ignition switch lock cylinder and the ignition switch lock cylinder bracket.
Installation
  1. Position the ignition switch lock cylinder and bracket and install two new bolts, tightening them only enough to hold the ignition switch lock cylinder in position.
  1. With the key in the ignition, verify the operation of the ignition switch lock cylinder. If necessary, reposition the ignition switch lock cylinder until it operates properly.
  1. Tighten the ignition switch lock cylinder bracket bolts until the bolt heads break off.
  1. Position the steering column and install the four steering column upper mounting bracket bolts. Tighten the steering column upper mounting bracket bolts to 9-14 Nm (80-124 lb-in).
  1. On vehicles equipped with tilt column, remove the upper mounting bracket retaining pin.
  1. Position the ignition/shifter interlock cable mounting bracket and install the bolt. Tighten the ignition/shifter interlock cable mounting bracket bolt to 4-6 Nm (35-53 lb-in).
  1. Connect the ignition switch electrical connector.
  1. Install the multi-function switch. Refer to Section 11-05 for the installation procedure.
  1. Install the steering wheel. Refer to the procedure in this section.
  1. Inspect the shift interlock system. Refer to Section 07-05 for the procedure.

Apr 07, 2009 | 1995 Mercury Tracer

2 Answers

Gear shifter is not moving when u press on break


center console shifter? if so, likely could be a misadj shift cable, you can pull loose top cover per instruction maneul tells you how to get out of park till you can get it adj, or repaired

Apr 01, 2009 | 2004 Ford F150

4 Answers

Need to replace the shifter cable on a 2003 PT Cruiser


Have the EXACT same problem. 2005 Pt Cruiser w about 88,000 miles. Became hard to shift when cold and then bam ....something broke. Moves freely. I know I'm going to get screwed on this... what should it cost to have it fixed. The guy at a shop close by (figured close to make towing easier) started into this 'its a dealer only part and blah blah...at least an hour .... " He's going to send an estimate tomorrow. I'm in E. metro Atlanta

Feb 05, 2009 | 2003 Chrysler PT Cruiser

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...