Question about Ford Mustang

Open Question

Would a F8SB-15607-AC transciever work in a 1997 ford mustang 3.8 litter.

Posted by on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 99 Answers

SOURCE: 1997 Ford Mustang won't go out of PARK!! HELP!!

The brake light switch at your pedal is defective, or more likely, the wire at the connector broke or came loose. If you need to move it in an emergency, turn off the car, place it in neutral, and start it. Mind you that you still will not have brake lights. The switch is an easy fix.

Posted on Aug 11, 2008

oldfishead
  • 155 Answers

SOURCE: 1997 mustang rear running lights dont work front

assuming you have brake lights and marker light, I would check the socket for voltage, both the contacts and probe the wire (Brown) for voltage...it could be a bad socket.... if no voltage, trace the "Bwn" wire back and keep probing til you find voltage, check the connector in the trunk on the LT/RT side also...hope this helps you...GL

Posted on Jul 08, 2009

grouchyroan
  • 2 Answers

SOURCE: AC don't work in 1998 ford mustang, does the CCRM need replaced?

just finished repairing this problem on 98 mustang, the fan didn't operate at full speed and a/c compressor had no signal, it was the ccrm, or air cond control module located on passenger side behind plastic inner fender, also accessible under hood if you remove air filter box and reach through hole, the replacement has to have the same large letter on top of module, example, mine had a large S, i think this corresponds to a letterin vin but not sure, but it does have to be the same. controls fan and speed of fan, fuel pump and a/c compressor

Posted on Aug 07, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to locate the fuse for ac blower on a 1997 ford gt mustang


Under the hood you'll find a relay center. In that box, you'll find the A/C relay. If you're A/C isn't coming on, this could be the problem. To test it, swap it out with a relay next to it and see if it comes on. If it does, replace the relay. If it doesn't still, look in the fuse box to see if you in fact have a blown A/C fuse. The fuse box itself is located under the dash.

Jul 03, 2014 | 1997 Ford Mustang Cobra

1 Answer

Wire in a Ford PATS Transceiver F8SB-15607-AC Ignition Lock Cylinder and Key FOB Explorer


i've found a few references on how to by pass this but if you follow this link to the ford explorer forum you will get better info and advice from fellow explorer owners/mechanics who know the vehicle from top to bottom
2002 ford PATS transceiver XLT won start

May 21, 2014 | 1999 Ford Explorer

1 Answer

Ac not working


lots of possibilitys, 1. blown fuse
2. low on refrigerant, will not let the pully to engage
3 nothing bad about fords, but they use plastic for air dams, inside of the hot and cold deck
4. try to change from cold to hot if it does not change refer to 3.
hope this helps

Aug 13, 2013 | 2000 Ford Mustang

1 Answer

Compressor make noise


check AC compressor belt could be slipping.

Jul 09, 2013 | Ford Mustang Cars & Trucks

1 Answer

How can i replace the ignition actuator in a 1995 mustang?


By litterally dismantling the column completely. It may look simple enough in a book, but it takes a lot more time than putting in junkyard unit.

Dec 11, 2011 | 1995 Ford Mustang

1 Answer

What is the firing order in a 1997 Ford Mustang 3.8 V6


1997 Ford Mustang 3.8 liter V-6 VIN "4"

Cylinder # passenger side radiator to firewall, 1-2-3
Cylinder # passenger side radiator to firewall, 4-5-6

Coil numbering
Radiator side, passenger to driver side 5-6-4
Fire wall side, passenger to driver side 1-2-3

Thank you for using fixya and good luck

Apr 11, 2010 | 1997 Ford Mustang Cobra

1 Answer

I need the routing diagram for the serpentine belt on a 1997 Mustang 4.6 liter.


1997 FORD MUSTANG - V8 4.6L 281ci GAS FI N V
Belt Routing Diagram Multiple Accessory

4a2f6ad.jpg



1997 FORD MUSTANG - V8 4.6L 281ci GAS FI N X
Belt Routing Diagram Multiple Accessory
bd5c8ac.jpg


Hope this help (remember rated and comment this).

Mar 29, 2010 | 1997 Ford Mustang Cobra

1 Answer

How to take the exhaust manifolds off so i can remove the heads on a 4.6 v8 in a 97 mustang gt


DO YOU HAVE 4.6L SOHC ENGINE.YOU ARE GOING TO HAVE TO TAKE OUT ALOT MORE STUFF.AND YOUR AC SYSTEM HAS TO BE DISCHARGED THE AC COMPRESSOR HAS TO BE REMOVED. NOW IF YOU HAVE 4.6L DOHC YOU DONT HAVE TO REMOVE ALOT OF PARTS TO GET EXHAUST MANIFOLD OFF. WHICH ENGINE DO YOU HAVE.

Sep 21, 2009 | 1997 Ford Mustang Cobra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...